// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2017, The Linux Foundation. All rights reserved.
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/nvmem-consumer.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/reset.h>
#include <linux/slab.h>
#include <dt-bindings/phy/phy-qcom-qusb2.h>
#define QUSB2PHY_PLL_TEST 0x04
#define CLK_REF_SEL BIT(7)
#define QUSB2PHY_PLL_TUNE 0x08
#define QUSB2PHY_PLL_USER_CTL1 0x0c
#define QUSB2PHY_PLL_USER_CTL2 0x10
#define QUSB2PHY_PLL_AUTOPGM_CTL1 0x1c
#define QUSB2PHY_PLL_PWR_CTRL 0x18
/* QUSB2PHY_PLL_STATUS register bits */
#define PLL_LOCKED BIT(5)
/* QUSB2PHY_PLL_COMMON_STATUS_ONE register bits */
#define CORE_READY_STATUS BIT(0)
/* QUSB2PHY_PORT_POWERDOWN register bits */
#define CLAMP_N_EN BIT(5)
#define FREEZIO_N BIT(1)
#define POWER_DOWN BIT(0)
/* QUSB2PHY_PWR_CTRL1 register bits */
#define PWR_CTRL1_VREF_SUPPLY_TRIM BIT(5)
#define PWR_CTRL1_CLAMP_N_EN BIT(1)
#define QUSB2PHY_REFCLK_ENABLE BIT(0)
#define PHY_CLK_SCHEME_SEL BIT(0)
/* QUSB2PHY_INTR_CTRL register bits */
#define DMSE_INTR_HIGH_SEL BIT(4)
#define DPSE_INTR_HIGH_SEL BIT(3)
#define CHG_DET_INTR_EN BIT(2)
#define DMSE_INTR_EN BIT(1)
#define DPSE_INTR_EN BIT(0)
/* QUSB2PHY_PLL_CORE_INPUT_OVERRIDE register bits */
#define CORE_PLL_EN_FROM_RESET BIT(4)
#define CORE_RESET BIT(5)
#define CORE_RESET_MUX BIT(6)
/* QUSB2PHY_IMP_CTRL1 register bits */
#define IMP_RES_OFFSET_MASK GENMASK(5, 0)
#define IMP_RES_OFFSET_SHIFT 0x0
/* QUSB2PHY_PORT_TUNE1 register bits */
#define HSTX_TRIM_MASK GENMASK(7, 4)
#define HSTX_TRIM_SHIFT 0x4
#define PREEMPH_WIDTH_HALF_BIT BIT(2)
#define PREEMPHASIS_EN_MASK GENMASK(1, 0)
#define PREEMPHASIS_EN_SHIFT 0x0
#define QUSB2PHY_PLL_ANALOG_CONTROLS_TWO 0x04
#define QUSB2PHY_PLL_CLOCK_INVERTERS 0x18c
#define QUSB2PHY_PLL_CMODE 0x2c
#define QUSB2PHY_PLL_LOCK_DELAY 0x184
#define QUSB2PHY_PLL_DIGITAL_TIMERS_TWO 0xb4
#define QUSB2PHY_PLL_BIAS_CONTROL_1 0x194
#define QUSB2PHY_PLL_BIAS_CONTROL_2 0x198
#define QUSB2PHY_PWR_CTRL2 0x214
#define QUSB2PHY_IMP_CTRL1 0x220
#define QUSB2PHY_IMP_CTRL2 0x224
#define QUSB2PHY_CHG_CTRL2 0x23c
struct qusb2_phy_init_tbl {
unsigned int offset;
unsigned int val;
/*
* register part of layout ?
* if yes, then offset gives index in the reg-layout
*/
int in_layout;
};
#define QUSB2_PHY_INIT_CFG(o, v) \
{ \
.offset = o, \
.val = v, \
}
#define QUSB2_PHY_INIT_CFG_L(o, v) \
{ \
.offset = o, \
.val = v, \
.in_layout = 1, \
}
/* set of registers with offsets different per-PHY */
enum qusb2phy_reg_layout {
QUSB2PHY_PLL_CORE_INPUT_OVERRIDE,
QUSB2PHY_PLL_STATUS,
QUSB2PHY_PORT_TUNE1,
QUSB2PHY_PORT_TUNE2,
QUSB2PHY_PORT_TUNE3,
QUSB2PHY_PORT_TUNE4,
QUSB2PHY_PORT_TUNE5,
QUSB2PHY_PORT_TEST1,
QUSB2PHY_PORT_TEST2,
QUSB2PHY_PORT_POWERDOWN,
QUSB2PHY_INTR_CTRL,
};
static const unsigned int msm8996_regs_layout[] = {
[QUSB2PHY_PLL_STATUS] = 0x38,
[QUSB2PHY_PORT_TUNE1] = 0x80,
[QUSB2PHY_PORT_TUNE2] = 0x84,
[QUSB2PHY_PORT_TUNE3] = 0x88,
[QUSB2PHY_PORT_TUNE4] = 0x8c,
[QUSB2PHY_PORT_TUNE5] = 0x90,
[QUSB2PHY_PORT_TEST1] = 0xb8,
[QUSB2PHY_PORT_TEST2] = 0x9c,
[QUSB2PHY_PORT_POWERDOWN] = 0xb4,
[QUSB2PHY_INTR_CTRL] = 0xbc,
};
static const struct qusb2_phy_init_tbl msm8996_init_tbl[] = {
QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xf8),
QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0xb3),
QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0x83),
QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0xc0),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TUNE, 0x30),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL1, 0x79),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL2, 0x21),
QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TEST2, 0x14),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_AUTOPGM_CTL1, 0x9f),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00),
};
static const unsigned int sdm845_regs_layout[] = {
[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8,
[QUSB2PHY_PLL_STATUS] = 0x1a0,
[QUSB2PHY_PORT_TUNE1] = 0x240,
[QUSB2PHY_PORT_TUNE2] = 0x244,
[QUSB2PHY_PORT_TUNE3] = 0x248,
[QUSB2PHY_PORT_TUNE4] = 0x24c,
[QUSB2PHY_PORT_TUNE5] = 0x250,
[QUSB2PHY_PORT_TEST1] = 0x254,
[QUSB2PHY_PORT_TEST2] = 0x258,
[QUSB2PHY_PORT_POWERDOWN] = 0x210,
[QUSB2PHY_INTR_CTRL] = 0x230,
};
static const struct qusb2_phy_init_tbl sdm845_init_tbl[] = {
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x03),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_1, 0x40),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_2, 0x20),
QUSB2_PHY_INIT_CFG(QUSB2PHY_PWR_CTRL2, 0x21),
QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL1, 0x0),
QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL2, 0x58),
QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0x30),
QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x29),
QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0xca),
QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0x04),
QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE5, 0x03),
QUSB2_PHY_INIT_CFG(QUSB2PHY_CHG_CTRL2, 0x0),
};
struct qusb2_phy_cfg {
const struct qusb2_phy_init_tbl *tbl;
/* number of entries in the table */
unsigned int tbl_num;
/* offset to PHY_CLK_SCHEME register in TCSR map */
unsigned int clk_scheme_offset;
/* array of registers with different offsets */
const unsigned int *regs;
unsigned int mask_core_ready;
unsigned int disable_ctrl;
unsigned int autoresume_en;
/* true if PHY has PLL_TEST register to select clk_scheme */
bool has_pll_test;
/* true if TUNE1 register must be updated by fused value, else TUNE2 */
bool update_tune1_with_efuse;
/* true if PHY has PLL_CORE_INPUT_OVERRIDE register to reset PLL */
bool has_pll_override;
};
static const struct qusb2_phy_cfg msm8996_phy_cfg = {
.tbl = msm8996_init_tbl,
.tbl_num = ARRAY_SIZE(msm8996_init_tbl),
.regs = msm8996_regs_layout,
.has_pll_test = true,
.disable_ctrl = (CLAMP_N_EN | FREEZIO_N | POWER_DOWN),
.mask_core_ready = PLL_LOCKED,
.autoresume_en = BIT(3),
};
static const struct qusb2_phy_cfg sdm845_phy_cfg = {
.tbl = sdm845_init_tbl,
.tbl_num = ARRAY_SIZE(sdm845_init_tbl),
.regs = sdm845_regs_layout,
.disable_ctrl = (PWR_CTRL1_VREF_SUPPLY_TRIM | PWR_CTRL1_CLAMP_N_EN |
POWER_DOWN),
.mask_core_ready = CORE_READY_STATUS,
.has_pll_override = true,
.autoresume_en = BIT(0),
};
static const char * const qusb2_phy_vreg_names[] = {
"vdda-pll", "vdda-phy-dpdm",
};
#define QUSB2_NUM_VREGS ARRAY_SIZE(qusb2_phy_vreg_names)
/**
* struct qusb2_phy - structure holding qusb2 phy attributes
*
* @phy: generic phy
* @base: iomapped memory space for qubs2 phy
*
* @cfg_ahb_clk: AHB2PHY interface clock
* @ref_clk: phy reference clock
* @iface_clk: phy interface clock
* @phy_reset: phy reset control
* @vregs: regulator supplies bulk data
*
* @tcsr: TCSR syscon register map
* @cell: nvmem cell containing phy tuning value
*
* @override_imp_res_offset: PHY should use different rescode offset
* @imp_res_offset_value: rescode offset to be updated in IMP_CTRL1 register
* @override_hstx_trim: PHY should use different HSTX o/p current value
* @hstx_trim_value: HSTX_TRIM value to be updated in TUNE1 register
* @override_preemphasis: PHY should use different pre-amphasis amplitude
* @preemphasis_level: Amplitude Pre-Emphasis to be updated in TUNE1 register
* @override_preemphasis_width: PHY should use different pre-emphasis duration
* @preemphasis_width: half/full-width Pre-Emphasis updated via TUNE1
*
* @cfg: phy config data
* @has_se_clk_scheme: indicate if PHY has single-ended ref clock scheme
* @phy_initialized: indicate if PHY has been initialized
* @mode: current PHY mode
*/
struct qusb2_phy {
struct phy *phy;
void __iomem *base;
struct clk *cfg_ahb_clk;
struct clk *ref_clk;
struct clk *iface_clk;
struct reset_control *phy_reset;
struct regulator_bulk_data vregs[QUSB2_NUM_VREGS];
struct regmap *tcsr;
struct nvmem_cell *cell;
bool override_imp_res_offset;
u8 imp_res_offset_value;
bool override_hstx_trim;
u8 hstx_trim_value;
bool override_preemphasis;
u8 preemphasis_level;
bool override_preemphasis_width;
u8 preemphasis_width;
const struct qusb2_phy_cfg *cfg;
bool has_se_clk_scheme;
bool phy_initialized;
enum phy_mode mode;
};
static inline void qusb2_write_mask(void __iomem *base, u32 offset,
u32 val, u32 mask)
{
u32 reg;
reg = readl(base + offset);
reg &= ~mask;
reg |= val & mask;
writel(reg, base + offset);
/* Ensure above write is completed */
readl(base + offset);
}
static inline void qusb2_setbits(void __iomem *base, u32 offset, u32 val)
{
u32 reg;
reg = readl(base + offset);
reg |= val;
writel(reg, base + offset);
/* Ensure above write is completed */
readl(base + offset);
}
static inline void qusb2_clrbits(void __iomem *base, u32 offset, u32 val)
{
u32 reg;
reg = readl(base + offset);
reg &= ~val;
writel(reg, base + offset);
/* Ensure above write is completed */
readl(base + offset);
}
static inline
void qcom_qusb2_phy_configure(void __iomem *base,
const unsigned int *regs,
const struct qusb2_phy_init_tbl tbl[], int num)
{
int i;
for (i = 0; i < num; i++) {
if (tbl[i].in_layout)
writel(tbl[i].val, base + regs[tbl[i].offset]);
else
writel(tbl[i].val, base + tbl[i].offset);
}
}
/*
* Update board specific PHY tuning override values if specified from
* device tree.
*/
static void qusb2_phy_override_phy_params(struct qusb2_phy *qphy)
{
const struct qusb2_phy_cfg *cfg = qphy->cfg;
if (qphy->override_imp_res_offset)
qusb2_write_mask(qphy->base, QUSB2PHY_IMP_CTRL1,
qphy->imp_res_offset_value << IMP_RES_OFFSET_SHIFT,
IMP_RES_OFFSET_MASK);
if (qphy->override_hstx_trim)
qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1],
qphy->hstx_trim_value << HSTX_TRIM_SHIFT,
HSTX_TRIM_MASK);
if (qphy->override_preemphasis)
qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1],
qphy->preemphasis_level << PREEMPHASIS_EN_SHIFT,
PREEMPHASIS_EN_MASK);
if (qphy->override_preemphasis_width) {
if (qphy->preemphasis_width ==
QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT)
qusb2_setbits(qphy->base,
cfg->regs[QUSB2PHY_PORT_TUNE1],
PREEMPH_WIDTH_HALF_BIT);
else
qusb2_clrbits(qphy->base,
cfg->regs[QUSB2PHY_PORT_TUNE1],
PREEMPH_WIDTH_HALF_BIT);
}
}
/*
* Fetches HS Tx tuning value from nvmem and sets the
* QUSB2PHY_PORT_TUNE1/2 register.
* For error case, skip setting the value and use the default value.
*/
static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy)
{
struct device *dev = &qphy->phy->dev;
const struct qusb2_phy_cfg *cfg = qphy->cfg;
u8 *val;
/* efuse register is optional */
if (!qphy->cell)
return;
/*
* Read efuse register having TUNE2/1 parameter's high nibble.
* If efuse register shows value as 0x0, or if we fail to find
* a valid efuse register settings, then use default value
* as 0xB for high nibble that we have already set while
* configuring phy.
*/
val = nvmem_cell_read(qphy->cell, NULL);
if (IS_ERR(val) || !val[0]) {
dev_dbg(dev, "failed to read a valid hs-tx trim value\n");
return;
}
/* Fused TUNE1/2 value is the higher nibble only */
if (cfg->update_tune1_with_efuse)
qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1],
val[0] << 0x4);
else
qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE2],
val[0] << 0x4);
}
static int qusb2_phy_set_mode(struct phy *phy, enum phy_mode mode)
{
struct qusb2_phy *qphy = phy_get_drvdata(phy);
qphy->mode = mode;
return 0;
}
static int __maybe_unused qusb2_phy_runtime_suspend(struct device *dev)
{
struct qusb2_phy *qphy = dev_get_drvdata(dev);
const struct qusb2_phy_cfg *cfg = qphy->cfg;
u32 intr_mask;
dev_vdbg(dev, "Suspending QUSB2 Phy, mode:%d\n", qphy->mode);
if (!qphy->phy_initialized) {
dev_vdbg(dev, "PHY not initialized, bailing out\n");
return 0;
}
/*
* Enable DP/DM interrupts to detect line state changes based on current
* speed. In other words, enable the triggers _opposite_ of what the
* current D+/D- levels are e.g. if currently D+ high, D- low
* (HS 'J'/Suspend), configure the mask to trigger on D+ low OR D- high
*/
intr_mask = DPSE_INTR_EN | DMSE_INTR_EN;
switch (qphy->mode) {
case PHY_MODE_USB_HOST_HS:
case PHY_MODE_USB_HOST_FS:
case PHY_MODE_USB_DEVICE_HS:
case PHY_MODE_USB_DEVICE_FS:
intr_mask |= DMSE_INTR_HIGH_SEL;
break;
case PHY_MODE_USB_HOST_LS:
case PHY_MODE_USB_DEVICE_LS:
intr_mask |= DPSE_INTR_HIGH_SEL;
break;
default:
/* No device connected, enable both DP/DM high interrupt */
intr_mask |= DMSE_INTR_HIGH_SEL;
intr_mask |= DPSE_INTR_HIGH_SEL;
break;
}
writel(intr_mask, qphy->base + cfg->regs[QUSB2PHY_INTR_CTRL]);
/* hold core PLL into reset */
if (cfg->has_pll_override) {
qusb2_setbits(qphy->base,
cfg->regs[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE],
CORE_PLL_EN_FROM_RESET | CORE_RESET |
CORE_RESET_MUX);
}
/* enable phy auto-resume only if device is connected on bus */
if (qphy->mode != PHY_MODE_INVALID) {
qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TEST1],
cfg->autoresume_en);
/* Autoresume bit has to be toggled in order to enable it */
qusb2_clrbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TEST1],
cfg->autoresume_en);
}
if (!qphy->has_se_clk_scheme)
clk_disable_unprepare(qphy->ref_clk);
clk_disable_unprepare(qphy->cfg_ahb_clk);
clk_disable_unprepare(qphy->iface_clk);
return 0;
}
static int __maybe_unused qusb2_phy_runtime_resume(struct device *dev)
{
struct qusb2_phy *qphy = dev_get_drvdata(dev);
const struct qusb2_phy_cfg *cfg = qphy->cfg;
int ret;
dev_vdbg(dev, "Resuming QUSB2 phy, mode:%d\n", qphy->mode);
if (!qphy->phy_initialized) {
dev_vdbg(dev, "PHY not initialized, bailing out\n");
return 0;
}
ret = clk_prepare_enable(qphy->iface_clk);
if (ret) {
dev_err(dev, "failed to enable iface_clk, %d\n", ret);
return ret;
}
ret = clk_prepare_enable(qphy->cfg_ahb_clk);
if (ret) {
dev_err(dev, "failed to enable cfg ahb clock, %d\n", ret);
goto disable_iface_clk;
}
if (!qphy->has_se_clk_scheme) {
clk_prepare_enable(qphy->ref_clk);
if (ret) {
dev_err(dev, "failed to enable ref clk, %d\n", ret);
goto disable_ahb_clk;
}
}
writel(0x0, qphy->base + cfg->regs[QUSB2PHY_INTR_CTRL]);
/* bring core PLL out of reset */
if (cfg->has_pll_override) {
qusb2_clrbits(qphy->base,
cfg->regs[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE],
CORE_RESET | CORE_RESET_MUX);
}
return 0;
disable_ahb_clk:
clk_disable_unprepare(qphy->cfg_ahb_clk);
disable_iface_clk:
clk_disable_unprepare(qphy->iface_clk);
return ret;
}
static int qusb2_phy_init(struct phy *phy)
{
struct qusb2_phy *qphy = phy_get_drvdata(phy);
const struct qusb2_phy_cfg *cfg = qphy->cfg;
unsigned int val = 0;
unsigned int clk_scheme;
int ret;
dev_vdbg(&phy->dev, "%s(): Initializing QUSB2 phy\n", __func__);
/* turn on regulator supplies */
ret = regulator_bulk_enable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
if (ret)
return ret;
ret = clk_prepare_enable(qphy->iface_clk);
if (ret) {
dev_err(&phy->dev, "failed to enable iface_clk, %d\n", ret);
goto poweroff_phy;
}
/* enable ahb interface clock to program phy */
ret = clk_prepare_enable(qphy->cfg_ahb_clk);
if (ret) {
dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret);
goto disable_iface_clk;
}
/* Perform phy reset */
ret = reset_control_assert(qphy->phy_reset);
if (ret) {
dev_err(&phy->dev, "failed to assert phy_reset, %d\n", ret);
goto disable_ahb_clk;
}
/* 100 us delay to keep PHY in reset mode */
usleep_range(100, 150);
ret = reset_control_deassert(qphy->phy_reset);
if (ret) {
dev_err(&phy->dev, "failed to de-assert phy_reset, %d\n", ret);
goto disable_ahb_clk;
}
/* Disable the PHY */
qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_POWERDOWN],
qphy->cfg->disable_ctrl);
if (cfg->has_pll_test) {
/* save reset value to override reference clock scheme later */
val = readl(qphy->base + QUSB2PHY_PLL_TEST);
}
qcom_qusb2_phy_configure(qphy->base, cfg->regs, cfg->tbl,
cfg->tbl_num);
/* Override board specific PHY tuning values */
qusb2_phy_override_phy_params(qphy);
/* Set efuse value for tuning the PHY */
qusb2_phy_set_tune2_param(qphy);
/* Enable the PHY */
qusb2_clrbits(qphy->base, cfg->regs[QUSB2PHY_PORT_POWERDOWN],
POWER_DOWN);
/* Required to get phy pll lock successfully */
usleep_range(150, 160);
/* Default is single-ended clock on msm8996 */
qphy->has_se_clk_scheme = true;
/*
* read TCSR_PHY_CLK_SCHEME register to check if single-ended
* clock scheme is selected. If yes, then disable differential
* ref_clk and use single-ended clock, otherwise use differential
* ref_clk only.
*/
if (qphy->tcsr) {
ret = regmap_read(qphy->tcsr, qphy->cfg->clk_scheme_offset,
&clk_scheme);
if (ret) {
dev_err(&phy->dev, "failed to read clk scheme reg\n");
goto assert_phy_reset;
}
/* is it a differential clock scheme ? */
if (!(clk_scheme & PHY_CLK_SCHEME_SEL)) {
dev_vdbg(&phy->dev, "%s(): select differential clk\n",
__func__);
qphy->has_se_clk_scheme = false;
} else {
dev_vdbg(&phy->dev, "%s(): select single-ended clk\n",
__func__);
}
}
if (!qphy->has_se_clk_scheme) {
ret = clk_prepare_enable(qphy->ref_clk);
if (ret) {
dev_err(&phy->dev, "failed to enable ref clk, %d\n",
ret);
goto assert_phy_reset;
}
}
if (cfg->has_pll_test) {
if (!qphy->has_se_clk_scheme)
val &= ~CLK_REF_SEL;
else
val |= CLK_REF_SEL;
writel(val, qphy->base + QUSB2PHY_PLL_TEST);
/* ensure above write is through */
readl(qphy->base + QUSB2PHY_PLL_TEST);
}
/* Required to get phy pll lock successfully */
usleep_range(100, 110);
val = readb(qphy->base + cfg->regs[QUSB2PHY_PLL_STATUS]);
if (!(val & cfg->mask_core_ready)) {
dev_err(&phy->dev,
"QUSB2PHY pll lock failed: status reg = %x\n", val);
ret = -EBUSY;
goto disable_ref_clk;
}
qphy->phy_initialized = true;
return 0;
disable_ref_clk:
if (!qphy->has_se_clk_scheme)
clk_disable_unprepare(qphy->ref_clk);
assert_phy_reset:
reset_control_assert(qphy->phy_reset);
disable_ahb_clk:
clk_disable_unprepare(qphy->cfg_ahb_clk);
disable_iface_clk:
clk_disable_unprepare(qphy->iface_clk);
poweroff_phy:
regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
return ret;
}
static int qusb2_phy_exit(struct phy *phy)
{
struct qusb2_phy *qphy = phy_get_drvdata(phy);
/* Disable the PHY */
qusb2_setbits(qphy->base, qphy->cfg->regs[QUSB2PHY_PORT_POWERDOWN],
qphy->cfg->disable_ctrl);
if (!qphy->has_se_clk_scheme)
clk_disable_unprepare(qphy->ref_clk);
reset_control_assert(qphy->phy_reset);
clk_disable_unprepare(qphy->cfg_ahb_clk);
clk_disable_unprepare(qphy->iface_clk);
regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
qphy->phy_initialized = false;
return 0;
}
static const struct phy_ops qusb2_phy_gen_ops = {
.init = qusb2_phy_init,
.exit = qusb2_phy_exit,
.set_mode = qusb2_phy_set_mode,
.owner = THIS_MODULE,
};
static const struct of_device_id qusb2_phy_of_match_table[] = {
{
.compatible = "qcom,msm8996-qusb2-phy",
.data = &msm8996_phy_cfg,
}, {
.compatible = "qcom,sdm845-qusb2-phy",
.data = &sdm845_phy_cfg,
},
{ },
};
MODULE_DEVICE_TABLE(of, qusb2_phy_of_match_table);
static const struct dev_pm_ops qusb2_phy_pm_ops = {
SET_RUNTIME_PM_OPS(qusb2_phy_runtime_suspend,
qusb2_phy_runtime_resume, NULL)
};
static int qusb2_phy_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct qusb2_phy *qphy;
struct phy_provider *phy_provider;
struct phy *generic_phy;
struct resource *res;
int ret, i;
int num;
u32 value;
qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
if (!qphy)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
qphy->base = devm_ioremap_resource(dev, res);
if (IS_ERR(qphy->base))
return PTR_ERR(qphy->base);
qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb");
if (IS_ERR(qphy->cfg_ahb_clk)) {
ret = PTR_ERR(qphy->cfg_ahb_clk);
if (ret != -EPROBE_DEFER)
dev_err(dev, "failed to get cfg ahb clk, %d\n", ret);
return ret;
}
qphy->ref_clk = devm_clk_get(dev, "ref");
if (IS_ERR(qphy->ref_clk)) {
ret = PTR_ERR(qphy->ref_clk);
if (ret != -EPROBE_DEFER)
dev_err(dev, "failed to get ref clk, %d\n", ret);
return ret;
}
qphy->iface_clk = devm_clk_get(dev, "iface");
if (IS_ERR(qphy->iface_clk)) {
ret = PTR_ERR(qphy->iface_clk);
if (ret == -EPROBE_DEFER)
return ret;
qphy->iface_clk = NULL;
dev_dbg(dev, "failed to get iface clk, %d\n", ret);
}
qphy->phy_reset = devm_reset_control_get_by_index(&pdev->dev, 0);
if (IS_ERR(qphy->phy_reset)) {
dev_err(dev, "failed to get phy core reset\n");
return PTR_ERR(qphy->phy_reset);
}
num = ARRAY_SIZE(qphy->vregs);
for (i = 0; i < num; i++)
qphy->vregs[i].supply = qusb2_phy_vreg_names[i];
ret = devm_regulator_bulk_get(dev, num, qphy->vregs);
if (ret) {
dev_err(dev, "failed to get regulator supplies\n");
return ret;
}
/* Get the specific init parameters of QMP phy */
qphy->cfg = of_device_get_match_data(dev);
qphy->tcsr = syscon_regmap_lookup_by_phandle(dev->of_node,
"qcom,tcsr-syscon");
if (IS_ERR(qphy->tcsr)) {
dev_dbg(dev, "failed to lookup TCSR regmap\n");
qphy->tcsr = NULL;
}
qphy->cell = devm_nvmem_cell_get(dev, NULL);
if (IS_ERR(qphy->cell)) {
if (PTR_ERR(qphy->cell) == -EPROBE_DEFER)
return -EPROBE_DEFER;
qphy->cell = NULL;
dev_dbg(dev, "failed to lookup tune2 hstx trim value\n");
}
if (!of_property_read_u32(dev->of_node, "qcom,imp-res-offset-value",
&value)) {
qphy->imp_res_offset_value = (u8)value;
qphy->override_imp_res_offset = true;
}
if (!of_property_read_u32(dev->of_node, "qcom,hstx-trim-value",
&value)) {
qphy->hstx_trim_value = (u8)value;
qphy->override_hstx_trim = true;
}
if (!of_property_read_u32(dev->of_node, "qcom,preemphasis-level",
&value)) {
qphy->preemphasis_level = (u8)value;
qphy->override_preemphasis = true;
}
if (!of_property_read_u32(dev->of_node, "qcom,preemphasis-width",
&value)) {
qphy->preemphasis_width = (u8)value;
qphy->override_preemphasis_width = true;
}
pm_runtime_set_active(dev);
pm_runtime_enable(dev);
/*
* Prevent runtime pm from being ON by default. Users can enable
* it using power/control in sysfs.
*/
pm_runtime_forbid(dev);
generic_phy = devm_phy_create(dev, NULL, &qusb2_phy_gen_ops);
if (IS_ERR(generic_phy)) {
ret = PTR_ERR(generic_phy);
dev_err(dev, "failed to create phy, %d\n", ret);
pm_runtime_disable(dev);
return ret;
}
qphy->phy = generic_phy;
dev_set_drvdata(dev, qphy);
phy_set_drvdata(generic_phy, qphy);
phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
if (!IS_ERR(phy_provider))
dev_info(dev, "Registered Qcom-QUSB2 phy\n");
else
pm_runtime_disable(dev);
return PTR_ERR_OR_ZERO(phy_provider);
}
static struct platform_driver qusb2_phy_driver = {
.probe = qusb2_phy_probe,
.driver = {
.name = "qcom-qusb2-phy",
.pm = &qusb2_phy_pm_ops,
.of_match_table = qusb2_phy_of_match_table,
},
};
module_platform_driver(qusb2_phy_driver);
MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>");
MODULE_DESCRIPTION("Qualcomm QUSB2 PHY driver");
MODULE_LICENSE("GPL v2");
