Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing

Felipe writes:

usb: changes for v4.17 merge window

Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:

Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.

Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.

We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.

We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).

Apart from these, we have our regular set of non-critical fixes all
over the place.

2 files changed, 58 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt b/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt
new file mode 100644
index 000000000000..9a8b631904fd
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt
@@ -0,0 +1,42 @@
+Amlogic Meson GX DWC3 USB SoC controller
+
+Required properties:
+- compatible:	depending on the SoC this should contain one of:
+			* amlogic,meson-axg-dwc3
+			* amlogic,meson-gxl-dwc3
+- clocks:	a handle for the "USB general" clock
+- clock-names:	must be "usb_general"
+- resets:	a handle for the shared "USB OTG" reset line
+- reset-names:	must be "usb_otg"
+
+Required child node:
+A child node must exist to represent the core DWC3 IP block. The name of
+the node is not important. The content of the node is defined in dwc3.txt.
+
+PHY documentation is provided in the following places:
+- Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt
+- Documentation/devicetree/bindings/phy/meson-gxl-usb3-phy.txt
+
+Example device nodes:
+		usb0: usb@ff500000 {
+			compatible = "amlogic,meson-axg-dwc3";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&clkc CLKID_USB>;
+			clock-names = "usb_general";
+			resets = <&reset RESET_USB_OTG>;
+			reset-names = "usb_otg";
+
+			dwc3: dwc3@ff500000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xff500000 0x0 0x100000>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				maximum-speed = "high-speed";
+				snps,dis_u2_susphy_quirk;
+				phys = <&usb3_phy>, <&usb2_phy0>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
index 44e8bab159ad..0dbd3083e7dd 100644
--- a/Documentation/devicetree/bindings/usb/dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/dwc3.txt
@@ -57,6 +57,22 @@ Optional properties:
  - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
 	register for post-silicon frame length adjustment when the
 	fladj_30mhz_sdbnd signal is invalid or incorrect.
+ - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode
+			only. Set this and rx-max-burst-prd to a valid,
+			non-zero value 1-16 (DWC_usb31 programming guide
+			section 1.2.4) to enable periodic ESS RX threshold.
+ - snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set
+			this and rx-thr-num-pkt-prd to a valid, non-zero value
+			1-16 (DWC_usb31 programming guide section 1.2.4) to
+			enable periodic ESS RX threshold.
+ - snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode
+			only. Set this and tx-max-burst-prd to a valid,
+			non-zero value 1-16 (DWC_usb31 programming guide
+			section 1.2.3) to enable periodic ESS TX threshold.
+ - snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set
+			this and tx-thr-num-pkt-prd to a valid, non-zero value
+			1-16 (DWC_usb31 programming guide section 1.2.3) to
+			enable periodic ESS TX threshold.
 
  - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.