/*
*
* BRIEF MODULE DESCRIPTION
* Cogent CSB250 board setup.
*
* Copyright 2002 Cogent Computer Systems, Inc.
* dan@embeddededge.com
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/config.h>
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/ioport.h>
#include <linux/mm.h>
#include <linux/console.h>
#include <linux/mc146818rtc.h>
#include <linux/delay.h>
#include <asm/cpu.h>
#include <asm/bootinfo.h>
#include <asm/irq.h>
#include <asm/keyboard.h>
#include <asm/mipsregs.h>
#include <asm/reboot.h>
#include <asm/pgtable.h>
#include <asm/au1000.h>
#include <asm/csb250.h>
extern int (*board_pci_idsel)(unsigned int devsel, int assert);
int csb250_pci_idsel(unsigned int devsel, int assert);
void __init board_setup(void)
{
u32 pin_func, pin_val;
u32 sys_freqctrl, sys_clksrc;
// set AUX clock to 12MHz * 8 = 96 MHz
au_writel(8, SYS_AUXPLL);
au_writel(0, SYS_PINSTATERD);
udelay(100);
#if defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE)
/* GPIO201 is input for PCMCIA card detect */
/* GPIO203 is input for PCMCIA interrupt request */
au_writel(au_readl(GPIO2_DIR) & (u32)(~((1<<1)|(1<<3))), GPIO2_DIR);
/* zero and disable FREQ2 */
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/* zero and disable USBH/USBD clocks */
sys_clksrc = au_readl(SYS_CLKSRC);
sys_clksrc &= ~0x00007FE0;
au_writel(sys_clksrc, SYS_CLKSRC);
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
sys_clksrc = au_readl(SYS_CLKSRC);
sys_clksrc &= ~0x00007FE0;
// FREQ2 = aux/2 = 48 MHz
sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/*
* Route 48MHz FREQ2 into USB Host and/or Device
*/
#ifdef CONFIG_USB_OHCI
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
#endif
#ifdef CONFIG_AU1X00_USB_DEVICE
sys_clksrc |= ((4<<7) | (0<<6) | (0<<5));
#endif
au_writel(sys_clksrc, SYS_CLKSRC);
pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000);
#ifndef CONFIG_AU1X00_USB_DEVICE
// 2nd USB port is USB host
pin_func |= 0x8000;
#endif
au_writel(pin_func, SYS_PINFUNC);
#endif // defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE)
/* Configure GPIO2....it's used by PCI among other things.
*/
/* Make everything but GP200 (PCI RST) an input until we get
* the pins set correctly.
*/
au_writel(0x00000001, GPIO2_DIR);
/* Set the pins used for output.
* A zero bit will leave PCI reset, LEDs off, power up USB,
* IDSEL disabled.
*/
pin_val = ((3 << 30) | (7 << 19) | (1 << 17) | (1 << 16));
au_writel(pin_val, GPIO2_OUTPUT);
/* Set the output direction.
*/
pin_val = ((3 << 14) | (7 << 3) | (1 << 1) | (1 << 0));
au_writel(pin_val, GPIO2_DIR);
#ifdef CONFIG_PCI
/* Use FREQ1 for the PCI output clock. We use the
* CPU clock of 384 MHz divided by 12 to get 32 MHz PCI.
* If Michael changes the CPU speed, we need to adjust
* that here as well :-).
*/
/* zero and disable FREQ1
*/
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0x000ffc00;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/* zero and disable PCI clock
*/
sys_clksrc = au_readl(SYS_CLKSRC);
sys_clksrc &= ~0x000f8000;
au_writel(sys_clksrc, SYS_CLKSRC);
/* Get current values (which really should match above).
*/
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0x000ffc00;
sys_clksrc = au_readl(SYS_CLKSRC);
sys_clksrc &= ~0x000f8000;
/* FREQ1 = cpu/12 = 32 MHz
*/
sys_freqctrl |= ((5<<12) | (1<<11) | (0<<10));
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/* Just connect the clock without further dividing.
*/
sys_clksrc |= ((3<<17) | (0<<16) | (0<<15));
au_writel(sys_clksrc, SYS_CLKSRC);
udelay(1);
/* Now that clocks should be running, take PCI out of reset.
*/
pin_val = au_readl(GPIO2_OUTPUT);
pin_val |= ((1 << 16) | 1);
au_writel(pin_val, GPIO2_OUTPUT);
// Setup PCI bus controller
au_writel(0, Au1500_PCI_CMEM);
au_writel(0x00003fff, Au1500_CFG_BASE);
/* We run big endian without any of the software byte swapping,
* so configure the PCI bridge to help us out.
*/
au_writel(0xf | (2<<6) | (1<<5) | (1<<4), Au1500_PCI_CFG);
au_writel(0xf0000000, Au1500_PCI_MWMASK_DEV);
au_writel(0, Au1500_PCI_MWBASE_REV_CCL);
au_writel(0x02a00356, Au1500_PCI_STATCMD);
au_writel(0x00003c04, Au1500_PCI_HDRTYPE);
au_writel(0x00000008, Au1500_PCI_MBAR);
au_sync();
board_pci_idsel = csb250_pci_idsel;
#endif
/* Enable sys bus clock divider when IDLE state or no bus activity. */
au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
#ifdef CONFIG_RTC
// Enable the RTC if not already enabled
if (!(au_readl(0xac000028) & 0x20)) {
printk("enabling clock ...\n");
au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
}
// Put the clock in BCD mode
if (readl(0xac00002C) & 0x4) { /* reg B */
au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
au_sync();
}
#endif
}
/* The IDSEL is selected in the GPIO2 register. We will make device
* 12 appear in slot 0 and device 13 appear in slot 1.
*/
int
csb250_pci_idsel(unsigned int devsel, int assert)
{
int retval;
unsigned int gpio2_pins;
retval = 1;
/* First, disable both selects, then assert the one requested.
*/
au_writel(0xc000c000, GPIO2_OUTPUT);
au_sync();
if (assert) {
if (devsel == 12)
gpio2_pins = 0x40000000;
else if (devsel == 13)
gpio2_pins = 0x80000000;
else {
gpio2_pins = 0xc000c000;
retval = 0;
}
au_writel(gpio2_pins, GPIO2_OUTPUT);
}
au_sync();
return retval;
}
