Merge tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd

Pull MTD updates from Brian Norris:
 - refactor m25p80.c driver for use as a general SPI NOR framework for
   other drivers which may speak to SPI NOR flash without providing full
   SPI support (i.e., not part of drivers/spi/)
 - new Freescale QuadSPI driver (utilizing new SPI NOR framework)
 - updates for the STMicro "FSM" SPI NOR driver
 - fix sync/flush behavior on mtd_blkdevs
 - fixup subpage write support on a few NAND drivers
 - correct the MTD OOB test for odd-sized OOB areas
 - add BCH-16 support for OMAP NAND
 - fix warnings and trivial refactoring
 - utilize new ECC DT bindings in pxa3xx NAND driver
 - new LPDDR NVM driver
 - address a few assorted bugs caught by Coverity
 - add new imx6sx support for GPMI NAND
 - use a bounce buffer for NAND when non-DMA-able buffers are used

* tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd: (77 commits)
  mtd: gpmi: add gpmi support for imx6sx
  mtd: maps: remove check for CONFIG_MTD_SUPERH_RESERVE
  mtd: bf5xx_nand: use the managed version of kzalloc
  mtd: pxa3xx_nand: make the driver work on big-endian systems
  mtd: nand: omap: fix omap_calculate_ecc_bch() for-loop error
  mtd: nand: r852: correct write_buf loop bounds
  mtd: nand_bbt: handle error case for nand_create_badblock_pattern()
  mtd: nand_bbt: remove unused variable
  mtd: maps: sc520cdp: fix warnings
  mtd: slram: fix unused variable warning
  mtd: pfow: remove unused variable
  mtd: lpddr: fix Kconfig dependency, for I/O accessors
  mtd: nand: pxa3xx: Add supported ECC strength and step size to the DT binding
  mtd: nand: pxa3xx: Use ECC strength and step size devicetree binding
  mtd: nand: pxa3xx: Clean pxa_ecc_init() error handling
  mtd: nand: Warn the user if the selected ECC strength is too weak
  mtd: nand: omap: Documentation: How to select correct ECC scheme for your device ?
  mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
  mtd: nand: omap: add support for BCH16_ECC - ELM driver updates
  mtd: nand: omap: add support for BCH16_ECC - GPMC driver updates
  ...

1 files changed, 35 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
new file mode 100644
index 000000000000..823d13412195
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
@@ -0,0 +1,35 @@
+* Freescale Quad Serial Peripheral Interface(QuadSPI)
+
+Required properties:
+  - compatible : Should be "fsl,vf610-qspi"
+  - reg : the first contains the register location and length,
+          the second contains the memory mapping address and length
+  - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
+  - interrupts : Should contain the interrupt for the device
+  - clocks : The clocks needed by the QuadSPI controller
+  - clock-names : the name of the clocks
+
+Optional properties:
+  - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B.
+                              Each bus can be connected with two NOR flashes.
+			      Most of the time, each bus only has one NOR flash
+			      connected, this is the default case.
+			      But if there are two NOR flashes connected to the
+			      bus, you should enable this property.
+			      (Please check the board's schematic.)
+
+Example:
+
+qspi0: quadspi@40044000 {
+	compatible = "fsl,vf610-qspi";
+	reg = <0x40044000 0x1000>, <0x20000000 0x10000000>;
+	reg-names = "QuadSPI", "QuadSPI-memory";
+	interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&clks VF610_CLK_QSPI0_EN>,
+		<&clks VF610_CLK_QSPI0>;
+	clock-names = "qspi_en", "qspi";
+
+	flash0: s25fl128s@0 {
+		....
+	};
+};