/*
* w83793.c - Linux kernel driver for hardware monitoring
* Copyright (C) 2006 Winbond Electronics Corp.
* Yuan Mu
* Rudolf Marek <r.marek@assembler.cz>
* Copyright (C) 2009-2010 Sven Anders <anders@anduras.de>, ANDURAS AG.
* Watchdog driver part
* (Based partially on fschmd driver,
* Copyright 2007-2008 by Hans de Goede)
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation - version 2.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
* 02110-1301 USA.
*/
/*
* Supports following chips:
*
* Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA
* w83793 10 12 8 6 0x7b 0x5ca3 yes no
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-vid.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>
#include <linux/fs.h>
#include <linux/watchdog.h>
#include <linux/miscdevice.h>
#include <linux/uaccess.h>
#include <linux/kref.h>
#include <linux/notifier.h>
#include <linux/reboot.h>
#include <linux/jiffies.h>
/* Default values */
#define WATCHDOG_TIMEOUT 2 /* 2 minute default timeout */
/* Addresses to scan */
static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
I2C_CLIENT_END };
/* Insmod parameters */
static unsigned short force_subclients[4];
module_param_array(force_subclients, short, NULL, 0);
MODULE_PARM_DESC(force_subclients,
"List of subclient addresses: {bus, clientaddr, subclientaddr1, subclientaddr2}");
static bool reset;
module_param(reset, bool, 0);
MODULE_PARM_DESC(reset, "Set to 1 to reset chip, not recommended");
static int timeout = WATCHDOG_TIMEOUT; /* default timeout in minutes */
module_param(timeout, int, 0);
MODULE_PARM_DESC(timeout,
"Watchdog timeout in minutes. 2<= timeout <=255 (default="
__MODULE_STRING(WATCHDOG_TIMEOUT) ")");
static bool nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, bool, 0);
MODULE_PARM_DESC(nowayout,
"Watchdog cannot be stopped once started (default="
__MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Address 0x00, 0x0d, 0x0e, 0x0f in all three banks are reserved
* as ID, Bank Select registers
*/
#define W83793_REG_BANKSEL 0x00
#define W83793_REG_VENDORID 0x0d
#define W83793_REG_CHIPID 0x0e
#define W83793_REG_DEVICEID 0x0f
#define W83793_REG_CONFIG 0x40
#define W83793_REG_MFC 0x58
#define W83793_REG_FANIN_CTRL 0x5c
#define W83793_REG_FANIN_SEL 0x5d
#define W83793_REG_I2C_ADDR 0x0b
#define W83793_REG_I2C_SUBADDR 0x0c
#define W83793_REG_VID_INA 0x05
#define W83793_REG_VID_INB 0x06
#define W83793_REG_VID_LATCHA 0x07
#define W83793_REG_VID_LATCHB 0x08
#define W83793_REG_VID_CTRL 0x59
#define W83793_REG_WDT_LOCK 0x01
#define W83793_REG_WDT_ENABLE 0x02
#define W83793_REG_WDT_STATUS 0x03
#define W83793_REG_WDT_TIMEOUT 0x04
static u16 W83793_REG_TEMP_MODE[2] = { 0x5e, 0x5f };
#define TEMP_READ 0
#define TEMP_CRIT 1
#define TEMP_CRIT_HYST 2
#define TEMP_WARN 3
#define TEMP_WARN_HYST 4
/*
* only crit and crit_hyst affect real-time alarm status
* current crit crit_hyst warn warn_hyst
*/
static u16 W83793_REG_TEMP[][5] = {
{0x1c, 0x78, 0x79, 0x7a, 0x7b},
{0x1d, 0x7c, 0x7d, 0x7e, 0x7f},
{0x1e, 0x80, 0x81, 0x82, 0x83},
{0x1f, 0x84, 0x85, 0x86, 0x87},
{0x20, 0x88, 0x89, 0x8a, 0x8b},
{0x21, 0x8c, 0x8d, 0x8e, 0x8f},
};
#define W83793_REG_TEMP_LOW_BITS 0x22
#define W83793_REG_BEEP(index) (0x53 + (index))
#define W83793_REG_ALARM(index) (0x4b + (index))
#define W83793_REG_CLR_CHASSIS 0x4a /* SMI MASK4 */
#define W83793_REG_IRQ_CTRL 0x50
#define W83793_REG_OVT_CTRL 0x51
#define W83793_REG_OVT_BEEP 0x52
#define IN_READ 0
#define IN_MAX 1
#define IN_LOW 2
static const u16 W83793_REG_IN[][3] = {
/* Current, High, Low */
{0x10, 0x60, 0x61}, /* Vcore A */
{0x11, 0x62, 0x63}, /* Vcore B */
{0x12, 0x64, 0x65}, /* Vtt */
{0x14, 0x6a, 0x6b}, /* VSEN1 */
{0x15, 0x6c, 0x6d}, /* VSEN2 */
{0x16, 0x6e, 0x6f}, /* +3VSEN */
{0x17, 0x70, 0x71}, /* +12VSEN */
{0x18, 0x72, 0x73}, /* 5VDD */
{0x19, 0x74, 0x75}, /* 5VSB */
{0x1a, 0x76, 0x77}, /* VBAT */
};
/* Low Bits of Vcore A/B Vtt Read/High/Low */
static const u16 W83793_REG_IN_LOW_BITS[] = { 0x1b, 0x68, 0x69 };
static u8 scale_in[] = { 2, 2, 2, 16, 16, 16, 8, 24, 24, 16 };
static u8 scale_in_add[] = { 0, 0, 0, 0, 0, 0, 0, 150, 150, 0 };
#define W83793_REG_FAN(index) (0x23 + 2 * (index)) /* High byte */
#define W83793_REG_FAN_MIN(index) (0x90 + 2 * (index)) /* High byte */
#define W83793_REG_PWM_DEFAULT 0xb2
#define W83793_REG_PWM_ENABLE 0x207
#define W83793_REG_PWM_UPTIME 0xc3 /* Unit in 0.1 second */
#define W83793_REG_PWM_DOWNTIME 0xc4 /* Unit in 0.1 second */
#define W83793_REG_TEMP_CRITICAL 0xc5
#define PWM_DUTY 0
#define PWM_START 1
#define PWM_NONSTOP 2
#define PWM_STOP_TIME 3
#define W83793_REG_PWM(index, nr) (((nr) == 0 ? 0xb3 : \
(nr) == 1 ? 0x220 : 0x218) + (index))
/* bit field, fan1 is bit0, fan2 is bit1 ... */
#define W83793_REG_TEMP_FAN_MAP(index) (0x201 + (index))
#define W83793_REG_TEMP_TOL(index) (0x208 + (index))
#define W83793_REG_TEMP_CRUISE(index) (0x210 + (index))
#define W83793_REG_PWM_STOP_TIME(index) (0x228 + (index))
#define W83793_REG_SF2_TEMP(index, nr) (0x230 + ((index) << 4) + (nr))
#define W83793_REG_SF2_PWM(index, nr) (0x238 + ((index) << 4) + (nr))
static inline unsigned long FAN_FROM_REG(u16 val)
{
if ((val >= 0xfff) || (val == 0))
return 0;
return 1350000UL / val;
}
static inline u16 FAN_TO_REG(long rpm)
{
if (rpm <= 0)
return 0x0fff;
return clamp_val((1350000 + (rpm >> 1)) / rpm, 1, 0xffe);
}
static inline unsigned long TIME_FROM_REG(u8 reg)
{
return reg * 100;
}
static inline u8 TIME_TO_REG(unsigned long val)
{
return clamp_val((val + 50) / 100, 0, 0xff);
}
static inline long TEMP_FROM_REG(s8 reg)
{
return reg * 1000;
}
static inline s8 TEMP_TO_REG(long val, s8 min, s8 max)
{
return clamp_val((val + (val < 0 ? -500 : 500)) / 1000, min, max);
}
struct w83793_data {
struct i2c_client *lm75[2];
struct device *hwmon_dev;
struct mutex update_lock;
char valid; /* !=0 if following fields are valid */
unsigned long last_updated; /* In jiffies */
unsigned long last_nonvolatile; /* In jiffies, last time we update the
* nonvolatile registers
*/
u8 bank;
u8 vrm;
u8 vid[2];
u8 in[10][3]; /* Register value, read/high/low */
u8 in_low_bits[3]; /* Additional resolution for VCore A/B Vtt */
u16 has_fan; /* Only fan1- fan5 has own pins */
u16 fan[12]; /* Register value combine */
u16 fan_min[12]; /* Register value combine */
s8 temp[6][5]; /* current, crit, crit_hyst,warn, warn_hyst */
u8 temp_low_bits; /* Additional resolution TD1-TD4 */
u8 temp_mode[2]; /* byte 0: Temp D1-D4 mode each has 2 bits
* byte 1: Temp R1,R2 mode, each has 1 bit
*/
u8 temp_critical; /* If reached all fan will be at full speed */
u8 temp_fan_map[6]; /* Temp controls which pwm fan, bit field */
u8 has_pwm;
u8 has_temp;
u8 has_vid;
u8 pwm_enable; /* Register value, each Temp has 1 bit */
u8 pwm_uptime; /* Register value */
u8 pwm_downtime; /* Register value */
u8 pwm_default; /* All fan default pwm, next poweron valid */
u8 pwm[8][3]; /* Register value */
u8 pwm_stop_time[8];
u8 temp_cruise[6];
u8 alarms[5]; /* realtime status registers */
u8 beeps[5];
u8 beep_enable;
u8 tolerance[3]; /* Temp tolerance(Smart Fan I/II) */
u8 sf2_pwm[6][7]; /* Smart FanII: Fan duty cycle */
u8 sf2_temp[6][7]; /* Smart FanII: Temp level point */
/* watchdog */
struct i2c_client *client;
struct mutex watchdog_lock;
struct list_head list; /* member of the watchdog_data_list */
struct kref kref;
struct miscdevice watchdog_miscdev;
unsigned long watchdog_is_open;
char watchdog_expect_close;
char watchdog_name[10]; /* must be unique to avoid sysfs conflict */
unsigned int watchdog_caused_reboot;
int watchdog_timeout; /* watchdog timeout in minutes */
};
/*
* Somewhat ugly :( global data pointer list with all devices, so that
* we can find our device data as when using misc_register. There is no
* other method to get to one's device data from the open file-op and
* for usage in the reboot notifier callback.
*/
static LIST_HEAD(watchdog_data_list);
/* Note this lock not only protect list access, but also data.kref access */
static DEFINE_MUTEX(watchdog_data_mutex);
/*
* Release our data struct when we're detached from the i2c client *and* all
* references to our watchdog device are released
*/
static void w83793_release_resources(struct kref *ref)
{
struct w83793_data *data = container_of(ref, struct w83793_data, kref);
kfree(data);
}
static u8 w83793_read_value(struct i2c_client *client, u16 reg);
static int w83793_write_value(struct i2c_client *client, u16 reg, u8 value);
static int w83793_probe(struct i2c_client *client,
const struct i2c_device_id *id);
static int w83793_detect(struct i2c_client *client,
struct i2c_board_info *info);
static int w83793_remove(struct i2c_client *client);
static void w83793_init_client(struct i2c_client *client);
static void w83793_update_nonvolatile(struct device *dev);
static struct w83793_data *w83793_update_device(struct device *dev);
static const struct i2c_device_id w83793_id[] = {
{ "w83793", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, w83793_id);
static struct i2c_driver w83793_driver = {
.class = I2C_CLASS_HWMON,
.driver = {
.name = "w83793",
},
.probe = w83793_probe,
.remove = w83793_remove,
.id_table = w83793_id,
.detect = w83793_detect,
.address_list = normal_i2c,
};
static ssize_t
show_vrm(struct device *dev, struct device_attribute *attr, char *buf)
{
struct w83793_data *data = dev_get_drvdata(dev);
return sprintf(buf, "%d\n", data->vrm);
}
static ssize_t
show_vid(struct device *dev, struct device_attribute *attr, char *buf)
{
struct w83793_data *data = w83793_update_device(dev);
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int index = sensor_attr->index;
return sprintf(buf, "%d\n", vid_from_reg(data->vid[index], data->vrm));
}
static ssize_t
store_vrm(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct w83793_data *data = dev_get_drvdata(dev);
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
if (val > 255)
return -EINVAL;
data->vrm = val;
return count;
}
#define ALARM_STATUS 0
#define BEEP_ENABLE 1
static ssize_t
show_alarm_beep(struct device *dev, struct device_attribute *attr, char *buf)
{
struct w83793_data *data = w83793_update_device(dev);
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index >> 3;
int bit = sensor_attr->index & 0x07;
u8 val;
if (nr == ALARM_STATUS) {
val = (data->alarms[index] >> (bit)) & 1;
} else { /* BEEP_ENABLE */
val = (data->beeps[index] >> (bit)) & 1;
}
return sprintf(buf, "%u\n", val);
}
static ssize_t
store_beep(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int index = sensor_attr->index >> 3;
int shift = sensor_attr->index & 0x07;
u8 beep_bit = 1 << shift;
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
if (val > 1)
return -EINVAL;
mutex_lock(&data->update_lock);
data->beeps[index] = w83793_read_value(client, W83793_REG_BEEP(index));
data->beeps[index] &= ~beep_bit;
data->beeps[index] |= val << shift;
w83793_write_value(client, W83793_REG_BEEP(index), data->beeps[index]);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t
show_beep_enable(struct device *dev, struct device_attribute *attr, char *buf)
{
struct w83793_data *data = w83793_update_device(dev);
return sprintf(buf, "%u\n", (data->beep_enable >> 1) & 0x01);
}
static ssize_t
store_beep_enable(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
if (val > 1)
return -EINVAL;
mutex_lock(&data->update_lock);
data->beep_enable = w83793_read_value(client, W83793_REG_OVT_BEEP)
& 0xfd;
data->beep_enable |= val << 1;
w83793_write_value(client, W83793_REG_OVT_BEEP, data->beep_enable);
mutex_unlock(&data->update_lock);
return count;
}
/* Write 0 to clear chassis alarm */
static ssize_t
store_chassis_clear(struct device *dev,
struct device_attribute *attr, const char *buf,
size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
unsigned long val;
u8 reg;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
if (val)
return -EINVAL;
mutex_lock(&data->update_lock);
reg = w83793_read_value(client, W83793_REG_CLR_CHASSIS);
w83793_write_value(client, W83793_REG_CLR_CHASSIS, reg | 0x80);
data->valid = 0; /* Force cache refresh */
mutex_unlock(&data->update_lock);
return count;
}
#define FAN_INPUT 0
#define FAN_MIN 1
static ssize_t
show_fan(struct device *dev, struct device_attribute *attr, char *buf)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
struct w83793_data *data = w83793_update_device(dev);
u16 val;
if (nr == FAN_INPUT)
val = data->fan[index] & 0x0fff;
else
val = data->fan_min[index] & 0x0fff;
return sprintf(buf, "%lu\n", FAN_FROM_REG(val));
}
static ssize_t
store_fan_min(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int index = sensor_attr->index;
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
val = FAN_TO_REG(val);
mutex_lock(&data->update_lock);
data->fan_min[index] = val;
w83793_write_value(client, W83793_REG_FAN_MIN(index),
(val >> 8) & 0xff);
w83793_write_value(client, W83793_REG_FAN_MIN(index) + 1, val & 0xff);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t
show_pwm(struct device *dev, struct device_attribute *attr, char *buf)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
struct w83793_data *data = w83793_update_device(dev);
u16 val;
int nr = sensor_attr->nr;
int index = sensor_attr->index;
if (nr == PWM_STOP_TIME)
val = TIME_FROM_REG(data->pwm_stop_time[index]);
else
val = (data->pwm[index][nr] & 0x3f) << 2;
return sprintf(buf, "%d\n", val);
}
static ssize_t
store_pwm(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
mutex_lock(&data->update_lock);
if (nr == PWM_STOP_TIME) {
val = TIME_TO_REG(val);
data->pwm_stop_time[index] = val;
w83793_write_value(client, W83793_REG_PWM_STOP_TIME(index),
val);
} else {
val = clamp_val(val, 0, 0xff) >> 2;
data->pwm[index][nr] =
w83793_read_value(client, W83793_REG_PWM(index, nr)) & 0xc0;
data->pwm[index][nr] |= val;
w83793_write_value(client, W83793_REG_PWM(index, nr),
data->pwm[index][nr]);
}
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t
show_temp(struct device *dev, struct device_attribute *attr, char *buf)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
struct w83793_data *data = w83793_update_device(dev);
long temp = TEMP_FROM_REG(data->temp[index][nr]);
if (nr == TEMP_READ && index < 4) { /* Only TD1-TD4 have low bits */
int low = ((data->temp_low_bits >> (index * 2)) & 0x03) * 250;
temp += temp > 0 ? low : -low;
}
return sprintf(buf, "%ld\n", temp);
}
static ssize_t
store_temp(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
long tmp;
int err;
err = kstrtol(buf, 10, &tmp);
if (err)
return err;
mutex_lock(&data->update_lock);
data->temp[index][nr] = TEMP_TO_REG(tmp, -128, 127);
w83793_write_value(client, W83793_REG_TEMP[index][nr],
data->temp[index][nr]);
mutex_unlock(&data->update_lock);
return count;
}
/*
* TD1-TD4
* each has 4 mode:(2 bits)
* 0: Stop monitor
* 1: Use internal temp sensor(default)
* 2: Reserved
* 3: Use sensor in Intel CPU and get result by PECI
*
* TR1-TR2
* each has 2 mode:(1 bit)
* 0: Disable temp sensor monitor
* 1: To enable temp sensors monitor
*/
/* 0 disable, 6 PECI */
static u8 TO_TEMP_MODE[] = { 0, 0, 0, 6 };
static ssize_t
show_temp_mode(struct device *dev, struct device_attribute *attr, char *buf)
{
struct w83793_data *data = w83793_update_device(dev);
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int index = sensor_attr->index;
u8 mask = (index < 4) ? 0x03 : 0x01;
u8 shift = (index < 4) ? (2 * index) : (index - 4);
u8 tmp;
index = (index < 4) ? 0 : 1;
tmp = (data->temp_mode[index] >> shift) & mask;
/* for the internal sensor, found out if diode or thermistor */
if (tmp == 1)
tmp = index == 0 ? 3 : 4;
else
tmp = TO_TEMP_MODE[tmp];
return sprintf(buf, "%d\n", tmp);
}
static ssize_t
store_temp_mode(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int index = sensor_attr->index;
u8 mask = (index < 4) ? 0x03 : 0x01;
u8 shift = (index < 4) ? (2 * index) : (index - 4);
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
/* transform the sysfs interface values into table above */
if ((val == 6) && (index < 4)) {
val -= 3;
} else if ((val == 3 && index < 4)
|| (val == 4 && index >= 4)) {
/* transform diode or thermistor into internal enable */
val = !!val;
} else {
return -EINVAL;
}
index = (index < 4) ? 0 : 1;
mutex_lock(&data->update_lock);
data->temp_mode[index] =
w83793_read_value(client, W83793_REG_TEMP_MODE[index]);
data->temp_mode[index] &= ~(mask << shift);
data->temp_mode[index] |= val << shift;
w83793_write_value(client, W83793_REG_TEMP_MODE[index],
data->temp_mode[index]);
mutex_unlock(&data->update_lock);
return count;
}
#define SETUP_PWM_DEFAULT 0
#define SETUP_PWM_UPTIME 1 /* Unit in 0.1s */
#define SETUP_PWM_DOWNTIME 2 /* Unit in 0.1s */
#define SETUP_TEMP_CRITICAL 3
static ssize_t
show_sf_setup(struct device *dev, struct device_attribute *attr, char *buf)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
struct w83793_data *data = w83793_update_device(dev);
u32 val = 0;
if (nr == SETUP_PWM_DEFAULT)
val = (data->pwm_default & 0x3f) << 2;
else if (nr == SETUP_PWM_UPTIME)
val = TIME_FROM_REG(data->pwm_uptime);
else if (nr == SETUP_PWM_DOWNTIME)
val = TIME_FROM_REG(data->pwm_downtime);
else if (nr == SETUP_TEMP_CRITICAL)
val = TEMP_FROM_REG(data->temp_critical & 0x7f);
return sprintf(buf, "%d\n", val);
}
static ssize_t
store_sf_setup(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
long val;
int err;
err = kstrtol(buf, 10, &val);
if (err)
return err;
mutex_lock(&data->update_lock);
if (nr == SETUP_PWM_DEFAULT) {
data->pwm_default =
w83793_read_value(client, W83793_REG_PWM_DEFAULT) & 0xc0;
data->pwm_default |= clamp_val(val, 0, 0xff) >> 2;
w83793_write_value(client, W83793_REG_PWM_DEFAULT,
data->pwm_default);
} else if (nr == SETUP_PWM_UPTIME) {
data->pwm_uptime = TIME_TO_REG(val);
data->pwm_uptime += data->pwm_uptime == 0 ? 1 : 0;
w83793_write_value(client, W83793_REG_PWM_UPTIME,
data->pwm_uptime);
} else if (nr == SETUP_PWM_DOWNTIME) {
data->pwm_downtime = TIME_TO_REG(val);
data->pwm_downtime += data->pwm_downtime == 0 ? 1 : 0;
w83793_write_value(client, W83793_REG_PWM_DOWNTIME,
data->pwm_downtime);
} else { /* SETUP_TEMP_CRITICAL */
data->temp_critical =
w83793_read_value(client, W83793_REG_TEMP_CRITICAL) & 0x80;
data->temp_critical |= TEMP_TO_REG(val, 0, 0x7f);
w83793_write_value(client, W83793_REG_TEMP_CRITICAL,
data->temp_critical);
}
mutex_unlock(&data->update_lock);
return count;
}
/*
* Temp SmartFan control
* TEMP_FAN_MAP
* Temp channel control which pwm fan, bitfield, bit 0 indicate pwm1...
* It's possible two or more temp channels control the same fan, w83793
* always prefers to pick the most critical request and applies it to
* the related Fan.
* It's possible one fan is not in any mapping of 6 temp channels, this
* means the fan is manual mode
*
* TEMP_PWM_ENABLE
* Each temp channel has its own SmartFan mode, and temp channel
* control fans that are set by TEMP_FAN_MAP
* 0: SmartFanII mode
* 1: Thermal Cruise Mode
*
* TEMP_CRUISE
* Target temperature in thermal cruise mode, w83793 will try to turn
* fan speed to keep the temperature of target device around this
* temperature.
*
* TEMP_TOLERANCE
* If Temp higher or lower than target with this tolerance, w83793
* will take actions to speed up or slow down the fan to keep the
* temperature within the tolerance range.
*/
#define TEMP_FAN_MAP 0
#define TEMP_PWM_ENABLE 1
#define TEMP_CRUISE 2
#define TEMP_TOLERANCE 3
static ssize_t
show_sf_ctrl(struct device *dev, struct device_attribute *attr, char *buf)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
struct w83793_data *data = w83793_update_device(dev);
u32 val;
if (nr == TEMP_FAN_MAP) {
val = data->temp_fan_map[index];
} else if (nr == TEMP_PWM_ENABLE) {
/* +2 to transform into 2 and 3 to conform with sysfs intf */
val = ((data->pwm_enable >> index) & 0x01) + 2;
} else if (nr == TEMP_CRUISE) {
val = TEMP_FROM_REG(data->temp_cruise[index] & 0x7f);
} else { /* TEMP_TOLERANCE */
val = data->tolerance[index >> 1] >> ((index & 0x01) ? 4 : 0);
val = TEMP_FROM_REG(val & 0x0f);
}
return sprintf(buf, "%d\n", val);
}
static ssize_t
store_sf_ctrl(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
long val;
int err;
err = kstrtol(buf, 10, &val);
if (err)
return err;
mutex_lock(&data->update_lock);
if (nr == TEMP_FAN_MAP) {
val = clamp_val(val, 0, 255);
w83793_write_value(client, W83793_REG_TEMP_FAN_MAP(index), val);
data->temp_fan_map[index] = val;
} else if (nr == TEMP_PWM_ENABLE) {
if (val == 2 || val == 3) {
data->pwm_enable =
w83793_read_value(client, W83793_REG_PWM_ENABLE);
if (val - 2)
data->pwm_enable |= 1 << index;
else
data->pwm_enable &= ~(1 << index);
w83793_write_value(client, W83793_REG_PWM_ENABLE,
data->pwm_enable);
} else {
mutex_unlock(&data->update_lock);
return -EINVAL;
}
} else if (nr == TEMP_CRUISE) {
data->temp_cruise[index] =
w83793_read_value(client, W83793_REG_TEMP_CRUISE(index));
data->temp_cruise[index] &= 0x80;
data->temp_cruise[index] |= TEMP_TO_REG(val, 0, 0x7f);
w83793_write_value(client, W83793_REG_TEMP_CRUISE(index),
data->temp_cruise[index]);
} else { /* TEMP_TOLERANCE */
int i = index >> 1;
u8 shift = (index & 0x01) ? 4 : 0;
data->tolerance[i] =
w83793_read_value(client, W83793_REG_TEMP_TOL(i));
data->tolerance[i] &= ~(0x0f << shift);
data->tolerance[i] |= TEMP_TO_REG(val, 0, 0x0f) << shift;
w83793_write_value(client, W83793_REG_TEMP_TOL(i),
data->tolerance[i]);
}
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t
show_sf2_pwm(struct device *dev, struct device_attribute *attr, char *buf)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
struct w83793_data *data = w83793_update_device(dev);
return sprintf(buf, "%d\n", (data->sf2_pwm[index][nr] & 0x3f) << 2);
}
static ssize_t
store_sf2_pwm(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
val = clamp_val(val, 0, 0xff) >> 2;
mutex_lock(&data->update_lock);
data->sf2_pwm[index][nr] =
w83793_read_value(client, W83793_REG_SF2_PWM(index, nr)) & 0xc0;
data->sf2_pwm[index][nr] |= val;
w83793_write_value(client, W83793_REG_SF2_PWM(index, nr),
data->sf2_pwm[index][nr]);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t
show_sf2_temp(struct device *dev, struct device_attribute *attr, char *buf)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
struct w83793_data *data = w83793_update_device(dev);
return sprintf(buf, "%ld\n",
TEMP_FROM_REG(data->sf2_temp[index][nr] & 0x7f));
}
static ssize_t
store_sf2_temp(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
long val;
int err;
err = kstrtol(buf, 10, &val);
if (err)
return err;
val = TEMP_TO_REG(val, 0, 0x7f);
mutex_lock(&data->update_lock);
data->sf2_temp[index][nr] =
w83793_read_value(client, W83793_REG_SF2_TEMP(index, nr)) & 0x80;
data->sf2_temp[index][nr] |= val;
w83793_write_value(client, W83793_REG_SF2_TEMP(index, nr),
data->sf2_temp[index][nr]);
mutex_unlock(&data->update_lock);
return count;
}
/* only Vcore A/B and Vtt have additional 2 bits precision */
static ssize_t
show_in(struct device *dev, struct device_attribute *attr, char *buf)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
struct w83793_data *data = w83793_update_device(dev);
u16 val = data->in[index][nr];
if (index < 3) {
val <<= 2;
val += (data->in_low_bits[nr] >> (index * 2)) & 0x3;
}
/* voltage inputs 5VDD and 5VSB needs 150mV offset */
val = val * scale_in[index] + scale_in_add[index];
return sprintf(buf, "%d\n", val);
}
static ssize_t
store_in(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct sensor_device_attribute_2 *sensor_attr =
to_sensor_dev_attr_2(attr);
int nr = sensor_attr->nr;
int index = sensor_attr->index;
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
val = (val + scale_in[index] / 2) / scale_in[index];
mutex_lock(&data->update_lock);
if (index > 2) {
/* fix the limit values of 5VDD and 5VSB to ALARM mechanism */
if (nr == 1 || nr == 2)
val -= scale_in_add[index] / scale_in[index];
val = clamp_val(val, 0, 255);
} else {
val = clamp_val(val, 0, 0x3FF);
data->in_low_bits[nr] =
w83793_read_value(client, W83793_REG_IN_LOW_BITS[nr]);
data->in_low_bits[nr] &= ~(0x03 << (2 * index));
data->in_low_bits[nr] |= (val & 0x03) << (2 * index);
w83793_write_value(client, W83793_REG_IN_LOW_BITS[nr],
data->in_low_bits[nr]);
val >>= 2;
}
data->in[index][nr] = val;
w83793_write_value(client, W83793_REG_IN[index][nr],
data->in[index][nr]);
mutex_unlock(&data->update_lock);
return count;
}
#define NOT_USED -1
#define SENSOR_ATTR_IN(index) \
SENSOR_ATTR_2(in##index##_input, S_IRUGO, show_in, NULL, \
IN_READ, index), \
SENSOR_ATTR_2(in##index##_max, S_IRUGO | S_IWUSR, show_in, \
store_in, IN_MAX, index), \
SENSOR_ATTR_2(in##index##_min, S_IRUGO | S_IWUSR, show_in, \
store_in, IN_LOW, index), \
SENSOR_ATTR_2(in##index##_alarm, S_IRUGO, show_alarm_beep, \
NULL, ALARM_STATUS, index + ((index > 2) ? 1 : 0)), \
SENSOR_ATTR_2(in##index##_beep, S_IWUSR | S_IRUGO, \
show_alarm_beep, store_beep, BEEP_ENABLE, \
index + ((index > 2) ? 1 : 0))
#define SENSOR_ATTR_FAN(index) \
SENSOR_ATTR_2(fan##index##_alarm, S_IRUGO, show_alarm_beep, \
NULL, ALARM_STATUS, index + 17), \
SENSOR_ATTR_2(fan##index##_beep, S_IWUSR | S_IRUGO, \
show_alarm_beep, store_beep, BEEP_ENABLE, index + 17), \
SENSOR_ATTR_2(fan##index##_input, S_IRUGO, show_fan, \
NULL, FAN_INPUT, index - 1), \
SENSOR_ATTR_2(fan##index##_min, S_IWUSR | S_IRUGO, \
show_fan, store_fan_min, FAN_MIN, index - 1)
#define SENSOR_ATTR_PWM(index) \
SENSOR_ATTR_2(pwm##index, S_IWUSR | S_IRUGO, show_pwm, \
store_pwm, PWM_DUTY, index - 1), \
SENSOR_ATTR_2(pwm##index##_nonstop, S_IWUSR | S_IRUGO, \
show_pwm, store_pwm, PWM_NONSTOP, index - 1), \
SENSOR_ATTR_2(pwm##index##_start, S_IWUSR | S_IRUGO, \
show_pwm, store_pwm, PWM_START, index - 1), \
SENSOR_ATTR_2(pwm##index##_stop_time, S_IWUSR | S_IRUGO, \
show_pwm, store_pwm, PWM_STOP_TIME, index - 1)
#define SENSOR_ATTR_TEMP(index) \
SENSOR_ATTR_2(temp##index##_type, S_IRUGO | S_IWUSR, \
show_temp_mode, store_temp_mode, NOT_USED, index - 1), \
SENSOR_ATTR_2(temp##index##_input, S_IRUGO, show_temp, \
NULL, TEMP_READ, index - 1), \
SENSOR_ATTR_2(temp##index##_max, S_IRUGO | S_IWUSR, show_temp, \
store_temp, TEMP_CRIT, index - 1), \
SENSOR_ATTR_2(temp##index##_max_hyst, S_IRUGO | S_IWUSR, \
show_temp, store_temp, TEMP_CRIT_HYST, index - 1), \
SENSOR_ATTR_2(temp##index##_warn, S_IRUGO | S_IWUSR, show_temp, \
store_temp, TEMP_WARN, index - 1), \
SENSOR_ATTR_2(temp##index##_warn_hyst, S_IRUGO | S_IWUSR, \
show_temp, store_temp, TEMP_WARN_HYST, index - 1), \
SENSOR_ATTR_2(temp##index##_alarm, S_IRUGO, \
show_alarm_beep, NULL, ALARM_STATUS, index + 11), \
SENSOR_ATTR_2(temp##index##_beep, S_IWUSR | S_IRUGO, \
show_alarm_beep, store_beep, BEEP_ENABLE, index + 11), \
SENSOR_ATTR_2(temp##index##_auto_channels_pwm, \
S_IRUGO | S_IWUSR, show_sf_ctrl, store_sf_ctrl, \
TEMP_FAN_MAP, index - 1), \
SENSOR_ATTR_2(temp##index##_pwm_enable, S_IWUSR | S_IRUGO, \
show_sf_ctrl, store_sf_ctrl, TEMP_PWM_ENABLE, \
index - 1), \
SENSOR_ATTR_2(thermal_cruise##index, S_IRUGO | S_IWUSR, \
show_sf_ctrl, store_sf_ctrl, TEMP_CRUISE, index - 1), \
SENSOR_ATTR_2(tolerance##index, S_IRUGO | S_IWUSR, show_sf_ctrl,\
store_sf_ctrl, TEMP_TOLERANCE, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point1_pwm, S_IRUGO | S_IWUSR, \
show_sf2_pwm, store_sf2_pwm, 0, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point2_pwm, S_IRUGO | S_IWUSR, \
show_sf2_pwm, store_sf2_pwm, 1, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point3_pwm, S_IRUGO | S_IWUSR, \
show_sf2_pwm, store_sf2_pwm, 2, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point4_pwm, S_IRUGO | S_IWUSR, \
show_sf2_pwm, store_sf2_pwm, 3, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point5_pwm, S_IRUGO | S_IWUSR, \
show_sf2_pwm, store_sf2_pwm, 4, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point6_pwm, S_IRUGO | S_IWUSR, \
show_sf2_pwm, store_sf2_pwm, 5, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point7_pwm, S_IRUGO | S_IWUSR, \
show_sf2_pwm, store_sf2_pwm, 6, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point1_temp, S_IRUGO | S_IWUSR,\
show_sf2_temp, store_sf2_temp, 0, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point2_temp, S_IRUGO | S_IWUSR,\
show_sf2_temp, store_sf2_temp, 1, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point3_temp, S_IRUGO | S_IWUSR,\
show_sf2_temp, store_sf2_temp, 2, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point4_temp, S_IRUGO | S_IWUSR,\
show_sf2_temp, store_sf2_temp, 3, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point5_temp, S_IRUGO | S_IWUSR,\
show_sf2_temp, store_sf2_temp, 4, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point6_temp, S_IRUGO | S_IWUSR,\
show_sf2_temp, store_sf2_temp, 5, index - 1), \
SENSOR_ATTR_2(temp##index##_auto_point7_temp, S_IRUGO | S_IWUSR,\
show_sf2_temp, store_sf2_temp, 6, index - 1)
static struct sensor_device_attribute_2 w83793_sensor_attr_2[] = {
SENSOR_ATTR_IN(0),
SENSOR_ATTR_IN(1),
SENSOR_ATTR_IN(2),
SENSOR_ATTR_IN(3),
SENSOR_ATTR_IN(4),
SENSOR_ATTR_IN(5),
SENSOR_ATTR_IN(6),
SENSOR_ATTR_IN(7),
SENSOR_ATTR_IN(8),
SENSOR_ATTR_IN(9),
SENSOR_ATTR_FAN(1),
SENSOR_ATTR_FAN(2),
SENSOR_ATTR_FAN(3),
SENSOR_ATTR_FAN(4),
SENSOR_ATTR_FAN(5),
SENSOR_ATTR_PWM(1),
SENSOR_ATTR_PWM(2),
SENSOR_ATTR_PWM(3),
};
static struct sensor_device_attribute_2 w83793_temp[] = {
SENSOR_ATTR_TEMP(1),
SENSOR_ATTR_TEMP(2),
SENSOR_ATTR_TEMP(3),
SENSOR_ATTR_TEMP(4),
SENSOR_ATTR_TEMP(5),
SENSOR_ATTR_TEMP(6),
};
/* Fan6-Fan12 */
static struct sensor_device_attribute_2 w83793_left_fan[] = {
SENSOR_ATTR_FAN(6),
SENSOR_ATTR_FAN(7),
SENSOR_ATTR_FAN(8),
SENSOR_ATTR_FAN(9),
SENSOR_ATTR_FAN(10),
SENSOR_ATTR_FAN(11),
SENSOR_ATTR_FAN(12),
};
/* Pwm4-Pwm8 */
static struct sensor_device_attribute_2 w83793_left_pwm[] = {
SENSOR_ATTR_PWM(4),
SENSOR_ATTR_PWM(5),
SENSOR_ATTR_PWM(6),
SENSOR_ATTR_PWM(7),
SENSOR_ATTR_PWM(8),
};
static struct sensor_device_attribute_2 w83793_vid[] = {
SENSOR_ATTR_2(cpu0_vid, S_IRUGO, show_vid, NULL, NOT_USED, 0),
SENSOR_ATTR_2(cpu1_vid, S_IRUGO, show_vid, NULL, NOT_USED, 1),
};
static DEVICE_ATTR(vrm, S_IWUSR | S_IRUGO, show_vrm, store_vrm);
static struct sensor_device_attribute_2 sda_single_files[] = {
SENSOR_ATTR_2(intrusion0_alarm, S_IWUSR | S_IRUGO, show_alarm_beep,
store_chassis_clear, ALARM_STATUS, 30),
SENSOR_ATTR_2(beep_enable, S_IWUSR | S_IRUGO, show_beep_enable,
store_beep_enable, NOT_USED, NOT_USED),
SENSOR_ATTR_2(pwm_default, S_IWUSR | S_IRUGO, show_sf_setup,
store_sf_setup, SETUP_PWM_DEFAULT, NOT_USED),
SENSOR_ATTR_2(pwm_uptime, S_IWUSR | S_IRUGO, show_sf_setup,
store_sf_setup, SETUP_PWM_UPTIME, NOT_USED),
SENSOR_ATTR_2(pwm_downtime, S_IWUSR | S_IRUGO, show_sf_setup,
store_sf_setup, SETUP_PWM_DOWNTIME, NOT_USED),
SENSOR_ATTR_2(temp_critical, S_IWUSR | S_IRUGO, show_sf_setup,
store_sf_setup, SETUP_TEMP_CRITICAL, NOT_USED),
};
static void w83793_init_client(struct i2c_client *client)
{
if (reset)
w83793_write_value(client, W83793_REG_CONFIG, 0x80);
/* Start monitoring */
w83793_write_value(client, W83793_REG_CONFIG,
w83793_read_value(client, W83793_REG_CONFIG) | 0x01);
}
/*
* Watchdog routines
*/
static int watchdog_set_timeout(struct w83793_data *data, int timeout)
{
unsigned int mtimeout;
int ret;
mtimeout = DIV_ROUND_UP(timeout, 60);
if (mtimeout > 255)
return -EINVAL;
mutex_lock(&data->watchdog_lock);
if (!data->client) {
ret = -ENODEV;
goto leave;
}
data->watchdog_timeout = mtimeout;
/* Set Timeout value (in Minutes) */
w83793_write_value(data->client, W83793_REG_WDT_TIMEOUT,
data->watchdog_timeout);
ret = mtimeout * 60;
leave:
mutex_unlock(&data->watchdog_lock);
return ret;
}
static int watchdog_get_timeout(struct w83793_data *data)
{
int timeout;
mutex_lock(&data->watchdog_lock);
timeout = data->watchdog_timeout * 60;
mutex_unlock(&data->watchdog_lock);
return timeout;
}
static int watchdog_trigger(struct w83793_data *data)
{
int ret = 0;
mutex_lock(&data->watchdog_lock);
if (!data->client) {
ret = -ENODEV;
goto leave;
}
/* Set Timeout value (in Minutes) */
w83793_write_value(data->client, W83793_REG_WDT_TIMEOUT,
data->watchdog_timeout);
leave:
mutex_unlock(&data->watchdog_lock);
return ret;
}
static int watchdog_enable(struct w83793_data *data)
{
int ret = 0;
mutex_lock(&data->watchdog_lock);
if (!data->client) {
ret = -ENODEV;
goto leave;
}
/* Set initial timeout */
w83793_write_value(data->client, W83793_REG_WDT_TIMEOUT,
data->watchdog_timeout);
/* Enable Soft Watchdog */
w83793_write_value(data->client, W83793_REG_WDT_LOCK, 0x55);
leave:
mutex_unlock(&data->watchdog_lock);
return ret;
}
static int watchdog_disable(struct w83793_data *data)
{
int ret = 0;
mutex_lock(&data->watchdog_lock);
if (!data->client) {
ret = -ENODEV;
goto leave;
}
/* Disable Soft Watchdog */
w83793_write_value(data->client, W83793_REG_WDT_LOCK, 0xAA);
leave:
mutex_unlock(&data->watchdog_lock);
return ret;
}
static int watchdog_open(struct inode *inode, struct file *filp)
{
struct w83793_data *pos, *data = NULL;
int watchdog_is_open;
/*
* We get called from drivers/char/misc.c with misc_mtx hold, and we
* call misc_register() from w83793_probe() with watchdog_data_mutex
* hold, as misc_register() takes the misc_mtx lock, this is a possible
* deadlock, so we use mutex_trylock here.
*/
if (!mutex_trylock(&watchdog_data_mutex))
return -ERESTARTSYS;
list_for_each_entry(pos, &watchdog_data_list, list) {
if (pos->watchdog_miscdev.minor == iminor(inode)) {
data = pos;
break;
}
}
/* Check, if device is already open */
watchdog_is_open = test_and_set_bit(0, &data->watchdog_is_open);
/*
* Increase data reference counter (if not already done).
* Note we can never not have found data, so we don't check for this
*/
if (!watchdog_is_open)
kref_get(&data->kref);
mutex_unlock(&watchdog_data_mutex);
/* Check, if device is already open and possibly issue error */
if (watchdog_is_open)
return -EBUSY;
/* Enable Soft Watchdog */
watchdog_enable(data);
/* Store pointer to data into filp's private data */
filp->private_data = data;
return nonseekable_open(inode, filp);
}
static int watchdog_close(struct inode *inode, struct file *filp)
{
struct w83793_data *data = filp->private_data;
if (data->watchdog_expect_close) {
watchdog_disable(data);
data->watchdog_expect_close = 0;
} else {
watchdog_trigger(data);
dev_crit(&data->client->dev,
"unexpected close, not stopping watchdog!\n");
}
clear_bit(0, &data->watchdog_is_open);
/* Decrease data reference counter */
mutex_lock(&watchdog_data_mutex);
kref_put(&data->kref, w83793_release_resources);
mutex_unlock(&watchdog_data_mutex);
return 0;
}
static ssize_t watchdog_write(struct file *filp, const char __user *buf,
size_t count, loff_t *offset)
{
ssize_t ret;
struct w83793_data *data = filp->private_data;
if (count) {
if (!nowayout) {
size_t i;
/* Clear it in case it was set with a previous write */
data->watchdog_expect_close = 0;
for (i = 0; i != count; i++) {
char c;
if (get_user(c, buf + i))
return -EFAULT;
if (c == 'V')
data->watchdog_expect_close = 1;
}
}
ret = watchdog_trigger(data);
if (ret < 0)
return ret;
}
return count;
}
static long watchdog_ioctl(struct file *filp, unsigned int cmd,
unsigned long arg)
{
struct watchdog_info ident = {
.options = WDIOF_KEEPALIVEPING |
WDIOF_SETTIMEOUT |
WDIOF_CARDRESET,
.identity = "w83793 watchdog"
};
int val, ret = 0;
struct w83793_data *data = filp->private_data;
switch (cmd) {
case WDIOC_GETSUPPORT:
if (!nowayout)
ident.options |= WDIOF_MAGICCLOSE;
if (copy_to_user((void __user *)arg, &ident, sizeof(ident)))
ret = -EFAULT;
break;
case WDIOC_GETSTATUS:
val = data->watchdog_caused_reboot ? WDIOF_CARDRESET : 0;
ret = put_user(val, (int __user *)arg);
break;
case WDIOC_GETBOOTSTATUS:
ret = put_user(0, (int __user *)arg);
break;
case WDIOC_KEEPALIVE:
ret = watchdog_trigger(data);
break;
case WDIOC_GETTIMEOUT:
val = watchdog_get_timeout(data);
ret = put_user(val, (int __user *)arg);
break;
case WDIOC_SETTIMEOUT:
if (get_user(val, (int __user *)arg)) {
ret = -EFAULT;
break;
}
ret = watchdog_set_timeout(data, val);
if (ret > 0)
ret = put_user(ret, (int __user *)arg);
break;
case WDIOC_SETOPTIONS:
if (get_user(val, (int __user *)arg)) {
ret = -EFAULT;
break;
}
if (val & WDIOS_DISABLECARD)
ret = watchdog_disable(data);
else if (val & WDIOS_ENABLECARD)
ret = watchdog_enable(data);
else
ret = -EINVAL;
break;
default:
ret = -ENOTTY;
}
return ret;
}
static const struct file_operations watchdog_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
.open = watchdog_open,
.release = watchdog_close,
.write = watchdog_write,
.unlocked_ioctl = watchdog_ioctl,
};
/*
* Notifier for system down
*/
static int watchdog_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
struct w83793_data *data = NULL;
if (code == SYS_DOWN || code == SYS_HALT) {
/* Disable each registered watchdog */
mutex_lock(&watchdog_data_mutex);
list_for_each_entry(data, &watchdog_data_list, list) {
if (data->watchdog_miscdev.minor)
watchdog_disable(data);
}
mutex_unlock(&watchdog_data_mutex);
}
return NOTIFY_DONE;
}
/*
* The WDT needs to learn about soft shutdowns in order to
* turn the timebomb registers off.
*/
static struct notifier_block watchdog_notifier = {
.notifier_call = watchdog_notify_sys,
};
/*
* Init / remove routines
*/
static int w83793_remove(struct i2c_client *client)
{
struct w83793_data *data = i2c_get_clientdata(client);
struct device *dev = &client->dev;
int i, tmp;
/* Unregister the watchdog (if registered) */
if (data->watchdog_miscdev.minor) {
misc_deregister(&data->watchdog_miscdev);
if (data->watchdog_is_open) {
dev_warn(&client->dev,
"i2c client detached with watchdog open! "
"Stopping watchdog.\n");
watchdog_disable(data);
}
mutex_lock(&watchdog_data_mutex);
list_del(&data->list);
mutex_unlock(&watchdog_data_mutex);
/* Tell the watchdog code the client is gone */
mutex_lock(&data->watchdog_lock);
data->client = NULL;
mutex_unlock(&data->watchdog_lock);
}
/* Reset Configuration Register to Disable Watch Dog Registers */
tmp = w83793_read_value(client, W83793_REG_CONFIG);
w83793_write_value(client, W83793_REG_CONFIG, tmp & ~0x04);
unregister_reboot_notifier(&watchdog_notifier);
hwmon_device_unregister(data->hwmon_dev);
for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++)
device_remove_file(dev,
&w83793_sensor_attr_2[i].dev_attr);
for (i = 0; i < ARRAY_SIZE(sda_single_files); i++)
device_remove_file(dev, &sda_single_files[i].dev_attr);
for (i = 0; i < ARRAY_SIZE(w83793_vid); i++)
device_remove_file(dev, &w83793_vid[i].dev_attr);
device_remove_file(dev, &dev_attr_vrm);
for (i = 0; i < ARRAY_SIZE(w83793_left_fan); i++)
device_remove_file(dev, &w83793_left_fan[i].dev_attr);
for (i = 0; i < ARRAY_SIZE(w83793_left_pwm); i++)
device_remove_file(dev, &w83793_left_pwm[i].dev_attr);
for (i = 0; i < ARRAY_SIZE(w83793_temp); i++)
device_remove_file(dev, &w83793_temp[i].dev_attr);
if (data->lm75[0] != NULL)
i2c_unregister_device(data->lm75[0]);
if (data->lm75[1] != NULL)
i2c_unregister_device(data->lm75[1]);
/* Decrease data reference counter */
mutex_lock(&watchdog_data_mutex);
kref_put(&data->kref, w83793_release_resources);
mutex_unlock(&watchdog_data_mutex);
return 0;
}
static int
w83793_detect_subclients(struct i2c_client *client)
{
int i, id, err;
int address = client->addr;
u8 tmp;
struct i2c_adapter *adapter = client->adapter;
struct w83793_data *data = i2c_get_clientdata(client);
id = i2c_adapter_id(adapter);
if (force_subclients[0] == id && force_subclients[1] == address) {
for (i = 2; i <= 3; i++) {
if (force_subclients[i] < 0x48
|| force_subclients[i] > 0x4f) {
dev_err(&client->dev,
"invalid subclient "
"address %d; must be 0x48-0x4f\n",
force_subclients[i]);
err = -EINVAL;
goto ERROR_SC_0;
}
}
w83793_write_value(client, W83793_REG_I2C_SUBADDR,
(force_subclients[2] & 0x07) |
((force_subclients[3] & 0x07) << 4));
}
tmp = w83793_read_value(client, W83793_REG_I2C_SUBADDR);
if (!(tmp & 0x08))
data->lm75[0] = i2c_new_dummy(adapter, 0x48 + (tmp & 0x7));
if (!(tmp & 0x80)) {
if ((data->lm75[0] != NULL)
&& ((tmp & 0x7) == ((tmp >> 4) & 0x7))) {
dev_err(&client->dev,
"duplicate addresses 0x%x, "
"use force_subclients\n", data->lm75[0]->addr);
err = -ENODEV;
goto ERROR_SC_1;
}
data->lm75[1] = i2c_new_dummy(adapter,
0x48 + ((tmp >> 4) & 0x7));
}
return 0;
/* Undo inits in case of errors */
ERROR_SC_1:
if (data->lm75[0] != NULL)
i2c_unregister_device(data->lm75[0]);
ERROR_SC_0:
return err;
}
/* Return 0 if detection is successful, -ENODEV otherwise */
static int w83793_detect(struct i2c_client *client,
struct i2c_board_info *info)
{
u8 tmp, bank, chip_id;
struct i2c_adapter *adapter = client->adapter;
unsigned short address = client->addr;
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
return -ENODEV;
bank = i2c_smbus_read_byte_data(client, W83793_REG_BANKSEL);
tmp = bank & 0x80 ? 0x5c : 0xa3;
/* Check Winbond vendor ID */
if (tmp != i2c_smbus_read_byte_data(client, W83793_REG_VENDORID)) {
pr_debug("w83793: Detection failed at check vendor id\n");
return -ENODEV;
}
/*
* If Winbond chip, address of chip and W83793_REG_I2C_ADDR
* should match
*/
if ((bank & 0x07) == 0
&& i2c_smbus_read_byte_data(client, W83793_REG_I2C_ADDR) !=
(address << 1)) {
pr_debug("w83793: Detection failed at check i2c addr\n");
return -ENODEV;
}
/* Determine the chip type now */
chip_id = i2c_smbus_read_byte_data(client, W83793_REG_CHIPID);
if (chip_id != 0x7b)
return -ENODEV;
strlcpy(info->type, "w83793", I2C_NAME_SIZE);
return 0;
}
static int w83793_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
const int watchdog_minors[] = { WATCHDOG_MINOR, 212, 213, 214, 215 };
struct w83793_data *data;
int i, tmp, val, err;
int files_fan = ARRAY_SIZE(w83793_left_fan) / 7;
int files_pwm = ARRAY_SIZE(w83793_left_pwm) / 5;
int files_temp = ARRAY_SIZE(w83793_temp) / 6;
data = kzalloc(sizeof(struct w83793_data), GFP_KERNEL);
if (!data) {
err = -ENOMEM;
goto exit;
}
i2c_set_clientdata(client, data);
data->bank = i2c_smbus_read_byte_data(client, W83793_REG_BANKSEL);
mutex_init(&data->update_lock);
mutex_init(&data->watchdog_lock);
INIT_LIST_HEAD(&data->list);
kref_init(&data->kref);
/*
* Store client pointer in our data struct for watchdog usage
* (where the client is found through a data ptr instead of the
* otherway around)
*/
data->client = client;
err = w83793_detect_subclients(client);
if (err)
goto free_mem;
/* Initialize the chip */
w83793_init_client(client);
/*
* Only fan 1-5 has their own input pins,
* Pwm 1-3 has their own pins
*/
data->has_fan = 0x1f;
data->has_pwm = 0x07;
tmp = w83793_read_value(client, W83793_REG_MFC);
val = w83793_read_value(client, W83793_REG_FANIN_CTRL);
/* check the function of pins 49-56 */
if (tmp & 0x80) {
data->has_vid |= 0x2; /* has VIDB */
} else {
data->has_pwm |= 0x18; /* pwm 4,5 */
if (val & 0x01) { /* fan 6 */
data->has_fan |= 0x20;
data->has_pwm |= 0x20;
}
if (val & 0x02) { /* fan 7 */
data->has_fan |= 0x40;
data->has_pwm |= 0x40;
}
if (!(tmp & 0x40) && (val & 0x04)) { /* fan 8 */
data->has_fan |= 0x80;
data->has_pwm |= 0x80;
}
}
/* check the function of pins 37-40 */
if (!(tmp & 0x29))
data->has_vid |= 0x1; /* has VIDA */
if (0x08 == (tmp & 0x0c)) {
if (val & 0x08) /* fan 9 */
data->has_fan |= 0x100;
if (val & 0x10) /* fan 10 */
data->has_fan |= 0x200;
}
if (0x20 == (tmp & 0x30)) {
if (val & 0x20) /* fan 11 */
data->has_fan |= 0x400;
if (val & 0x40) /* fan 12 */
data->has_fan |= 0x800;
}
if ((tmp & 0x01) && (val & 0x04)) { /* fan 8, second location */
data->has_fan |= 0x80;
data->has_pwm |= 0x80;
}
tmp = w83793_read_value(client, W83793_REG_FANIN_SEL);
if ((tmp & 0x01) && (val & 0x08)) { /* fan 9, second location */
data->has_fan |= 0x100;
}
if ((tmp & 0x02) && (val & 0x10)) { /* fan 10, second location */
data->has_fan |= 0x200;
}
if ((tmp & 0x04) && (val & 0x20)) { /* fan 11, second location */
data->has_fan |= 0x400;
}
if ((tmp & 0x08) && (val & 0x40)) { /* fan 12, second location */
data->has_fan |= 0x800;
}
/* check the temp1-6 mode, ignore former AMDSI selected inputs */
tmp = w83793_read_value(client, W83793_REG_TEMP_MODE[0]);
if (tmp & 0x01)
data->has_temp |= 0x01;
if (tmp & 0x04)
data->has_temp |= 0x02;
if (tmp & 0x10)
data->has_temp |= 0x04;
if (tmp & 0x40)
data->has_temp |= 0x08;
tmp = w83793_read_value(client, W83793_REG_TEMP_MODE[1]);
if (tmp & 0x01)
data->has_temp |= 0x10;
if (tmp & 0x02)
data->has_temp |= 0x20;
/* Register sysfs hooks */
for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++) {
err = device_create_file(dev,
&w83793_sensor_attr_2[i].dev_attr);
if (err)
goto exit_remove;
}
for (i = 0; i < ARRAY_SIZE(w83793_vid); i++) {
if (!(data->has_vid & (1 << i)))
continue;
err = device_create_file(dev, &w83793_vid[i].dev_attr);
if (err)
goto exit_remove;
}
if (data->has_vid) {
data->vrm = vid_which_vrm();
err = device_create_file(dev, &dev_attr_vrm);
if (err)
goto exit_remove;
}
for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) {
err = device_create_file(dev, &sda_single_files[i].dev_attr);
if (err)
goto exit_remove;
}
for (i = 0; i < 6; i++) {
int j;
if (!(data->has_temp & (1 << i)))
continue;
for (j = 0; j < files_temp; j++) {
err = device_create_file(dev,
&w83793_temp[(i) * files_temp
+ j].dev_attr);
if (err)
goto exit_remove;
}
}
for (i = 5; i < 12; i++) {
int j;
if (!(data->has_fan & (1 << i)))
continue;
for (j = 0; j < files_fan; j++) {
err = device_create_file(dev,
&w83793_left_fan[(i - 5) * files_fan
+ j].dev_attr);
if (err)
goto exit_remove;
}
}
for (i = 3; i < 8; i++) {
int j;
if (!(data->has_pwm & (1 << i)))
continue;
for (j = 0; j < files_pwm; j++) {
err = device_create_file(dev,
&w83793_left_pwm[(i - 3) * files_pwm
+ j].dev_attr);
if (err)
goto exit_remove;
}
}
data->hwmon_dev = hwmon_device_register(dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
goto exit_remove;
}
/* Watchdog initialization */
/* Register boot notifier */
err = register_reboot_notifier(&watchdog_notifier);
if (err != 0) {
dev_err(&client->dev,
"cannot register reboot notifier (err=%d)\n", err);
goto exit_devunreg;
}
/*
* Enable Watchdog registers.
* Set Configuration Register to Enable Watch Dog Registers
* (Bit 2) = XXXX, X1XX.
*/
tmp = w83793_read_value(client, W83793_REG_CONFIG);
w83793_write_value(client, W83793_REG_CONFIG, tmp | 0x04);
/* Set the default watchdog timeout */
data->watchdog_timeout = timeout;
/* Check, if last reboot was caused by watchdog */
data->watchdog_caused_reboot =
w83793_read_value(data->client, W83793_REG_WDT_STATUS) & 0x01;
/* Disable Soft Watchdog during initialiation */
watchdog_disable(data);
/*
* We take the data_mutex lock early so that watchdog_open() cannot
* run when misc_register() has completed, but we've not yet added
* our data to the watchdog_data_list (and set the default timeout)
*/
mutex_lock(&watchdog_data_mutex);
for (i = 0; i < ARRAY_SIZE(watchdog_minors); i++) {
/* Register our watchdog part */
snprintf(data->watchdog_name, sizeof(data->watchdog_name),
"watchdog%c", (i == 0) ? '\0' : ('0' + i));
data->watchdog_miscdev.name = data->watchdog_name;
data->watchdog_miscdev.fops = &watchdog_fops;
data->watchdog_miscdev.minor = watchdog_minors[i];
err = misc_register(&data->watchdog_miscdev);
if (err == -EBUSY)
continue;
if (err) {
data->watchdog_miscdev.minor = 0;
dev_err(&client->dev,
"Registering watchdog chardev: %d\n", err);
break;
}
list_add(&data->list, &watchdog_data_list);
dev_info(&client->dev,
"Registered watchdog chardev major 10, minor: %d\n",
watchdog_minors[i]);
break;
}
if (i == ARRAY_SIZE(watchdog_minors)) {
data->watchdog_miscdev.minor = 0;
dev_warn(&client->dev,
"Couldn't register watchdog chardev (due to no free minor)\n");
}
mutex_unlock(&watchdog_data_mutex);
return 0;
/* Unregister hwmon device */
exit_devunreg:
hwmon_device_unregister(data->hwmon_dev);
/* Unregister sysfs hooks */
exit_remove:
for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++)
device_remove_file(dev, &w83793_sensor_attr_2[i].dev_attr);
for (i = 0; i < ARRAY_SIZE(sda_single_files); i++)
device_remove_file(dev, &sda_single_files[i].dev_attr);
for (i = 0; i < ARRAY_SIZE(w83793_vid); i++)
device_remove_file(dev, &w83793_vid[i].dev_attr);
for (i = 0; i < ARRAY_SIZE(w83793_left_fan); i++)
device_remove_file(dev, &w83793_left_fan[i].dev_attr);
for (i = 0; i < ARRAY_SIZE(w83793_left_pwm); i++)
device_remove_file(dev, &w83793_left_pwm[i].dev_attr);
for (i = 0; i < ARRAY_SIZE(w83793_temp); i++)
device_remove_file(dev, &w83793_temp[i].dev_attr);
if (data->lm75[0] != NULL)
i2c_unregister_device(data->lm75[0]);
if (data->lm75[1] != NULL)
i2c_unregister_device(data->lm75[1]);
free_mem:
kfree(data);
exit:
return err;
}
static void w83793_update_nonvolatile(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
int i, j;
/*
* They are somewhat "stable" registers, and to update them every time
* takes so much time, it's just not worthy. Update them in a long
* interval to avoid exception.
*/
if (!(time_after(jiffies, data->last_nonvolatile + HZ * 300)
|| !data->valid))
return;
/* update voltage limits */
for (i = 1; i < 3; i++) {
for (j = 0; j < ARRAY_SIZE(data->in); j++) {
data->in[j][i] =
w83793_read_value(client, W83793_REG_IN[j][i]);
}
data->in_low_bits[i] =
w83793_read_value(client, W83793_REG_IN_LOW_BITS[i]);
}
for (i = 0; i < ARRAY_SIZE(data->fan_min); i++) {
/* Update the Fan measured value and limits */
if (!(data->has_fan & (1 << i)))
continue;
data->fan_min[i] =
w83793_read_value(client, W83793_REG_FAN_MIN(i)) << 8;
data->fan_min[i] |=
w83793_read_value(client, W83793_REG_FAN_MIN(i) + 1);
}
for (i = 0; i < ARRAY_SIZE(data->temp_fan_map); i++) {
if (!(data->has_temp & (1 << i)))
continue;
data->temp_fan_map[i] =
w83793_read_value(client, W83793_REG_TEMP_FAN_MAP(i));
for (j = 1; j < 5; j++) {
data->temp[i][j] =
w83793_read_value(client, W83793_REG_TEMP[i][j]);
}
data->temp_cruise[i] =
w83793_read_value(client, W83793_REG_TEMP_CRUISE(i));
for (j = 0; j < 7; j++) {
data->sf2_pwm[i][j] =
w83793_read_value(client, W83793_REG_SF2_PWM(i, j));
data->sf2_temp[i][j] =
w83793_read_value(client,
W83793_REG_SF2_TEMP(i, j));
}
}
for (i = 0; i < ARRAY_SIZE(data->temp_mode); i++)
data->temp_mode[i] =
w83793_read_value(client, W83793_REG_TEMP_MODE[i]);
for (i = 0; i < ARRAY_SIZE(data->tolerance); i++) {
data->tolerance[i] =
w83793_read_value(client, W83793_REG_TEMP_TOL(i));
}
for (i = 0; i < ARRAY_SIZE(data->pwm); i++) {
if (!(data->has_pwm & (1 << i)))
continue;
data->pwm[i][PWM_NONSTOP] =
w83793_read_value(client, W83793_REG_PWM(i, PWM_NONSTOP));
data->pwm[i][PWM_START] =
w83793_read_value(client, W83793_REG_PWM(i, PWM_START));
data->pwm_stop_time[i] =
w83793_read_value(client, W83793_REG_PWM_STOP_TIME(i));
}
data->pwm_default = w83793_read_value(client, W83793_REG_PWM_DEFAULT);
data->pwm_enable = w83793_read_value(client, W83793_REG_PWM_ENABLE);
data->pwm_uptime = w83793_read_value(client, W83793_REG_PWM_UPTIME);
data->pwm_downtime = w83793_read_value(client, W83793_REG_PWM_DOWNTIME);
data->temp_critical =
w83793_read_value(client, W83793_REG_TEMP_CRITICAL);
data->beep_enable = w83793_read_value(client, W83793_REG_OVT_BEEP);
for (i = 0; i < ARRAY_SIZE(data->beeps); i++)
data->beeps[i] = w83793_read_value(client, W83793_REG_BEEP(i));
data->last_nonvolatile = jiffies;
}
static struct w83793_data *w83793_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
int i;
mutex_lock(&data->update_lock);
if (!(time_after(jiffies, data->last_updated + HZ * 2)
|| !data->valid))
goto END;
/* Update the voltages measured value and limits */
for (i = 0; i < ARRAY_SIZE(data->in); i++)
data->in[i][IN_READ] =
w83793_read_value(client, W83793_REG_IN[i][IN_READ]);
data->in_low_bits[IN_READ] =
w83793_read_value(client, W83793_REG_IN_LOW_BITS[IN_READ]);
for (i = 0; i < ARRAY_SIZE(data->fan); i++) {
if (!(data->has_fan & (1 << i)))
continue;
data->fan[i] =
w83793_read_value(client, W83793_REG_FAN(i)) << 8;
data->fan[i] |=
w83793_read_value(client, W83793_REG_FAN(i) + 1);
}
for (i = 0; i < ARRAY_SIZE(data->temp); i++) {
if (!(data->has_temp & (1 << i)))
continue;
data->temp[i][TEMP_READ] =
w83793_read_value(client, W83793_REG_TEMP[i][TEMP_READ]);
}
data->temp_low_bits =
w83793_read_value(client, W83793_REG_TEMP_LOW_BITS);
for (i = 0; i < ARRAY_SIZE(data->pwm); i++) {
if (data->has_pwm & (1 << i))
data->pwm[i][PWM_DUTY] =
w83793_read_value(client,
W83793_REG_PWM(i, PWM_DUTY));
}
for (i = 0; i < ARRAY_SIZE(data->alarms); i++)
data->alarms[i] =
w83793_read_value(client, W83793_REG_ALARM(i));
if (data->has_vid & 0x01)
data->vid[0] = w83793_read_value(client, W83793_REG_VID_INA);
if (data->has_vid & 0x02)
data->vid[1] = w83793_read_value(client, W83793_REG_VID_INB);
w83793_update_nonvolatile(dev);
data->last_updated = jiffies;
data->valid = 1;
END:
mutex_unlock(&data->update_lock);
return data;
}
/*
* Ignore the possibility that somebody change bank outside the driver
* Must be called with data->update_lock held, except during initialization
*/
static u8 w83793_read_value(struct i2c_client *client, u16 reg)
{
struct w83793_data *data = i2c_get_clientdata(client);
u8 res = 0xff;
u8 new_bank = reg >> 8;
new_bank |= data->bank & 0xfc;
if (data->bank != new_bank) {
if (i2c_smbus_write_byte_data
(client, W83793_REG_BANKSEL, new_bank) >= 0)
data->bank = new_bank;
else {
dev_err(&client->dev,
"set bank to %d failed, fall back "
"to bank %d, read reg 0x%x error\n",
new_bank, data->bank, reg);
res = 0x0; /* read 0x0 from the chip */
goto END;
}
}
res = i2c_smbus_read_byte_data(client, reg & 0xff);
END:
return res;
}
/* Must be called with data->update_lock held, except during initialization */
static int w83793_write_value(struct i2c_client *client, u16 reg, u8 value)
{
struct w83793_data *data = i2c_get_clientdata(client);
int res;
u8 new_bank = reg >> 8;
new_bank |= data->bank & 0xfc;
if (data->bank != new_bank) {
res = i2c_smbus_write_byte_data(client, W83793_REG_BANKSEL,
new_bank);
if (res < 0) {
dev_err(&client->dev,
"set bank to %d failed, fall back "
"to bank %d, write reg 0x%x error\n",
new_bank, data->bank, reg);
goto END;
}
data->bank = new_bank;
}
res = i2c_smbus_write_byte_data(client, reg & 0xff, value);
END:
return res;
}
module_i2c_driver(w83793_driver);
MODULE_AUTHOR("Yuan Mu, Sven Anders");
MODULE_DESCRIPTION("w83793 driver");
MODULE_LICENSE("GPL");
