// SPDX-License-Identifier: GPL-2.0-only
/*
*
* arch/arm/mach-u300/core.c
*
* Copyright (C) 2007-2012 ST-Ericsson SA
* Core platform support, IRQ handling and device definitions.
* Author: Linus Walleij <linus.walleij@stericsson.com>
*/
#include <linux/kernel.h>
#include <linux/pinctrl/machine.h>
#include <linux/pinctrl/pinconf-generic.h>
#include <linux/platform_data/clk-u300.h>
#include <linux/irqchip.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>
#include <linux/clocksource.h>
#include <linux/clk.h>
#include <asm/mach/map.h>
#include <asm/mach/arch.h>
/*
* These are the large blocks of memory allocated for I/O.
* the defines are used for setting up the I/O memory mapping.
*/
/* NAND Flash CS0 */
#define U300_NAND_CS0_PHYS_BASE 0x80000000
/* NFIF */
#define U300_NAND_IF_PHYS_BASE 0x9f800000
/* ALE, CLE offset for FSMC NAND */
#define PLAT_NAND_CLE (1 << 16)
#define PLAT_NAND_ALE (1 << 17)
/* AHB Peripherals */
#define U300_AHB_PER_PHYS_BASE 0xa0000000
#define U300_AHB_PER_VIRT_BASE 0xff010000
/* FAST Peripherals */
#define U300_FAST_PER_PHYS_BASE 0xc0000000
#define U300_FAST_PER_VIRT_BASE 0xff020000
/* SLOW Peripherals */
#define U300_SLOW_PER_PHYS_BASE 0xc0010000
#define U300_SLOW_PER_VIRT_BASE 0xff000000
/* Boot ROM */
#define U300_BOOTROM_PHYS_BASE 0xffff0000
#define U300_BOOTROM_VIRT_BASE 0xffff0000
/* SEMI config base */
#define U300_SEMI_CONFIG_BASE 0x2FFE0000
/*
* AHB peripherals
*/
/* AHB Peripherals Bridge Controller */
#define U300_AHB_BRIDGE_BASE (U300_AHB_PER_PHYS_BASE+0x0000)
/* Vectored Interrupt Controller 0, servicing 32 interrupts */
#define U300_INTCON0_BASE (U300_AHB_PER_PHYS_BASE+0x1000)
#define U300_INTCON0_VBASE IOMEM(U300_AHB_PER_VIRT_BASE+0x1000)
/* Vectored Interrupt Controller 1, servicing 32 interrupts */
#define U300_INTCON1_BASE (U300_AHB_PER_PHYS_BASE+0x2000)
#define U300_INTCON1_VBASE IOMEM(U300_AHB_PER_VIRT_BASE+0x2000)
/* Memory Stick Pro (MSPRO) controller */
#define U300_MSPRO_BASE (U300_AHB_PER_PHYS_BASE+0x3000)
/* EMIF Configuration Area */
#define U300_EMIF_CFG_BASE (U300_AHB_PER_PHYS_BASE+0x4000)
/*
* FAST peripherals
*/
/* FAST bridge control */
#define U300_FAST_BRIDGE_BASE (U300_FAST_PER_PHYS_BASE+0x0000)
/* MMC/SD controller */
#define U300_MMCSD_BASE (U300_FAST_PER_PHYS_BASE+0x1000)
/* PCM I2S0 controller */
#define U300_PCM_I2S0_BASE (U300_FAST_PER_PHYS_BASE+0x2000)
/* PCM I2S1 controller */
#define U300_PCM_I2S1_BASE (U300_FAST_PER_PHYS_BASE+0x3000)
/* I2C0 controller */
#define U300_I2C0_BASE (U300_FAST_PER_PHYS_BASE+0x4000)
/* I2C1 controller */
#define U300_I2C1_BASE (U300_FAST_PER_PHYS_BASE+0x5000)
/* SPI controller */
#define U300_SPI_BASE (U300_FAST_PER_PHYS_BASE+0x6000)
/* Fast UART1 on U335 only */
#define U300_UART1_BASE (U300_FAST_PER_PHYS_BASE+0x7000)
/*
* SLOW peripherals
*/
/* SLOW bridge control */
#define U300_SLOW_BRIDGE_BASE (U300_SLOW_PER_PHYS_BASE)
/* SYSCON */
#define U300_SYSCON_BASE (U300_SLOW_PER_PHYS_BASE+0x1000)
#define U300_SYSCON_VBASE IOMEM(U300_SLOW_PER_VIRT_BASE+0x1000)
/* Watchdog */
#define U300_WDOG_BASE (U300_SLOW_PER_PHYS_BASE+0x2000)
/* UART0 */
#define U300_UART0_BASE (U300_SLOW_PER_PHYS_BASE+0x3000)
/* APP side special timer */
#define U300_TIMER_APP_BASE (U300_SLOW_PER_PHYS_BASE+0x4000)
#define U300_TIMER_APP_VBASE IOMEM(U300_SLOW_PER_VIRT_BASE+0x4000)
/* Keypad */
#define U300_KEYPAD_BASE (U300_SLOW_PER_PHYS_BASE+0x5000)
/* GPIO */
#define U300_GPIO_BASE (U300_SLOW_PER_PHYS_BASE+0x6000)
/* RTC */
#define U300_RTC_BASE (U300_SLOW_PER_PHYS_BASE+0x7000)
/* Bus tracer */
#define U300_BUSTR_BASE (U300_SLOW_PER_PHYS_BASE+0x8000)
/* Event handler (hardware queue) */
#define U300_EVHIST_BASE (U300_SLOW_PER_PHYS_BASE+0x9000)
/* Genric Timer */
#define U300_TIMER_BASE (U300_SLOW_PER_PHYS_BASE+0xa000)
/* PPM */
#define U300_PPM_BASE (U300_SLOW_PER_PHYS_BASE+0xb000)
/*
* REST peripherals
*/
/* ISP (image signal processor) */
#define U300_ISP_BASE (0xA0008000)
/* DMA Controller base */
#define U300_DMAC_BASE (0xC0020000)
/* MSL Base */
#define U300_MSL_BASE (0xc0022000)
/* APEX Base */
#define U300_APEX_BASE (0xc0030000)
/* Video Encoder Base */
#define U300_VIDEOENC_BASE (0xc0080000)
/* XGAM Base */
#define U300_XGAM_BASE (0xd0000000)
/*
* SYSCON addresses applicable to the core machine.
*/
/* Chip ID register 16bit (R/-) */
#define U300_SYSCON_CIDR (0x400)
/* SMCR */
#define U300_SYSCON_SMCR (0x4d0)
#define U300_SYSCON_SMCR_FIELD_MASK (0x000e)
#define U300_SYSCON_SMCR_SEMI_SREFACK_IND (0x0008)
#define U300_SYSCON_SMCR_SEMI_SREFREQ_ENABLE (0x0004)
#define U300_SYSCON_SMCR_SEMI_EXT_BOOT_MODE_ENABLE (0x0002)
/* CPU_SW_DBGEN Software Debug Enable 16bit (R/W) */
#define U300_SYSCON_CSDR (0x4f0)
#define U300_SYSCON_CSDR_SW_DEBUG_ENABLE (0x0001)
/* PRINT_CONTROL Print Control 16bit (R/-) */
#define U300_SYSCON_PCR (0x4f8)
#define U300_SYSCON_PCR_SERV_IND (0x0001)
/* BOOT_CONTROL 16bit (R/-) */
#define U300_SYSCON_BCR (0x4fc)
#define U300_SYSCON_BCR_ACC_CPU_SUBSYS_VINITHI_IND (0x0400)
#define U300_SYSCON_BCR_APP_CPU_SUBSYS_VINITHI_IND (0x0200)
#define U300_SYSCON_BCR_EXTRA_BOOT_OPTION_MASK (0x01FC)
#define U300_SYSCON_BCR_APP_BOOT_SERV_MASK (0x0003)
static void __iomem *syscon_base;
/*
* Static I/O mappings that are needed for booting the U300 platforms. The
* only things we need are the areas where we find the timer, syscon and
* intcon, since the remaining device drivers will map their own memory
* physical to virtual as the need arise.
*/
static struct map_desc u300_io_desc[] __initdata = {
{
.virtual = U300_SLOW_PER_VIRT_BASE,
.pfn = __phys_to_pfn(U300_SLOW_PER_PHYS_BASE),
.length = SZ_64K,
.type = MT_DEVICE,
},
{
.virtual = U300_AHB_PER_VIRT_BASE,
.pfn = __phys_to_pfn(U300_AHB_PER_PHYS_BASE),
.length = SZ_32K,
.type = MT_DEVICE,
},
{
.virtual = U300_FAST_PER_VIRT_BASE,
.pfn = __phys_to_pfn(U300_FAST_PER_PHYS_BASE),
.length = SZ_32K,
.type = MT_DEVICE,
},
};
static void __init u300_map_io(void)
{
iotable_init(u300_io_desc, ARRAY_SIZE(u300_io_desc));
}
static unsigned long pin_pullup_conf[] = {
PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_UP, 1),
};
static unsigned long pin_highz_conf[] = {
PIN_CONF_PACKED(PIN_CONFIG_BIAS_HIGH_IMPEDANCE, 0),
};
/* Pin control settings */
static struct pinctrl_map __initdata u300_pinmux_map[] = {
/* anonymous maps for chip power and EMIFs */
PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "power"),
PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif0"),
PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif1"),
/* per-device maps for MMC/SD, SPI and UART */
PIN_MAP_MUX_GROUP_DEFAULT("mmci", "pinctrl-u300", NULL, "mmc0"),
PIN_MAP_MUX_GROUP_DEFAULT("pl022", "pinctrl-u300", NULL, "spi0"),
PIN_MAP_MUX_GROUP_DEFAULT("uart0", "pinctrl-u300", NULL, "uart0"),
/* This pin is used for clock return rather than GPIO */
PIN_MAP_CONFIGS_PIN_DEFAULT("mmci", "pinctrl-u300", "PIO APP GPIO 11",
pin_pullup_conf),
/* This pin is used for card detect */
PIN_MAP_CONFIGS_PIN_DEFAULT("mmci", "pinctrl-u300", "PIO MS INS",
pin_highz_conf),
};
struct db_chip {
u16 chipid;
const char *name;
};
/*
* This is a list of the Digital Baseband chips used in the U300 platform.
*/
static struct db_chip db_chips[] __initdata = {
{
.chipid = 0xb800,
.name = "DB3000",
},
{
.chipid = 0xc000,
.name = "DB3100",
},
{
.chipid = 0xc800,
.name = "DB3150",
},
{
.chipid = 0xd800,
.name = "DB3200",
},
{
.chipid = 0xe000,
.name = "DB3250",
},
{
.chipid = 0xe800,
.name = "DB3210",
},
{
.chipid = 0xf000,
.name = "DB3350 P1x",
},
{
.chipid = 0xf100,
.name = "DB3350 P2x",
},
{
.chipid = 0x0000, /* List terminator */
.name = NULL,
}
};
static void __init u300_init_check_chip(void)
{
u16 val;
struct db_chip *chip;
const char *chipname;
const char unknown[] = "UNKNOWN";
/* Read out and print chip ID */
val = readw(syscon_base + U300_SYSCON_CIDR);
/* This is in funky bigendian order... */
val = (val & 0xFFU) << 8 | (val >> 8);
chip = db_chips;
chipname = unknown;
for ( ; chip->chipid; chip++) {
if (chip->chipid == (val & 0xFF00U)) {
chipname = chip->name;
break;
}
}
printk(KERN_INFO "Initializing U300 system on %s baseband chip " \
"(chip ID 0x%04x)\n", chipname, val);
if ((val & 0xFF00U) != 0xf000 && (val & 0xFF00U) != 0xf100) {
printk(KERN_ERR "Platform configured for BS335 " \
" with DB3350 but %s detected, expect problems!",
chipname);
}
}
/* Forward declare this function from the watchdog */
void coh901327_watchdog_reset(void);
static void u300_restart(enum reboot_mode mode, const char *cmd)
{
switch (mode) {
case REBOOT_SOFT:
case REBOOT_HARD:
#ifdef CONFIG_COH901327_WATCHDOG
coh901327_watchdog_reset();
#endif
break;
default:
/* Do nothing */
break;
}
/* Wait for system do die/reset. */
while (1);
}
/* These are mostly to get the right device names for the clock lookups */
static struct of_dev_auxdata u300_auxdata_lookup[] __initdata = {
OF_DEV_AUXDATA("stericsson,pinctrl-u300", U300_SYSCON_BASE,
"pinctrl-u300", NULL),
OF_DEV_AUXDATA("stericsson,gpio-coh901", U300_GPIO_BASE,
"u300-gpio", NULL),
OF_DEV_AUXDATA("stericsson,coh901327", U300_WDOG_BASE,
"coh901327_wdog", NULL),
OF_DEV_AUXDATA("stericsson,coh901331", U300_RTC_BASE,
"rtc-coh901331", NULL),
OF_DEV_AUXDATA("stericsson,coh901318", U300_DMAC_BASE,
"coh901318", NULL),
OF_DEV_AUXDATA("stericsson,fsmc-nand", U300_NAND_IF_PHYS_BASE,
"fsmc-nand", NULL),
OF_DEV_AUXDATA("arm,primecell", U300_UART0_BASE,
"uart0", NULL),
OF_DEV_AUXDATA("arm,primecell", U300_UART1_BASE,
"uart1", NULL),
OF_DEV_AUXDATA("arm,primecell", U300_SPI_BASE,
"pl022", NULL),
OF_DEV_AUXDATA("st,ddci2c", U300_I2C0_BASE,
"stu300.0", NULL),
OF_DEV_AUXDATA("st,ddci2c", U300_I2C1_BASE,
"stu300.1", NULL),
OF_DEV_AUXDATA("arm,primecell", U300_MMCSD_BASE,
"mmci", NULL),
{ /* sentinel */ },
};
static void __init u300_init_irq_dt(void)
{
struct device_node *syscon;
struct clk *clk;
syscon = of_find_node_by_path("/syscon@c0011000");
if (!syscon) {
pr_crit("could not find syscon node\n");
return;
}
syscon_base = of_iomap(syscon, 0);
if (!syscon_base) {
pr_crit("could not remap syscon\n");
return;
}
/* initialize clocking early, we want to clock the INTCON */
u300_clk_init(syscon_base);
/* Bootstrap EMIF and SEMI clocks */
clk = clk_get_sys("pl172", NULL);
BUG_ON(IS_ERR(clk));
clk_prepare_enable(clk);
clk = clk_get_sys("semi", NULL);
BUG_ON(IS_ERR(clk));
clk_prepare_enable(clk);
/* Clock the interrupt controller */
clk = clk_get_sys("intcon", NULL);
BUG_ON(IS_ERR(clk));
clk_prepare_enable(clk);
irqchip_init();
}
static void __init u300_init_machine_dt(void)
{
u16 val;
/* Check what platform we run and print some status information */
u300_init_check_chip();
/* Initialize pinmuxing */
pinctrl_register_mappings(u300_pinmux_map,
ARRAY_SIZE(u300_pinmux_map));
of_platform_default_populate(NULL, u300_auxdata_lookup, NULL);
/* Enable SEMI self refresh */
val = readw(syscon_base + U300_SYSCON_SMCR) |
U300_SYSCON_SMCR_SEMI_SREFREQ_ENABLE;
writew(val, syscon_base + U300_SYSCON_SMCR);
}
static const char * u300_board_compat[] = {
"stericsson,u300",
NULL,
};
DT_MACHINE_START(U300_DT, "U300 S335/B335 (Device Tree)")
.map_io = u300_map_io,
.init_irq = u300_init_irq_dt,
.init_time = timer_probe,
.init_machine = u300_init_machine_dt,
.restart = u300_restart,
.dt_compat = u300_board_compat,
MACHINE_END
