/*
* pata_piccolo.c - Toshiba Piccolo PATA/SATA controller driver.
*
* This is basically an update to ata_generic.c to add Toshiba Piccolo support
* then split out to keep ata_generic "clean".
*
* Copyright 2005 Red Hat Inc, all rights reserved.
*
* Elements from ide/pci/generic.c
* Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org>
* Portions (C) Copyright 2002 Red Hat Inc <alan@redhat.com>
*
* May be copied or modified under the terms of the GNU General Public License
*
* The timing data tables/programming info are courtesy of the NetBSD driver
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_piccolo"
#define DRV_VERSION "0.0.1"
static void tosh_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
static const u16 pio[6] = { /* For reg 0x50 low word & E088 */
0x0566, 0x0433, 0x0311, 0x0201, 0x0200, 0x0100
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u16 conf;
pci_read_config_word(pdev, 0x50, &conf);
conf &= 0xE088;
conf |= pio[adev->pio_mode - XFER_PIO_0];
pci_write_config_word(pdev, 0x50, conf);
}
static void tosh_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 conf;
pci_read_config_dword(pdev, 0x5C, &conf);
conf &= 0x78FFE088; /* Keep the other bits */
if (adev->dma_mode >= XFER_UDMA_0) {
int udma = adev->dma_mode - XFER_UDMA_0;
conf |= 0x80000000;
conf |= (udma + 2) << 28;
conf |= (2 - udma) * 0x111; /* spread into three nibbles */
} else {
static const u32 mwdma[4] = {
0x0655, 0x0200, 0x0200, 0x0100
};
conf |= mwdma[adev->dma_mode - XFER_MW_DMA_0];
}
pci_write_config_dword(pdev, 0x5C, conf);
}
static struct scsi_host_template tosh_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
static struct ata_port_operations tosh_port_ops = {
.inherits = &ata_bmdma_port_ops,
.cable_detect = ata_cable_unknown,
.set_piomode = tosh_set_piomode,
.set_dmamode = tosh_set_dmamode
};
/**
* ata_tosh_init - attach generic IDE
* @dev: PCI device found
* @id: match entry
*
* Called each time a matching IDE interface is found. We check if the
* interface is one we wish to claim and if so we perform any chip
* specific hacks then let the ATA layer do the heavy lifting.
*/
static int ata_tosh_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
.port_ops = &tosh_port_ops
};
const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
/* Just one port for the moment */
return ata_pci_bmdma_init_one(dev, ppi, &tosh_sht, NULL, 0);
}
static struct pci_device_id ata_tosh[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), },
{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), },
{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_3), },
{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_5), },
{ 0, },
};
static struct pci_driver ata_tosh_pci_driver = {
.name = DRV_NAME,
.id_table = ata_tosh,
.probe = ata_tosh_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM_SLEEP
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
#endif
};
module_pci_driver(ata_tosh_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("Low level driver for Toshiba Piccolo ATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, ata_tosh);
MODULE_VERSION(DRV_VERSION);
