/*
* twl4030.h - header for TWL4030 PM and audio CODEC device
*
* Copyright (C) 2005-2006 Texas Instruments, Inc.
*
* Based on tlv320aic23.c:
* Copyright (c) by Kai Svahn <kai.svahn@nokia.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#ifndef __TWL_H_
#define __TWL_H_
#include <linux/types.h>
#include <linux/input/matrix_keypad.h>
/*
* Using the twl4030 core we address registers using a pair
* { module id, relative register offset }
* which that core then maps to the relevant
* { i2c slave, absolute register address }
*
* The module IDs are meaningful only to the twl4030 core code,
* which uses them as array indices to look up the first register
* address each module uses within a given i2c slave.
*/
/* Module IDs for similar functionalities found in twl4030/twl6030 */
enum twl_module_ids {
TWL_MODULE_USB,
TWL_MODULE_PIH,
TWL_MODULE_MAIN_CHARGE,
TWL_MODULE_PM_MASTER,
TWL_MODULE_PM_RECEIVER,
TWL_MODULE_RTC,
TWL_MODULE_PWM,
TWL_MODULE_LED,
TWL_MODULE_SECURED_REG,
TWL_MODULE_LAST,
};
/* Modules only available in twl4030 series */
enum twl4030_module_ids {
TWL4030_MODULE_AUDIO_VOICE = TWL_MODULE_LAST,
TWL4030_MODULE_GPIO,
TWL4030_MODULE_INTBR,
TWL4030_MODULE_TEST,
TWL4030_MODULE_KEYPAD,
TWL4030_MODULE_MADC,
TWL4030_MODULE_INTERRUPTS,
TWL4030_MODULE_PRECHARGE,
TWL4030_MODULE_BACKUP,
TWL4030_MODULE_INT,
TWL5031_MODULE_ACCESSORY,
TWL5031_MODULE_INTERRUPTS,
TWL4030_MODULE_LAST,
};
/* Modules only available in twl6030 series */
enum twl6030_module_ids {
TWL6030_MODULE_ID0 = TWL_MODULE_LAST,
TWL6030_MODULE_ID1,
TWL6030_MODULE_ID2,
TWL6030_MODULE_GPADC,
TWL6030_MODULE_GASGAUGE,
TWL6030_MODULE_LAST,
};
/* Until the clients has been converted to use TWL_MODULE_LED */
#define TWL4030_MODULE_LED TWL_MODULE_LED
#define GPIO_INTR_OFFSET 0
#define KEYPAD_INTR_OFFSET 1
#define BCI_INTR_OFFSET 2
#define MADC_INTR_OFFSET 3
#define USB_INTR_OFFSET 4
#define CHARGERFAULT_INTR_OFFSET 5
#define BCI_PRES_INTR_OFFSET 9
#define USB_PRES_INTR_OFFSET 10
#define RTC_INTR_OFFSET 11
/*
* Offset from TWL6030_IRQ_BASE / pdata->irq_base
*/
#define PWR_INTR_OFFSET 0
#define HOTDIE_INTR_OFFSET 12
#define SMPSLDO_INTR_OFFSET 13
#define BATDETECT_INTR_OFFSET 14
#define SIMDETECT_INTR_OFFSET 15
#define MMCDETECT_INTR_OFFSET 16
#define GASGAUGE_INTR_OFFSET 17
#define USBOTG_INTR_OFFSET 4
#define CHARGER_INTR_OFFSET 2
#define RSV_INTR_OFFSET 0
/* INT register offsets */
#define REG_INT_STS_A 0x00
#define REG_INT_STS_B 0x01
#define REG_INT_STS_C 0x02
#define REG_INT_MSK_LINE_A 0x03
#define REG_INT_MSK_LINE_B 0x04
#define REG_INT_MSK_LINE_C 0x05
#define REG_INT_MSK_STS_A 0x06
#define REG_INT_MSK_STS_B 0x07
#define REG_INT_MSK_STS_C 0x08
/* MASK INT REG GROUP A */
#define TWL6030_PWR_INT_MASK 0x07
#define TWL6030_RTC_INT_MASK 0x18
#define TWL6030_HOTDIE_INT_MASK 0x20
#define TWL6030_SMPSLDOA_INT_MASK 0xC0
/* MASK INT REG GROUP B */
#define TWL6030_SMPSLDOB_INT_MASK 0x01
#define TWL6030_BATDETECT_INT_MASK 0x02
#define TWL6030_SIMDETECT_INT_MASK 0x04
#define TWL6030_MMCDETECT_INT_MASK 0x08
#define TWL6030_GPADC_INT_MASK 0x60
#define TWL6030_GASGAUGE_INT_MASK 0x80
/* MASK INT REG GROUP C */
#define TWL6030_USBOTG_INT_MASK 0x0F
#define TWL6030_CHARGER_CTRL_INT_MASK 0x10
#define TWL6030_CHARGER_FAULT_INT_MASK 0x60
#define TWL6030_MMCCTRL 0xEE
#define VMMC_AUTO_OFF (0x1 << 3)
#define SW_FC (0x1 << 2)
#define STS_MMC 0x1
#define TWL6030_CFG_INPUT_PUPD3 0xF2
#define MMC_PU (0x1 << 3)
#define MMC_PD (0x1 << 2)
#define TWL_SIL_TYPE(rev) ((rev) & 0x00FFFFFF)
#define TWL_SIL_REV(rev) ((rev) >> 24)
#define TWL_SIL_5030 0x09002F
#define TWL5030_REV_1_0 0x00
#define TWL5030_REV_1_1 0x10
#define TWL5030_REV_1_2 0x30
#define TWL4030_CLASS_ID 0x4030
#define TWL6030_CLASS_ID 0x6030
unsigned int twl_rev(void);
#define GET_TWL_REV (twl_rev())
#define TWL_CLASS_IS(class, id) \
static inline int twl_class_is_ ##class(void) \
{ \
return ((id) == (GET_TWL_REV)) ? 1 : 0; \
}
TWL_CLASS_IS(4030, TWL4030_CLASS_ID)
TWL_CLASS_IS(6030, TWL6030_CLASS_ID)
/* Set the regcache bypass for the regmap associated with the nodule */
int twl_set_regcache_bypass(u8 mod_no, bool enable);
/*
* Read and write several 8-bit registers at once.
*/
int twl_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
/*
* Read and write single 8-bit registers
*/
static inline int twl_i2c_write_u8(u8 mod_no, u8 val, u8 reg) {
return twl_i2c_write(mod_no, &val, reg, 1);
}
static inline int twl_i2c_read_u8(u8 mod_no, u8 *val, u8 reg) {
return twl_i2c_read(mod_no, val, reg, 1);
}
static inline int twl_i2c_write_u16(u8 mod_no, u16 val, u8 reg) {
val = cpu_to_le16(val);
return twl_i2c_write(mod_no, (u8*) &val, reg, 2);
}
static inline int twl_i2c_read_u16(u8 mod_no, u16 *val, u8 reg) {
int ret;
ret = twl_i2c_read(mod_no, (u8*) val, reg, 2);
*val = le16_to_cpu(*val);
return ret;
}
int twl_get_type(void);
int twl_get_version(void);
int twl_get_hfclk_rate(void);
int twl6030_interrupt_unmask(u8 bit_mask, u8 offset);
int twl6030_interrupt_mask(u8 bit_mask, u8 offset);
/* Card detect Configuration for MMC1 Controller on OMAP4 */
#ifdef CONFIG_TWL4030_CORE
int twl6030_mmc_card_detect_config(void);
#else
static inline int twl6030_mmc_card_detect_config(void)
{
pr_debug("twl6030_mmc_card_detect_config not supported\n");
return 0;
}
#endif
/* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */
#ifdef CONFIG_TWL4030_CORE
int twl6030_mmc_card_detect(struct device *dev, int slot);
#else
static inline int twl6030_mmc_card_detect(struct device *dev, int slot)
{
pr_debug("Call back twl6030_mmc_card_detect not supported\n");
return -EIO;
}
#endif
/*----------------------------------------------------------------------*/
/*
* NOTE: at up to 1024 registers, this is a big chip.
*
* Avoid putting register declarations in this file, instead of into
* a driver-private file, unless some of the registers in a block
* need to be shared with other drivers. One example is blocks that
* have Secondary IRQ Handler (SIH) registers.
*/
#define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0)
#define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1)
#define TWL4030_SIH_CTRL_COR_MASK BIT(2)
/*----------------------------------------------------------------------*/
/*
* GPIO Block Register offsets (use TWL4030_MODULE_GPIO)
*/
#define REG_GPIODATAIN1 0x0
#define REG_GPIODATAIN2 0x1
#define REG_GPIODATAIN3 0x2
#define REG_GPIODATADIR1 0x3
#define REG_GPIODATADIR2 0x4
#define REG_GPIODATADIR3 0x5
#define REG_GPIODATAOUT1 0x6
#define REG_GPIODATAOUT2 0x7
#define REG_GPIODATAOUT3 0x8
#define REG_CLEARGPIODATAOUT1 0x9
#define REG_CLEARGPIODATAOUT2 0xA
#define REG_CLEARGPIODATAOUT3 0xB
#define REG_SETGPIODATAOUT1 0xC
#define REG_SETGPIODATAOUT2 0xD
#define REG_SETGPIODATAOUT3 0xE
#define REG_GPIO_DEBEN1 0xF
#define REG_GPIO_DEBEN2 0x10
#define REG_GPIO_DEBEN3 0x11
#define REG_GPIO_CTRL 0x12
#define REG_GPIOPUPDCTR1 0x13
#define REG_GPIOPUPDCTR2 0x14
#define REG_GPIOPUPDCTR3 0x15
#define REG_GPIOPUPDCTR4 0x16
#define REG_GPIOPUPDCTR5 0x17
#define REG_GPIO_ISR1A 0x19
#define REG_GPIO_ISR2A 0x1A
#define REG_GPIO_ISR3A 0x1B
#define REG_GPIO_IMR1A 0x1C
#define REG_GPIO_IMR2A 0x1D
#define REG_GPIO_IMR3A 0x1E
#define REG_GPIO_ISR1B 0x1F
#define REG_GPIO_ISR2B 0x20
#define REG_GPIO_ISR3B 0x21
#define REG_GPIO_IMR1B 0x22
#define REG_GPIO_IMR2B 0x23
#define REG_GPIO_IMR3B 0x24
#define REG_GPIO_EDR1 0x28
#define REG_GPIO_EDR2 0x29
#define REG_GPIO_EDR3 0x2A
#define REG_GPIO_EDR4 0x2B
#define REG_GPIO_EDR5 0x2C
#define REG_GPIO_SIH_CTRL 0x2D
/* Up to 18 signals are available as GPIOs, when their
* pins are not assigned to another use (such as ULPI/USB).
*/
#define TWL4030_GPIO_MAX 18
/*----------------------------------------------------------------------*/
/*Interface Bit Register (INTBR) offsets
*(Use TWL_4030_MODULE_INTBR)
*/
#define REG_IDCODE_7_0 0x00
#define REG_IDCODE_15_8 0x01
#define REG_IDCODE_16_23 0x02
#define REG_IDCODE_31_24 0x03
#define REG_GPPUPDCTR1 0x0F
#define REG_UNLOCK_TEST_REG 0x12
/*I2C1 and I2C4(SR) SDA/SCL pull-up control bits */
#define I2C_SCL_CTRL_PU BIT(0)
#define I2C_SDA_CTRL_PU BIT(2)
#define SR_I2C_SCL_CTRL_PU BIT(4)
#define SR_I2C_SDA_CTRL_PU BIT(6)
#define TWL_EEPROM_R_UNLOCK 0x49
/*----------------------------------------------------------------------*/
/*
* Keypad register offsets (use TWL4030_MODULE_KEYPAD)
* ... SIH/interrupt only
*/
#define TWL4030_KEYPAD_KEYP_ISR1 0x11
#define TWL4030_KEYPAD_KEYP_IMR1 0x12
#define TWL4030_KEYPAD_KEYP_ISR2 0x13
#define TWL4030_KEYPAD_KEYP_IMR2 0x14
#define TWL4030_KEYPAD_KEYP_SIR 0x15 /* test register */
#define TWL4030_KEYPAD_KEYP_EDR 0x16
#define TWL4030_KEYPAD_KEYP_SIH_CTRL 0x17
/*----------------------------------------------------------------------*/
/*
* Multichannel ADC register offsets (use TWL4030_MODULE_MADC)
* ... SIH/interrupt only
*/
#define TWL4030_MADC_ISR1 0x61
#define TWL4030_MADC_IMR1 0x62
#define TWL4030_MADC_ISR2 0x63
#define TWL4030_MADC_IMR2 0x64
#define TWL4030_MADC_SIR 0x65 /* test register */
#define TWL4030_MADC_EDR 0x66
#define TWL4030_MADC_SIH_CTRL 0x67
/*----------------------------------------------------------------------*/
/*
* Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS)
*/
#define TWL4030_INTERRUPTS_BCIISR1A 0x0
#define TWL4030_INTERRUPTS_BCIISR2A 0x1
#define TWL4030_INTERRUPTS_BCIIMR1A 0x2
#define TWL4030_INTERRUPTS_BCIIMR2A 0x3
#define TWL4030_INTERRUPTS_BCIISR1B 0x4
#define TWL4030_INTERRUPTS_BCIISR2B 0x5
#define TWL4030_INTERRUPTS_BCIIMR1B 0x6
#define TWL4030_INTERRUPTS_BCIIMR2B 0x7
#define TWL4030_INTERRUPTS_BCISIR1 0x8 /* test register */
#define TWL4030_INTERRUPTS_BCISIR2 0x9 /* test register */
#define TWL4030_INTERRUPTS_BCIEDR1 0xa
#define TWL4030_INTERRUPTS_BCIEDR2 0xb
#define TWL4030_INTERRUPTS_BCIEDR3 0xc
#define TWL4030_INTERRUPTS_BCISIHCTRL 0xd
/*----------------------------------------------------------------------*/
/*
* Power Interrupt block register offsets (use TWL4030_MODULE_INT)
*/
#define TWL4030_INT_PWR_ISR1 0x0
#define TWL4030_INT_PWR_IMR1 0x1
#define TWL4030_INT_PWR_ISR2 0x2
#define TWL4030_INT_PWR_IMR2 0x3
#define TWL4030_INT_PWR_SIR 0x4 /* test register */
#define TWL4030_INT_PWR_EDR1 0x5
#define TWL4030_INT_PWR_EDR2 0x6
#define TWL4030_INT_PWR_SIH_CTRL 0x7
/*----------------------------------------------------------------------*/
/*
* Accessory Interrupts
*/
#define TWL5031_ACIIMR_LSB 0x05
#define TWL5031_ACIIMR_MSB 0x06
#define TWL5031_ACIIDR_LSB 0x07
#define TWL5031_ACIIDR_MSB 0x08
#define TWL5031_ACCISR1 0x0F
#define TWL5031_ACCIMR1 0x10
#define TWL5031_ACCISR2 0x11
#define TWL5031_ACCIMR2 0x12
#define TWL5031_ACCSIR 0x13
#define TWL5031_ACCEDR1 0x14
#define TWL5031_ACCSIHCTRL 0x15
/*----------------------------------------------------------------------*/
/*
* Battery Charger Controller
*/
#define TWL5031_INTERRUPTS_BCIISR1 0x0
#define TWL5031_INTERRUPTS_BCIIMR1 0x1
#define TWL5031_INTERRUPTS_BCIISR2 0x2
#define TWL5031_INTERRUPTS_BCIIMR2 0x3
#define TWL5031_INTERRUPTS_BCISIR 0x4
#define TWL5031_INTERRUPTS_BCIEDR1 0x5
#define TWL5031_INTERRUPTS_BCIEDR2 0x6
#define TWL5031_INTERRUPTS_BCISIHCTRL 0x7
/*----------------------------------------------------------------------*/
/*
* PM Master module register offsets (use TWL4030_MODULE_PM_MASTER)
*/
#define TWL4030_PM_MASTER_CFG_P1_TRANSITION 0x00
#define TWL4030_PM_MASTER_CFG_P2_TRANSITION 0x01
#define TWL4030_PM_MASTER_CFG_P3_TRANSITION 0x02
#define TWL4030_PM_MASTER_CFG_P123_TRANSITION 0x03
#define TWL4030_PM_MASTER_STS_BOOT 0x04
#define TWL4030_PM_MASTER_CFG_BOOT 0x05
#define TWL4030_PM_MASTER_SHUNDAN 0x06
#define TWL4030_PM_MASTER_BOOT_BCI 0x07
#define TWL4030_PM_MASTER_CFG_PWRANA1 0x08
#define TWL4030_PM_MASTER_CFG_PWRANA2 0x09
#define TWL4030_PM_MASTER_BACKUP_MISC_STS 0x0b
#define TWL4030_PM_MASTER_BACKUP_MISC_CFG 0x0c
#define TWL4030_PM_MASTER_BACKUP_MISC_TST 0x0d
#define TWL4030_PM_MASTER_PROTECT_KEY 0x0e
#define TWL4030_PM_MASTER_STS_HW_CONDITIONS 0x0f
#define TWL4030_PM_MASTER_P1_SW_EVENTS 0x10
#define TWL4030_PM_MASTER_P2_SW_EVENTS 0x11
#define TWL4030_PM_MASTER_P3_SW_EVENTS 0x12
#define TWL4030_PM_MASTER_STS_P123_STATE 0x13
#define TWL4030_PM_MASTER_PB_CFG 0x14
#define TWL4030_PM_MASTER_PB_WORD_MSB 0x15
#define TWL4030_PM_MASTER_PB_WORD_LSB 0x16
#define TWL4030_PM_MASTER_SEQ_ADD_W2P 0x1c
#define TWL4030_PM_MASTER_SEQ_ADD_P2A 0x1d
#define TWL4030_PM_MASTER_SEQ_ADD_A2W 0x1e
#define TWL4030_PM_MASTER_SEQ_ADD_A2S 0x1f
#define TWL4030_PM_MASTER_SEQ_ADD_S2A12 0x20
#define TWL4030_PM_MASTER_SEQ_ADD_S2A3 0x21
#define TWL4030_PM_MASTER_SEQ_ADD_WARM 0x22
#define TWL4030_PM_MASTER_MEMORY_ADDRESS 0x23
#define TWL4030_PM_MASTER_MEMORY_DATA 0x24
#define TWL4030_PM_MASTER_KEY_CFG1 0xc0
#define TWL4030_PM_MASTER_KEY_CFG2 0x0c
#define TWL4030_PM_MASTER_KEY_TST1 0xe0
#define TWL4030_PM_MASTER_KEY_TST2 0x0e
#define TWL4030_PM_MASTER_GLOBAL_TST 0xb6
/*----------------------------------------------------------------------*/
/* Power bus message definitions */
/* The TWL4030/5030 splits its power-management resources (the various
* regulators, clock and reset lines) into 3 processor groups - P1, P2 and
* P3. These groups can then be configured to transition between sleep, wait-on
* and active states by sending messages to the power bus. See Section 5.4.2
* Power Resources of TWL4030 TRM
*/
/* Processor groups */
#define DEV_GRP_NULL 0x0
#define DEV_GRP_P1 0x1 /* P1: all OMAP devices */
#define DEV_GRP_P2 0x2 /* P2: all Modem devices */
#define DEV_GRP_P3 0x4 /* P3: all peripheral devices */
/* Resource groups */
#define RES_GRP_RES 0x0 /* Reserved */
#define RES_GRP_PP 0x1 /* Power providers */
#define RES_GRP_RC 0x2 /* Reset and control */
#define RES_GRP_PP_RC 0x3
#define RES_GRP_PR 0x4 /* Power references */
#define RES_GRP_PP_PR 0x5
#define RES_GRP_RC_PR 0x6
#define RES_GRP_ALL 0x7 /* All resource groups */
#define RES_TYPE2_R0 0x0
#define RES_TYPE2_R1 0x1
#define RES_TYPE2_R2 0x2
#define RES_TYPE_R0 0x0
#define RES_TYPE_ALL 0x7
/* Resource states */
#define RES_STATE_WRST 0xF
#define RES_STATE_ACTIVE 0xE
#define RES_STATE_SLEEP 0x8
#define RES_STATE_OFF 0x0
/* Power resources */
/* Power providers */
#define RES_VAUX1 1
#define RES_VAUX2 2
#define RES_VAUX3 3
#define RES_VAUX4 4
#define RES_VMMC1 5
#define RES_VMMC2 6
#define RES_VPLL1 7
#define RES_VPLL2 8
#define RES_VSIM 9
#define RES_VDAC 10
#define RES_VINTANA1 11
#define RES_VINTANA2 12
#define RES_VINTDIG 13
#define RES_VIO 14
#define RES_VDD1 15
#define RES_VDD2 16
#define RES_VUSB_1V5 17
#define RES_VUSB_1V8 18
#define RES_VUSB_3V1 19
#define RES_VUSBCP 20
#define RES_REGEN 21
/* Reset and control */
#define RES_NRES_PWRON 22
#define RES_CLKEN 23
#define RES_SYSEN 24
#define RES_HFCLKOUT 25
#define RES_32KCLKOUT 26
#define RES_RESET 27
/* Power Reference */
#define RES_MAIN_REF 28
#define TOTAL_RESOURCES 28
/*
* Power Bus Message Format ... these can be sent individually by Linux,
* but are usually part of downloaded scripts that are run when various
* power events are triggered.
*
* Broadcast Message (16 Bits):
* DEV_GRP[15:13] MT[12] RES_GRP[11:9] RES_TYPE2[8:7] RES_TYPE[6:4]
* RES_STATE[3:0]
*
* Singular Message (16 Bits):
* DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0]
*/
#define MSG_BROADCAST(devgrp, grp, type, type2, state) \
( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \
| (type) << 4 | (state))
#define MSG_SINGULAR(devgrp, id, state) \
((devgrp) << 13 | 0 << 12 | (id) << 4 | (state))
#define MSG_BROADCAST_ALL(devgrp, state) \
((devgrp) << 5 | (state))
#define MSG_BROADCAST_REF MSG_BROADCAST_ALL
#define MSG_BROADCAST_PROV MSG_BROADCAST_ALL
#define MSG_BROADCAST__CLK_RST MSG_BROADCAST_ALL
/*----------------------------------------------------------------------*/
struct twl4030_clock_init_data {
bool ck32k_lowpwr_enable;
};
struct twl4030_bci_platform_data {
int *battery_tmp_tbl;
unsigned int tblsize;
int bb_uvolt; /* voltage to charge backup battery */
int bb_uamp; /* current for backup battery charging */
};
/* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */
struct twl4030_gpio_platform_data {
/* package the two LED signals as output-only GPIOs? */
bool use_leds;
/* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */
u8 mmc_cd;
/* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */
u32 debounce;
/* For gpio-N, bit (1 << N) in "pullups" is set if that pullup
* should be enabled. Else, if that bit is set in "pulldowns",
* that pulldown is enabled. Don't waste power by letting any
* digital inputs float...
*/
u32 pullups;
u32 pulldowns;
int (*setup)(struct device *dev,
unsigned gpio, unsigned ngpio);
int (*teardown)(struct device *dev,
unsigned gpio, unsigned ngpio);
};
struct twl4030_madc_platform_data {
int irq_line;
};
/* Boards have unique mappings of {row, col} --> keycode.
* Column and row are 8 bits each, but range only from 0..7.
* a PERSISTENT_KEY is "always on" and never reported.
*/
#define PERSISTENT_KEY(r, c) KEY((r), (c), KEY_RESERVED)
struct twl4030_keypad_data {
const struct matrix_keymap_data *keymap_data;
unsigned rows;
unsigned cols;
bool rep;
};
enum twl4030_usb_mode {
T2_USB_MODE_ULPI = 1,
T2_USB_MODE_CEA2011_3PIN = 2,
};
struct twl4030_usb_data {
enum twl4030_usb_mode usb_mode;
unsigned long features;
int (*phy_init)(struct device *dev);
int (*phy_exit)(struct device *dev);
/* Power on/off the PHY */
int (*phy_power)(struct device *dev, int iD, int on);
/* enable/disable phy clocks */
int (*phy_set_clock)(struct device *dev, int on);
/* suspend/resume of phy */
int (*phy_suspend)(struct device *dev, int suspend);
};
struct twl4030_ins {
u16 pmb_message;
u8 delay;
};
struct twl4030_script {
struct twl4030_ins *script;
unsigned size;
u8 flags;
#define TWL4030_WRST_SCRIPT (1<<0)
#define TWL4030_WAKEUP12_SCRIPT (1<<1)
#define TWL4030_WAKEUP3_SCRIPT (1<<2)
#define TWL4030_SLEEP_SCRIPT (1<<3)
};
struct twl4030_resconfig {
u8 resource;
u8 devgroup; /* Processor group that Power resource belongs to */
u8 type; /* Power resource addressed, 6 / broadcast message */
u8 type2; /* Power resource addressed, 3 / broadcast message */
u8 remap_off; /* off state remapping */
u8 remap_sleep; /* sleep state remapping */
};
struct twl4030_power_data {
struct twl4030_script **scripts;
unsigned num;
struct twl4030_resconfig *resource_config;
struct twl4030_resconfig *board_config;
#define TWL4030_RESCONFIG_UNDEF ((u8)-1)
bool use_poweroff; /* Board is wired for TWL poweroff */
bool ac_charger_quirk; /* Disable AC charger on board */
};
extern int twl4030_remove_script(u8 flags);
extern void twl4030_power_off(void);
struct twl4030_codec_data {
unsigned int digimic_delay; /* in ms */
unsigned int ramp_delay_value;
unsigned int offset_cncl_path;
unsigned int hs_extmute:1;
int hs_extmute_gpio;
};
struct twl4030_vibra_data {
unsigned int coexist;
};
struct twl4030_audio_data {
unsigned int audio_mclk;
struct twl4030_codec_data *codec;
struct twl4030_vibra_data *vibra;
/* twl6040 */
int audpwron_gpio; /* audio power-on gpio */
int naudint_irq; /* audio interrupt */
unsigned int irq_base;
};
struct twl4030_platform_data {
struct twl4030_clock_init_data *clock;
struct twl4030_bci_platform_data *bci;
struct twl4030_gpio_platform_data *gpio;
struct twl4030_madc_platform_data *madc;
struct twl4030_keypad_data *keypad;
struct twl4030_usb_data *usb;
struct twl4030_power_data *power;
struct twl4030_audio_data *audio;
/* Common LDO regulators for TWL4030/TWL6030 */
struct regulator_init_data *vdac;
struct regulator_init_data *vaux1;
struct regulator_init_data *vaux2;
struct regulator_init_data *vaux3;
struct regulator_init_data *vdd1;
struct regulator_init_data *vdd2;
struct regulator_init_data *vdd3;
/* TWL4030 LDO regulators */
struct regulator_init_data *vpll1;
struct regulator_init_data *vpll2;
struct regulator_init_data *vmmc1;
struct regulator_init_data *vmmc2;
struct regulator_init_data *vsim;
struct regulator_init_data *vaux4;
struct regulator_init_data *vio;
struct regulator_init_data *vintana1;
struct regulator_init_data *vintana2;
struct regulator_init_data *vintdig;
/* TWL6030 LDO regulators */
struct regulator_init_data *vmmc;
struct regulator_init_data *vpp;
struct regulator_init_data *vusim;
struct regulator_init_data *vana;
struct regulator_init_data *vcxio;
struct regulator_init_data *vusb;
struct regulator_init_data *clk32kg;
struct regulator_init_data *v1v8;
struct regulator_init_data *v2v1;
/* TWL6032 LDO regulators */
struct regulator_init_data *ldo1;
struct regulator_init_data *ldo2;
struct regulator_init_data *ldo3;
struct regulator_init_data *ldo4;
struct regulator_init_data *ldo5;
struct regulator_init_data *ldo6;
struct regulator_init_data *ldo7;
struct regulator_init_data *ldoln;
struct regulator_init_data *ldousb;
/* TWL6032 DCDC regulators */
struct regulator_init_data *smps3;
struct regulator_init_data *smps4;
struct regulator_init_data *vio6025;
};
struct twl_regulator_driver_data {
int (*set_voltage)(void *data, int target_uV);
int (*get_voltage)(void *data);
void *data;
unsigned long features;
};
/* chip-specific feature flags, for twl_regulator_driver_data.features */
#define TWL4030_VAUX2 BIT(0) /* pre-5030 voltage ranges */
#define TPS_SUBSET BIT(1) /* tps659[23]0 have fewer LDOs */
#define TWL5031 BIT(2) /* twl5031 has different registers */
#define TWL6030_CLASS BIT(3) /* TWL6030 class */
#define TWL6032_SUBCLASS BIT(4) /* TWL6032 has changed registers */
#define TWL4030_ALLOW_UNSUPPORTED BIT(5) /* Some voltages are possible
* but not officially supported.
* This flag is necessary to
* enable them.
*/
/*----------------------------------------------------------------------*/
int twl4030_sih_setup(struct device *dev, int module, int irq_base);
/* Offsets to Power Registers */
#define TWL4030_VDAC_DEV_GRP 0x3B
#define TWL4030_VDAC_DEDICATED 0x3E
#define TWL4030_VAUX1_DEV_GRP 0x17
#define TWL4030_VAUX1_DEDICATED 0x1A
#define TWL4030_VAUX2_DEV_GRP 0x1B
#define TWL4030_VAUX2_DEDICATED 0x1E
#define TWL4030_VAUX3_DEV_GRP 0x1F
#define TWL4030_VAUX3_DEDICATED 0x22
static inline int twl4030charger_usb_en(int enable) { return 0; }
/*----------------------------------------------------------------------*/
/* Linux-specific regulator identifiers ... for now, we only support
* the LDOs, and leave the three buck converters alone. VDD1 and VDD2
* need to tie into hardware based voltage scaling (cpufreq etc), while
* VIO is generally fixed.
*/
/* TWL4030 SMPS/LDO's */
/* EXTERNAL dc-to-dc buck converters */
#define TWL4030_REG_VDD1 0
#define TWL4030_REG_VDD2 1
#define TWL4030_REG_VIO 2
/* EXTERNAL LDOs */
#define TWL4030_REG_VDAC 3
#define TWL4030_REG_VPLL1 4
#define TWL4030_REG_VPLL2 5 /* not on all chips */
#define TWL4030_REG_VMMC1 6
#define TWL4030_REG_VMMC2 7 /* not on all chips */
#define TWL4030_REG_VSIM 8 /* not on all chips */
#define TWL4030_REG_VAUX1 9 /* not on all chips */
#define TWL4030_REG_VAUX2_4030 10 /* (twl4030-specific) */
#define TWL4030_REG_VAUX2 11 /* (twl5030 and newer) */
#define TWL4030_REG_VAUX3 12 /* not on all chips */
#define TWL4030_REG_VAUX4 13 /* not on all chips */
/* INTERNAL LDOs */
#define TWL4030_REG_VINTANA1 14
#define TWL4030_REG_VINTANA2 15
#define TWL4030_REG_VINTDIG 16
#define TWL4030_REG_VUSB1V5 17
#define TWL4030_REG_VUSB1V8 18
#define TWL4030_REG_VUSB3V1 19
/* TWL6030 SMPS/LDO's */
/* EXTERNAL dc-to-dc buck convertor controllable via SR */
#define TWL6030_REG_VDD1 30
#define TWL6030_REG_VDD2 31
#define TWL6030_REG_VDD3 32
/* Non SR compliant dc-to-dc buck convertors */
#define TWL6030_REG_VMEM 33
#define TWL6030_REG_V2V1 34
#define TWL6030_REG_V1V29 35
#define TWL6030_REG_V1V8 36
/* EXTERNAL LDOs */
#define TWL6030_REG_VAUX1_6030 37
#define TWL6030_REG_VAUX2_6030 38
#define TWL6030_REG_VAUX3_6030 39
#define TWL6030_REG_VMMC 40
#define TWL6030_REG_VPP 41
#define TWL6030_REG_VUSIM 42
#define TWL6030_REG_VANA 43
#define TWL6030_REG_VCXIO 44
#define TWL6030_REG_VDAC 45
#define TWL6030_REG_VUSB 46
/* INTERNAL LDOs */
#define TWL6030_REG_VRTC 47
#define TWL6030_REG_CLK32KG 48
/* LDOs on 6025 have different names */
#define TWL6032_REG_LDO2 49
#define TWL6032_REG_LDO4 50
#define TWL6032_REG_LDO3 51
#define TWL6032_REG_LDO5 52
#define TWL6032_REG_LDO1 53
#define TWL6032_REG_LDO7 54
#define TWL6032_REG_LDO6 55
#define TWL6032_REG_LDOLN 56
#define TWL6032_REG_LDOUSB 57
/* 6025 DCDC supplies */
#define TWL6032_REG_SMPS3 58
#define TWL6032_REG_SMPS4 59
#define TWL6032_REG_VIO 60
#endif /* End of __TWL4030_H */
