// SPDX-License-Identifier: GPL-2.0+
//
// Copyright (c) 2004-2006 Simtec Electronics
// Ben Dooks <ben@simtec.co.uk>
//
// S3C24XX Power Manager (Suspend-To-RAM) support
//
// See Documentation/arm/samsung-s3c24xx/suspend.rst for more information
//
// Parts based on arch/arm/mach-pxa/pm.c
//
// Thanks to Dimitry Andric for debugging
#include <linux/init.h>
#include <linux/suspend.h>
#include <linux/errno.h>
#include <linux/time.h>
#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/serial_core.h>
#include <linux/serial_s3c.h>
#include <linux/io.h>
#include <mach/regs-clock.h>
#include <mach/regs-gpio.h>
#include <mach/regs-irq.h>
#include <mach/gpio-samsung.h>
#include <asm/mach/time.h>
#include <plat/gpio-cfg.h>
#include <plat/pm.h>
#include "regs-mem.h"
#define PFX "s3c24xx-pm: "
#ifdef CONFIG_PM_SLEEP
static struct sleep_save core_save[] = {
/* we restore the timings here, with the proviso that the board
* brings the system up in an slower, or equal frequency setting
* to the original system.
*
* if we cannot guarantee this, then things are going to go very
* wrong here, as we modify the refresh and both pll settings.
*/
SAVE_ITEM(S3C2410_BWSCON),
SAVE_ITEM(S3C2410_BANKCON0),
SAVE_ITEM(S3C2410_BANKCON1),
SAVE_ITEM(S3C2410_BANKCON2),
SAVE_ITEM(S3C2410_BANKCON3),
SAVE_ITEM(S3C2410_BANKCON4),
SAVE_ITEM(S3C2410_BANKCON5),
};
#endif
/* s3c_pm_check_resume_pin
*
* check to see if the pin is configured correctly for sleep mode, and
* make any necessary adjustments if it is not
*/
static void s3c_pm_check_resume_pin(unsigned int pin, unsigned int irqoffs)
{
unsigned long irqstate;
unsigned long pinstate;
int irq = gpio_to_irq(pin);
if (irqoffs < 4)
irqstate = s3c_irqwake_intmask & (1L<<irqoffs);
else
irqstate = s3c_irqwake_eintmask & (1L<<irqoffs);
pinstate = s3c_gpio_getcfg(pin);
if (!irqstate) {
if (pinstate == S3C2410_GPIO_IRQ)
S3C_PMDBG("Leaving IRQ %d (pin %d) as is\n", irq, pin);
} else {
if (pinstate == S3C2410_GPIO_IRQ) {
S3C_PMDBG("Disabling IRQ %d (pin %d)\n", irq, pin);
s3c_gpio_cfgpin(pin, S3C2410_GPIO_INPUT);
}
}
}
/* s3c_pm_configure_extint
*
* configure all external interrupt pins
*/
void s3c_pm_configure_extint(void)
{
int pin;
/* for each of the external interrupts (EINT0..EINT15) we
* need to check whether it is an external interrupt source,
* and then configure it as an input if it is not
*/
for (pin = S3C2410_GPF(0); pin <= S3C2410_GPF(7); pin++) {
s3c_pm_check_resume_pin(pin, pin - S3C2410_GPF(0));
}
for (pin = S3C2410_GPG(0); pin <= S3C2410_GPG(7); pin++) {
s3c_pm_check_resume_pin(pin, (pin - S3C2410_GPG(0))+8);
}
}
#ifdef CONFIG_PM_SLEEP
void s3c_pm_restore_core(void)
{
s3c_pm_do_restore_core(core_save, ARRAY_SIZE(core_save));
}
void s3c_pm_save_core(void)
{
s3c_pm_do_save(core_save, ARRAY_SIZE(core_save));
}
#endif
