Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next

Pull part one of ARM SoC updates from Olof Johansson:
 "A quite large set of SoC updates this cycle.  In no particular order:

   - Multi-cluster power management for Samsung Exynos, adding support
     for big.LITTLE CPU switching on EXYNOS5

   - SMP support for Marvell Armada 375 and 38x

   - SMP rework on Allwinner A31

   - Xilinx Zynq support for SOC_BUS, big endian

   - Marvell orion5x platform cleanup, modernizing the implementation
     and moving to DT.

   - _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
     that their platform can be enabled in the same kernel binary as
     most of the other v7 platforms in the tree.  \o/

     The work isn't quite complete, there's some driver fixes still
     needed, but the basics now work.

  New SoC support added:

   - Freescale i.MX6SX

   - LSI Axxia AXM55xx SoCs

   - Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800

   - STi STIH407

  plus a large set of various smaller updates for different platforms.
  I'm probably missing some important one here"

* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
  ARM: exynos: don't run exynos4 l2x0 setup on other platforms
  ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
  ARM: EXYNOS: mcpm rename the power_down_finish
  ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
  ARM: EXYNOS: Enable multi-platform build support
  ARM: EXYNOS: Consolidate Kconfig entries
  ARM: EXYNOS: Add support for EXYNOS5410 SoC
  ARM: EXYNOS: Support secondary CPU boot of Exynos3250
  ARM: EXYNOS: Add Exynos3250 SoC ID
  ARM: EXYNOS: Add 5800 SoC support
  ARM: EXYNOS: initial board support for exynos5260 SoC
  clk: exynos5410: register clocks using common clock framework
  ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
  ARM: sunxi: allow building without reset controller
  Documentation: devicetree: arm: sort enable-method entries
  ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
  clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
  ARM: dts: axxia: Add reset controller
  power: reset: Add Axxia system reset driver
  ARM: axxia: Adding defconfig for AXM55xx
  ...

1 files changed, 54 insertions, 50 deletions

diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 4678870f8ee8..8f90595069a1 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -317,6 +317,13 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on i.MX6SL.
 
+	config DEBUG_IMX6SX_UART
+		bool "i.MX6SX Debug UART"
+		depends on SOC_IMX6SX
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on i.MX6SX.
+
 	config DEBUG_KEYSTONE_UART0
 		bool "Kernel low-level debugging on KEYSTONE2 using UART0"
 		depends on ARCH_KEYSTONE
@@ -349,56 +356,40 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on MMP UART3.
 
-	config DEBUG_MSM_UART1
-		bool "Kernel low-level debugging messages via MSM UART1"
-		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
-		select DEBUG_MSM_UART
+	config DEBUG_MSM_UART
+		bool "Kernel low-level debugging messages via MSM UART"
+		depends on ARCH_MSM
 		help
 		  Say Y here if you want the debug print routines to direct
-		  their output to the first serial port on MSM devices.
+		  their output to the serial port on MSM devices.
 
-	config DEBUG_MSM_UART2
-		bool "Kernel low-level debugging messages via MSM UART2"
-		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
-		select DEBUG_MSM_UART
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to the second serial port on MSM devices.
+		  ARCH                DEBUG_UART_PHYS   DEBUG_UART_BASE   #
+		  MSM7X00A, QSD8X50   0xa9a00000        0xe1000000        UART1
+		  MSM7X00A, QSD8X50   0xa9b00000        0xe1000000        UART2
+		  MSM7X00A, QSD8X50   0xa9c00000        0xe1000000        UART3
 
-	config DEBUG_MSM_UART3
-		bool "Kernel low-level debugging messages via MSM UART3"
-		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
-		select DEBUG_MSM_UART
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to the third serial port on MSM devices.
+		  MSM7X30             0xaca00000        0xe1000000        UART1
+		  MSM7X30             0xacb00000        0xe1000000        UART2
+		  MSM7X30             0xacc00000        0xe1000000        UART3
 
-	config DEBUG_MSM8660_UART
-		bool "Kernel low-level debugging messages via MSM 8660 UART"
-		depends on ARCH_MSM8X60
-		select MSM_HAS_DEBUG_UART_HS
-		select DEBUG_MSM_UART
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to the serial port on MSM 8660 devices.
+		  Please adjust DEBUG_UART_PHYS and DEBUG_UART_BASE configuration
+		  options based on your needs.
 
-	config DEBUG_MSM8960_UART
-		bool "Kernel low-level debugging messages via MSM 8960 UART"
-		depends on ARCH_MSM8960
-		select MSM_HAS_DEBUG_UART_HS
-		select DEBUG_MSM_UART
+	config DEBUG_QCOM_UARTDM
+		bool "Kernel low-level debugging messages via QCOM UARTDM"
+		depends on ARCH_QCOM
 		help
 		  Say Y here if you want the debug print routines to direct
-		  their output to the serial port on MSM 8960 devices.
+		  their output to the serial port on Qualcomm devices.
 
-	config DEBUG_MSM8974_UART
-		bool "Kernel low-level debugging messages via MSM 8974 UART"
-		depends on ARCH_MSM8974
-		select MSM_HAS_DEBUG_UART_HS
-		select DEBUG_MSM_UART
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to the serial port on MSM 8974 devices.
+		  ARCH      DEBUG_UART_PHYS   DEBUG_UART_BASE
+		  APQ8084   0xf995e000        0xfa75e000
+		  MSM8X60   0x19c40000        0xf0040000
+		  MSM8960   0x16440000        0xf0040000
+		  MSM8974   0xf991e000        0xfa71e000
+
+		  Please adjust DEBUG_UART_PHYS and DEBUG_UART_BASE configuration
+		  options based on your needs.
 
 	config DEBUG_MVEBU_UART
 		bool "Kernel low-level debugging messages via MVEBU UART (old bootloaders)"
@@ -972,13 +963,23 @@ config DEBUG_IMX_UART_PORT
 						DEBUG_IMX51_UART || \
 						DEBUG_IMX53_UART || \
 						DEBUG_IMX6Q_UART || \
-						DEBUG_IMX6SL_UART
+						DEBUG_IMX6SL_UART || \
+						DEBUG_IMX6SX_UART
 	default 1
 	depends on ARCH_MXC
 	help
 	  Choose UART port on which kernel low-level debug messages
 	  should be output.
 
+config DEBUG_VF_UART_PORT
+	int "Vybrid Debug UART Port Selection" if DEBUG_VF_UART
+	default 1
+	range 0 3
+	depends on SOC_VF610
+	help
+	  Choose UART port on which kernel low-level debug messages
+	  should be output.
+
 config DEBUG_TEGRA_UART
 	bool
 	depends on ARCH_TEGRA
@@ -987,10 +988,6 @@ config DEBUG_STI_UART
 	bool
 	depends on ARCH_STI
 
-config DEBUG_MSM_UART
-	bool
-	depends on ARCH_MSM || ARCH_QCOM
-
 config DEBUG_LL_INCLUDE
 	string
 	default "debug/8250.S" if DEBUG_LL_UART_8250 || DEBUG_UART_8250
@@ -1007,8 +1004,9 @@ config DEBUG_LL_INCLUDE
 				 DEBUG_IMX51_UART || \
 				 DEBUG_IMX53_UART ||\
 				 DEBUG_IMX6Q_UART || \
-				 DEBUG_IMX6SL_UART
-	default "debug/msm.S" if DEBUG_MSM_UART
+				 DEBUG_IMX6SL_UART || \
+				 DEBUG_IMX6SX_UART
+	default "debug/msm.S" if DEBUG_MSM_UART || DEBUG_QCOM_UARTDM
 	default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART
 	default "debug/s3c24xx.S" if DEBUG_S3C24XX_UART
 	default "debug/sirf.S" if DEBUG_SIRFPRIMA2_UART1 || DEBUG_SIRFMARCO_UART1
@@ -1079,6 +1077,7 @@ config DEBUG_UART_PHYS
 	default 0x80230000 if DEBUG_PICOXCELL_UART
 	default 0x808c0000 if ARCH_EP93XX
 	default 0x90020000 if DEBUG_NSPIRE_CLASSIC_UART || DEBUG_NSPIRE_CX_UART
+	default 0xa9a00000 if DEBUG_MSM_UART
 	default 0xb0090000 if DEBUG_VEXPRESS_UART0_CRX
 	default 0xc0013000 if DEBUG_U300_UART
 	default 0xc8000000 if ARCH_IXP4XX && !CPU_BIG_ENDIAN
@@ -1094,6 +1093,7 @@ config DEBUG_UART_PHYS
 				ARCH_ORION5X
 	default 0xf7fc9000 if DEBUG_BERLIN_UART
 	default 0xf8b00000 if DEBUG_HI3716_UART
+	default 0xf991e000 if DEBUG_QCOM_UARTDM
 	default 0xfcb00000 if DEBUG_HI3620_UART
 	default 0xfe800000 if ARCH_IOP32X
 	default 0xffc02000 if DEBUG_SOCFPGA_UART
@@ -1102,11 +1102,13 @@ config DEBUG_UART_PHYS
 	default 0xfffff700 if ARCH_IOP33X
 	depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
 		DEBUG_LL_UART_EFM32 || \
-		DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_S3C24XX_UART
+		DEBUG_UART_8250 || DEBUG_UART_PL01X || \
+		DEBUG_MSM_UART || DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART
 
 config DEBUG_UART_VIRT
 	hex "Virtual base address of debug UART"
 	default 0xe0010fe0 if ARCH_RPC
+	default 0xe1000000 if DEBUG_MSM_UART
 	default 0xf0000be0 if ARCH_EBSA110
 	default 0xf0009000 if DEBUG_CNS3XXX
 	default 0xf01fb000 if DEBUG_NOMADIK_UART
@@ -1128,6 +1130,7 @@ config DEBUG_UART_VIRT
 	default 0xf7fc9000 if DEBUG_BERLIN_UART
 	default 0xf8009000 if DEBUG_VEXPRESS_UART0_CA9
 	default 0xf8090000 if DEBUG_VEXPRESS_UART0_RS1
+	default 0xfa71e000 if DEBUG_QCOM_UARTDM
 	default 0xfb009000 if DEBUG_REALVIEW_STD_PORT
 	default 0xfb10c000 if DEBUG_REALVIEW_PB1176_PORT
 	default 0xfd000000 if ARCH_SPEAR3XX || ARCH_SPEAR6XX
@@ -1166,7 +1169,8 @@ config DEBUG_UART_VIRT
 	default 0xff003000 if DEBUG_U300_UART
 	default DEBUG_UART_PHYS if !MMU
 	depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
-		DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_S3C24XX_UART
+		DEBUG_UART_8250 || DEBUG_UART_PL01X || \
+		DEBUG_MSM_UART || DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART
 
 config DEBUG_UART_8250_SHIFT
 	int "Register offset shift for the 8250 debug UART"