/*
* Copyright © 2006-2007 Intel Corporation
*
* Permission is hereby granted, free of charge, to any person obtaining a
* copy of this software and associated documentation files (the "Software"),
* to deal in the Software without restriction, including without limitation
* the rights to use, copy, modify, merge, publish, distribute, sublicense,
* and/or sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice (including the next
* paragraph) shall be included in all copies or substantial portions of the
* Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
* DEALINGS IN THE SOFTWARE.
*
* Authors:
* Eric Anholt <eric@anholt.net>
*/
#include <linux/i2c.h>
#include "drmP.h"
#include "drm.h"
#include "drm_crtc.h"
#include "drm_crtc_helper.h"
#include "intel_drv.h"
#include "i915_drm.h"
#include "i915_drv.h"
static void intel_crt_dpms(struct drm_encoder *encoder, int mode)
{
struct drm_device *dev = encoder->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
u32 temp, reg;
if (IS_IGDNG(dev))
reg = PCH_ADPA;
else
reg = ADPA;
temp = I915_READ(reg);
temp &= ~(ADPA_HSYNC_CNTL_DISABLE | ADPA_VSYNC_CNTL_DISABLE);
temp &= ~ADPA_DAC_ENABLE;
switch(mode) {
case DRM_MODE_DPMS_ON:
temp |= ADPA_DAC_ENABLE;
break;
case DRM_MODE_DPMS_STANDBY:
temp |= ADPA_DAC_ENABLE | ADPA_HSYNC_CNTL_DISABLE;
break;
case DRM_MODE_DPMS_SUSPEND:
temp |= ADPA_DAC_ENABLE | ADPA_VSYNC_CNTL_DISABLE;
break;
case DRM_MODE_DPMS_OFF:
temp |= ADPA_HSYNC_CNTL_DISABLE | ADPA_VSYNC_CNTL_DISABLE;
break;
}
I915_WRITE(reg, temp);
if (IS_IGD(dev)) {
if (mode == DRM_MODE_DPMS_OFF) {
/* turn off DAC */
temp = I915_READ(PORT_HOTPLUG_EN);
temp &= ~CRT_EOS_INT_EN;
I915_WRITE(PORT_HOTPLUG_EN, temp);
temp = I915_READ(PORT_HOTPLUG_STAT);
if (temp & CRT_EOS_INT_STATUS)
I915_WRITE(PORT_HOTPLUG_STAT,
CRT_EOS_INT_STATUS);
} else {
/* turn on DAC. EOS interrupt must be enabled after DAC
* is enabled, so it sounds not good to enable it in
* i915_driver_irq_postinstall()
* wait 12.5ms after DAC is enabled
*/
msleep(13);
temp = I915_READ(PORT_HOTPLUG_STAT);
if (temp & CRT_EOS_INT_STATUS)
I915_WRITE(PORT_HOTPLUG_STAT,
CRT_EOS_INT_STATUS);
temp = I915_READ(PORT_HOTPLUG_EN);
temp |= CRT_EOS_INT_EN;
I915_WRITE(PORT_HOTPLUG_EN, temp);
}
}
}
static int intel_crt_mode_valid(struct drm_connector *connector,
struct drm_display_mode *mode)
{
struct drm_device *dev = connector->dev;
int max_clock = 0;
if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
return MODE_NO_DBLESCAN;
if (mode->clock < 25000)
return MODE_CLOCK_LOW;
if (!IS_I9XX(dev))
max_clock = 350000;
else
max_clock = 400000;
if (mode->clock > max_clock)
return MODE_CLOCK_HIGH;
return MODE_OK;
}
static bool intel_crt_mode_fixup(struct drm_encoder *encoder,
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode)
{
return true;
}
static void intel_crt_mode_set(struct drm_encoder *encoder,
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode)
{
struct drm_device *dev = encoder->dev;
struct drm_crtc *crtc = encoder->crtc;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
struct drm_i915_private *dev_priv = dev->dev_private;
int dpll_md_reg;
u32 adpa, dpll_md;
u32 adpa_reg;
if (intel_crtc->pipe == 0)
dpll_md_reg = DPLL_A_MD;
else
dpll_md_reg = DPLL_B_MD;
if (IS_IGDNG(dev))
adpa_reg = PCH_ADPA;
else
adpa_reg = ADPA;
/*
* Disable separate mode multiplier used when cloning SDVO to CRT
* XXX this needs to be adjusted when we really are cloning
*/
if (IS_I965G(dev) && !IS_IGDNG(dev)) {
dpll_md = I915_READ(dpll_md_reg);
I915_WRITE(dpll_md_reg,
dpll_md & ~DPLL_MD_UDI_MULTIPLIER_MASK);
}
adpa = 0;
if (adjusted_mode->flags & DRM_MODE_FLAG_PHSYNC)
adpa |= ADPA_HSYNC_ACTIVE_HIGH;
if (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC)
adpa |= ADPA_VSYNC_ACTIVE_HIGH;
if (intel_crtc->pipe == 0) {
adpa |= ADPA_PIPE_A_SELECT;
if (!IS_IGDNG(dev))
I915_WRITE(BCLRPAT_A, 0);
} else {
adpa |= ADPA_PIPE_B_SELECT;
if (!IS_IGDNG(dev))
I915_WRITE(BCLRPAT_B, 0);
}
I915_WRITE(adpa_reg, adpa);
}
static bool intel_igdng_crt_detect_hotplug(struct drm_connector *connector)
{
struct drm_device *dev = connector->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
u32 adpa, temp;
bool ret;
temp = adpa = I915_READ(PCH_ADPA);
adpa &= ~ADPA_DAC_ENABLE;
I915_WRITE(PCH_ADPA, adpa);
adpa &= ~ADPA_CRT_HOTPLUG_MASK;
adpa |= (ADPA_CRT_HOTPLUG_PERIOD_128 |
ADPA_CRT_HOTPLUG_WARMUP_10MS |
ADPA_CRT_HOTPLUG_SAMPLE_4S |
ADPA_CRT_HOTPLUG_VOLTAGE_50 | /* default */
ADPA_CRT_HOTPLUG_VOLREF_325MV |
ADPA_CRT_HOTPLUG_ENABLE |
ADPA_CRT_HOTPLUG_FORCE_TRIGGER);
DRM_DEBUG("pch crt adpa 0x%x", adpa);
I915_WRITE(PCH_ADPA, adpa);
while ((I915_READ(PCH_ADPA) & ADPA_CRT_HOTPLUG_FORCE_TRIGGER) != 0)
;
/* Check the status to see if both blue and green are on now */
adpa = I915_READ(PCH_ADPA);
adpa &= ADPA_CRT_HOTPLUG_MONITOR_MASK;
if ((adpa == ADPA_CRT_HOTPLUG_MONITOR_COLOR) ||
(adpa == ADPA_CRT_HOTPLUG_MONITOR_MONO))
ret = true;
else
ret = false;
/* restore origin register */
I915_WRITE(PCH_ADPA, temp);
return ret;
}
/**
* Uses CRT_HOTPLUG_EN and CRT_HOTPLUG_STAT to detect CRT presence.
*
* Not for i915G/i915GM
*
* \return true if CRT is connected.
* \return false if CRT is disconnected.
*/
static bool intel_crt_detect_hotplug(struct drm_connector *connector)
{
struct drm_device *dev = connector->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
u32 hotplug_en;
int i, tries = 0;
if (IS_IGDNG(dev))
return intel_igdng_crt_detect_hotplug(connector);
/*
* On 4 series desktop, CRT detect sequence need to be done twice
* to get a reliable result.
*/
if (IS_G4X(dev) && !IS_GM45(dev))
tries = 2;
else
tries = 1;
hotplug_en = I915_READ(PORT_HOTPLUG_EN);
hotplug_en &= CRT_FORCE_HOTPLUG_MASK;
hotplug_en |= CRT_HOTPLUG_FORCE_DETECT;
if (IS_G4X(dev))
hotplug_en |= CRT_HOTPLUG_ACTIVATION_PERIOD_64;
hotplug_en |= CRT_HOTPLUG_VOLTAGE_COMPARE_50;
for (i = 0; i < tries ; i++) {
unsigned long timeout;
/* turn on the FORCE_DETECT */
I915_WRITE(PORT_HOTPLUG_EN, hotplug_en);
timeout = jiffies + msecs_to_jiffies(1000);
/* wait for FORCE_DETECT to go off */
do {
if (!(I915_READ(PORT_HOTPLUG_EN) &
CRT_HOTPLUG_FORCE_DETECT))
break;
msleep(1);
} while (time_after(timeout, jiffies));
}
if ((I915_READ(PORT_HOTPLUG_STAT) & CRT_HOTPLUG_MONITOR_MASK) ==
CRT_HOTPLUG_MONITOR_COLOR)
return true;
return false;
}
static bool intel_crt_detect_ddc(struct drm_connector *connector)
{
struct intel_output *intel_output = to_intel_output(connector);
/* CRT should always be at 0, but check anyway */
if (intel_output->type != INTEL_OUTPUT_ANALOG)
return false;
return intel_ddc_probe(intel_output);
}
static enum drm_connector_status
intel_crt_load_detect(struct drm_crtc *crtc, struct intel_output *intel_output)
{
struct drm_encoder *encoder = &intel_output->enc;
struct drm_device *dev = encoder->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
uint32_t pipe = intel_crtc->pipe;
uint32_t save_bclrpat;
uint32_t save_vtotal;
uint32_t vtotal, vactive;
uint32_t vsample;
uint32_t vblank, vblank_start, vblank_end;
uint32_t dsl;
uint32_t bclrpat_reg;
uint32_t vtotal_reg;
uint32_t vblank_reg;
uint32_t vsync_reg;
uint32_t pipeconf_reg;
uint32_t pipe_dsl_reg;
uint8_t st00;
enum drm_connector_status status;
if (pipe == 0) {
bclrpat_reg = BCLRPAT_A;
vtotal_reg = VTOTAL_A;
vblank_reg = VBLANK_A;
vsync_reg = VSYNC_A;
pipeconf_reg = PIPEACONF;
pipe_dsl_reg = PIPEADSL;
} else {
bclrpat_reg = BCLRPAT_B;
vtotal_reg = VTOTAL_B;
vblank_reg = VBLANK_B;
vsync_reg = VSYNC_B;
pipeconf_reg = PIPEBCONF;
pipe_dsl_reg = PIPEBDSL;
}
save_bclrpat = I915_READ(bclrpat_reg);
save_vtotal = I915_READ(vtotal_reg);
vblank = I915_READ(vblank_reg);
vtotal = ((save_vtotal >> 16) & 0xfff) + 1;
vactive = (save_vtotal & 0x7ff) + 1;
vblank_start = (vblank & 0xfff) + 1;
vblank_end = ((vblank >> 16) & 0xfff) + 1;
/* Set the border color to purple. */
I915_WRITE(bclrpat_reg, 0x500050);
if (IS_I9XX(dev)) {
uint32_t pipeconf = I915_READ(pipeconf_reg);
I915_WRITE(pipeconf_reg, pipeconf | PIPECONF_FORCE_BORDER);
/* Wait for next Vblank to substitue
* border color for Color info */
intel_wait_for_vblank(dev);
st00 = I915_READ8(VGA_MSR_WRITE);
status = ((st00 & (1 << 4)) != 0) ?
connector_status_connected :
connector_status_disconnected;
I915_WRITE(pipeconf_reg, pipeconf);
} else {
bool restore_vblank = false;
int count, detect;
/*
* If there isn't any border, add some.
* Yes, this will flicker
*/
if (vblank_start <= vactive && vblank_end >= vtotal) {
uint32_t vsync = I915_READ(vsync_reg);
uint32_t vsync_start = (vsync & 0xffff) + 1;
vblank_start = vsync_start;
I915_WRITE(vblank_reg,
(vblank_start - 1) |
((vblank_end - 1) << 16));
restore_vblank = true;
}
/* sample in the vertical border, selecting the larger one */
if (vblank_start - vactive >= vtotal - vblank_end)
vsample = (vblank_start + vactive) >> 1;
else
vsample = (vtotal + vblank_end) >> 1;
/*
* Wait for the border to be displayed
*/
while (I915_READ(pipe_dsl_reg) >= vactive)
;
while ((dsl = I915_READ(pipe_dsl_reg)) <= vsample)
;
/*
* Watch ST00 for an entire scanline
*/
detect = 0;
count = 0;
do {
count++;
/* Read the ST00 VGA status register */
st00 = I915_READ8(VGA_MSR_WRITE);
if (st00 & (1 << 4))
detect++;
} while ((I915_READ(pipe_dsl_reg) == dsl));
/* restore vblank if necessary */
if (restore_vblank)
I915_WRITE(vblank_reg, vblank);
/*
* If more than 3/4 of the scanline detected a monitor,
* then it is assumed to be present. This works even on i830,
* where there isn't any way to force the border color across
* the screen
*/
status = detect * 4 > count * 3 ?
connector_status_connected :
connector_status_disconnected;
}
/* Restore previous settings */
I915_WRITE(bclrpat_reg, save_bclrpat);
return status;
}
static enum drm_connector_status intel_crt_detect(struct drm_connector *connector)
{
struct drm_device *dev = connector->dev;
struct intel_output *intel_output = to_intel_output(connector);
struct drm_encoder *encoder = &intel_output->enc;
struct drm_crtc *crtc;
int dpms_mode;
enum drm_connector_status status;
if (IS_I9XX(dev) && !IS_I915G(dev) && !IS_I915GM(dev)) {
if (intel_crt_detect_hotplug(connector))
return connector_status_connected;
else
return connector_status_disconnected;
}
if (intel_crt_detect_ddc(connector))
return connector_status_connected;
/* for pre-945g platforms use load detect */
if (encoder->crtc && encoder->crtc->enabled) {
status = intel_crt_load_detect(encoder->crtc, intel_output);
} else {
crtc = intel_get_load_detect_pipe(intel_output,
NULL, &dpms_mode);
if (crtc) {
status = intel_crt_load_detect(crtc, intel_output);
intel_release_load_detect_pipe(intel_output, dpms_mode);
} else
status = connector_status_unknown;
}
return status;
}
static void intel_crt_destroy(struct drm_connector *connector)
{
struct intel_output *intel_output = to_intel_output(connector);
intel_i2c_destroy(intel_output->ddc_bus);
drm_sysfs_connector_remove(connector);
drm_connector_cleanup(connector);
kfree(connector);
}
static int intel_crt_get_modes(struct drm_connector *connector)
{
int ret;
struct intel_output *intel_output = to_intel_output(connector);
struct i2c_adapter *ddcbus;
struct drm_device *dev = connector->dev;
ret = intel_ddc_get_modes(intel_output);
if (ret || !IS_G4X(dev))
goto end;
ddcbus = intel_output->ddc_bus;
/* Try to probe digital port for output in DVI-I -> VGA mode. */
intel_output->ddc_bus =
intel_i2c_create(connector->dev, GPIOD, "CRTDDC_D");
if (!intel_output->ddc_bus) {
intel_output->ddc_bus = ddcbus;
dev_printk(KERN_ERR, &connector->dev->pdev->dev,
"DDC bus registration failed for CRTDDC_D.\n");
goto end;
}
/* Try to get modes by GPIOD port */
ret = intel_ddc_get_modes(intel_output);
intel_i2c_destroy(ddcbus);
end:
return ret;
}
static int intel_crt_set_property(struct drm_connector *connector,
struct drm_property *property,
uint64_t value)
{
return 0;
}
/*
* Routines for controlling stuff on the analog port
*/
static const struct drm_encoder_helper_funcs intel_crt_helper_funcs = {
.dpms = intel_crt_dpms,
.mode_fixup = intel_crt_mode_fixup,
.prepare = intel_encoder_prepare,
.commit = intel_encoder_commit,
.mode_set = intel_crt_mode_set,
};
static const struct drm_connector_funcs intel_crt_connector_funcs = {
.dpms = drm_helper_connector_dpms,
.detect = intel_crt_detect,
.fill_modes = drm_helper_probe_single_connector_modes,
.destroy = intel_crt_destroy,
.set_property = intel_crt_set_property,
};
static const struct drm_connector_helper_funcs intel_crt_connector_helper_funcs = {
.mode_valid = intel_crt_mode_valid,
.get_modes = intel_crt_get_modes,
.best_encoder = intel_best_encoder,
};
static void intel_crt_enc_destroy(struct drm_encoder *encoder)
{
drm_encoder_cleanup(encoder);
}
static const struct drm_encoder_funcs intel_crt_enc_funcs = {
.destroy = intel_crt_enc_destroy,
};
void intel_crt_init(struct drm_device *dev)
{
struct drm_connector *connector;
struct intel_output *intel_output;
struct drm_i915_private *dev_priv = dev->dev_private;
u32 i2c_reg;
intel_output = kzalloc(sizeof(struct intel_output), GFP_KERNEL);
if (!intel_output)
return;
connector = &intel_output->base;
drm_connector_init(dev, &intel_output->base,
&intel_crt_connector_funcs, DRM_MODE_CONNECTOR_VGA);
drm_encoder_init(dev, &intel_output->enc, &intel_crt_enc_funcs,
DRM_MODE_ENCODER_DAC);
drm_mode_connector_attach_encoder(&intel_output->base,
&intel_output->enc);
/* Set up the DDC bus. */
if (IS_IGDNG(dev))
i2c_reg = PCH_GPIOA;
else {
i2c_reg = GPIOA;
/* Use VBT information for CRT DDC if available */
if (dev_priv->crt_ddc_bus != -1)
i2c_reg = dev_priv->crt_ddc_bus;
}
intel_output->ddc_bus = intel_i2c_create(dev, i2c_reg, "CRTDDC_A");
if (!intel_output->ddc_bus) {
dev_printk(KERN_ERR, &dev->pdev->dev, "DDC bus registration "
"failed.\n");
return;
}
intel_output->type = INTEL_OUTPUT_ANALOG;
intel_output->clone_mask = (1 << INTEL_SDVO_NON_TV_CLONE_BIT) |
(1 << INTEL_ANALOG_CLONE_BIT) |
(1 << INTEL_SDVO_LVDS_CLONE_BIT);
intel_output->crtc_mask = (1 << 0) | (1 << 1);
connector->interlace_allowed = 0;
connector->doublescan_allowed = 0;
drm_encoder_helper_add(&intel_output->enc, &intel_crt_helper_funcs);
drm_connector_helper_add(connector, &intel_crt_connector_helper_funcs);
drm_sysfs_connector_add(connector);
}
