/*
* Copyright (C) ST-Ericsson SA 2007-2010
* Author: Per Forlin <per.forlin@stericsson.com> for ST-Ericsson
* Author: Jonas Aaberg <jonas.aberg@stericsson.com> for ST-Ericsson
* License terms: GNU General Public License (GPL) version 2
*/
#ifndef STE_DMA40_H
#define STE_DMA40_H
#include <linux/dmaengine.h>
#include <linux/scatterlist.h>
#include <linux/workqueue.h>
#include <linux/interrupt.h>
/*
* Maxium size for a single dma descriptor
* Size is limited to 16 bits.
* Size is in the units of addr-widths (1,2,4,8 bytes)
* Larger transfers will be split up to multiple linked desc
*/
#define STEDMA40_MAX_SEG_SIZE 0xFFFF
/* dev types for memcpy */
#define STEDMA40_DEV_DST_MEMORY (-1)
#define STEDMA40_DEV_SRC_MEMORY (-1)
enum stedma40_mode {
STEDMA40_MODE_LOGICAL = 0,
STEDMA40_MODE_PHYSICAL,
STEDMA40_MODE_OPERATION,
};
enum stedma40_mode_opt {
STEDMA40_PCHAN_BASIC_MODE = 0,
STEDMA40_LCHAN_SRC_LOG_DST_LOG = 0,
STEDMA40_PCHAN_MODULO_MODE,
STEDMA40_PCHAN_DOUBLE_DST_MODE,
STEDMA40_LCHAN_SRC_PHY_DST_LOG,
STEDMA40_LCHAN_SRC_LOG_DST_PHY,
};
#define STEDMA40_ESIZE_8_BIT 0x0
#define STEDMA40_ESIZE_16_BIT 0x1
#define STEDMA40_ESIZE_32_BIT 0x2
#define STEDMA40_ESIZE_64_BIT 0x3
/* The value 4 indicates that PEN-reg shall be set to 0 */
#define STEDMA40_PSIZE_PHY_1 0x4
#define STEDMA40_PSIZE_PHY_2 0x0
#define STEDMA40_PSIZE_PHY_4 0x1
#define STEDMA40_PSIZE_PHY_8 0x2
#define STEDMA40_PSIZE_PHY_16 0x3
/*
* The number of elements differ in logical and
* physical mode
*/
#define STEDMA40_PSIZE_LOG_1 STEDMA40_PSIZE_PHY_2
#define STEDMA40_PSIZE_LOG_4 STEDMA40_PSIZE_PHY_4
#define STEDMA40_PSIZE_LOG_8 STEDMA40_PSIZE_PHY_8
#define STEDMA40_PSIZE_LOG_16 STEDMA40_PSIZE_PHY_16
/* Maximum number of possible physical channels */
#define STEDMA40_MAX_PHYS 32
enum stedma40_flow_ctrl {
STEDMA40_NO_FLOW_CTRL,
STEDMA40_FLOW_CTRL,
};
/**
* struct stedma40_half_channel_info - dst/src channel configuration
*
* @big_endian: true if the src/dst should be read as big endian
* @data_width: Data width of the src/dst hardware
* @p_size: Burst size
* @flow_ctrl: Flow control on/off.
*/
struct stedma40_half_channel_info {
bool big_endian;
enum dma_slave_buswidth data_width;
int psize;
enum stedma40_flow_ctrl flow_ctrl;
};
/**
* struct stedma40_chan_cfg - Structure to be filled by client drivers.
*
* @dir: MEM 2 MEM, PERIPH 2 MEM , MEM 2 PERIPH, PERIPH 2 PERIPH
* @high_priority: true if high-priority
* @realtime: true if realtime mode is to be enabled. Only available on DMA40
* version 3+, i.e DB8500v2+
* @mode: channel mode: physical, logical, or operation
* @mode_opt: options for the chosen channel mode
* @dev_type: src/dst device type (driver uses dir to figure out which)
* @src_info: Parameters for dst half channel
* @dst_info: Parameters for dst half channel
* @use_fixed_channel: if true, use physical channel specified by phy_channel
* @phy_channel: physical channel to use, only if use_fixed_channel is true
*
* This structure has to be filled by the client drivers.
* It is recommended to do all dma configurations for clients in the machine.
*
*/
struct stedma40_chan_cfg {
enum dma_transfer_direction dir;
bool high_priority;
bool realtime;
enum stedma40_mode mode;
enum stedma40_mode_opt mode_opt;
int dev_type;
struct stedma40_half_channel_info src_info;
struct stedma40_half_channel_info dst_info;
bool use_fixed_channel;
int phy_channel;
};
/**
* struct stedma40_platform_data - Configuration struct for the dma device.
*
* @dev_tx: mapping between destination event line and io address
* @dev_rx: mapping between source event line and io address
* @disabled_channels: A vector, ending with -1, that marks physical channels
* that are for different reasons not available for the driver.
* @soft_lli_chans: A vector, that marks physical channels will use LLI by SW
* which avoids HW bug that exists in some versions of the controller.
* SoftLLI introduces relink overhead that could impact performace for
* certain use cases.
* @num_of_soft_lli_chans: The number of channels that needs to be configured
* to use SoftLLI.
* @use_esram_lcla: flag for mapping the lcla into esram region
* @num_of_memcpy_chans: The number of channels reserved for memcpy.
* @num_of_phy_chans: The number of physical channels implemented in HW.
* 0 means reading the number of channels from DMA HW but this is only valid
* for 'multiple of 4' channels, like 8.
*/
struct stedma40_platform_data {
int disabled_channels[STEDMA40_MAX_PHYS];
int *soft_lli_chans;
int num_of_soft_lli_chans;
bool use_esram_lcla;
int num_of_memcpy_chans;
int num_of_phy_chans;
};
#ifdef CONFIG_STE_DMA40
/**
* stedma40_filter() - Provides stedma40_chan_cfg to the
* ste_dma40 dma driver via the dmaengine framework.
* does some checking of what's provided.
*
* Never directly called by client. It used by dmaengine.
* @chan: dmaengine handle.
* @data: Must be of type: struct stedma40_chan_cfg and is
* the configuration of the framework.
*
*
*/
bool stedma40_filter(struct dma_chan *chan, void *data);
/**
* stedma40_slave_mem() - Transfers a raw data buffer to or from a slave
* (=device)
*
* @chan: dmaengine handle
* @addr: source or destination physicall address.
* @size: bytes to transfer
* @direction: direction of transfer
* @flags: is actually enum dma_ctrl_flags. See dmaengine.h
*/
static inline struct
dma_async_tx_descriptor *stedma40_slave_mem(struct dma_chan *chan,
dma_addr_t addr,
unsigned int size,
enum dma_transfer_direction direction,
unsigned long flags)
{
struct scatterlist sg;
sg_init_table(&sg, 1);
sg.dma_address = addr;
sg.length = size;
return dmaengine_prep_slave_sg(chan, &sg, 1, direction, flags);
}
#else
static inline bool stedma40_filter(struct dma_chan *chan, void *data)
{
return false;
}
static inline struct
dma_async_tx_descriptor *stedma40_slave_mem(struct dma_chan *chan,
dma_addr_t addr,
unsigned int size,
enum dma_transfer_direction direction,
unsigned long flags)
{
return NULL;
}
#endif
#endif
