drm/i915: Parametrize the dphy and other spec specific parameters

The values of these parameters will be different for differnet panel
based on dsi rate, lane count, etc. Remove the hardcodings and make
these as parameters whch will be initialized in panel specific
sub-encoder implementaion.

This will also form groundwork for planned generic panel sub-encoder
implemntation based on VBT design enhancments to support multiple panels

v2: Mask away the port_bits before use

Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

1 files changed, 14 insertions, 15 deletions

diff --git a/drivers/gpu/drm/i915/intel_dsi.c b/drivers/gpu/drm/i915/intel_dsi.c
index 604fa6cee289..fabbf0d895cf 100644
--- a/drivers/gpu/drm/i915/intel_dsi.c
+++ b/drivers/gpu/drm/i915/intel_dsi.c
@@ -157,7 +157,8 @@ static void intel_dsi_enable(struct intel_encoder *encoder)
 		msleep(100);
 
 		/* assert ip_tg_enable signal */
-		temp = I915_READ(MIPI_PORT_CTRL(pipe));
+		temp = I915_READ(MIPI_PORT_CTRL(pipe)) & ~LANE_CONFIGURATION_MASK;
+		temp = temp | intel_dsi->port_bits;
 		I915_WRITE(MIPI_PORT_CTRL(pipe), temp | DPI_ENABLE);
 		POSTING_READ(MIPI_PORT_CTRL(pipe));
 	}
@@ -391,11 +392,7 @@ static void intel_dsi_mode_set(struct intel_encoder *intel_encoder)
 	I915_WRITE(MIPI_INTR_STAT(pipe), 0xffffffff);
 	I915_WRITE(MIPI_INTR_EN(pipe), 0xffffffff);
 
-	I915_WRITE(MIPI_DPHY_PARAM(pipe),
-		   0x3c << EXIT_ZERO_COUNT_SHIFT |
-		   0x1f << TRAIL_COUNT_SHIFT |
-		   0xc5 << CLK_ZERO_COUNT_SHIFT |
-		   0x1f << PREPARE_COUNT_SHIFT);
+	I915_WRITE(MIPI_DPHY_PARAM(pipe), intel_dsi->dphy_reg);
 
 	I915_WRITE(MIPI_DPI_RESOLUTION(pipe),
 		   adjusted_mode->vdisplay << VERTICAL_ADDRESS_SHIFT |
@@ -443,9 +440,9 @@ static void intel_dsi_mode_set(struct intel_encoder *intel_encoder)
 				       adjusted_mode->htotal,
 				       bpp, intel_dsi->lane_count) + 1);
 	}
-	I915_WRITE(MIPI_LP_RX_TIMEOUT(pipe), 8309); /* max */
-	I915_WRITE(MIPI_TURN_AROUND_TIMEOUT(pipe), 0x14); /* max */
-	I915_WRITE(MIPI_DEVICE_RESET_TIMER(pipe), 0xffff); /* max */
+	I915_WRITE(MIPI_LP_RX_TIMEOUT(pipe), intel_dsi->lp_rx_timeout);
+	I915_WRITE(MIPI_TURN_AROUND_TIMEOUT(pipe), intel_dsi->turn_arnd_val);
+	I915_WRITE(MIPI_DEVICE_RESET_TIMER(pipe), intel_dsi->rst_timer_val);
 
 	/* dphy stuff */
 
@@ -460,29 +457,31 @@ static void intel_dsi_mode_set(struct intel_encoder *intel_encoder)
 	 *
 	 * XXX: write MIPI_STOP_STATE_STALL?
 	 */
-	I915_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT(pipe), 0x46);
+	I915_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT(pipe),
+						intel_dsi->hs_to_lp_count);
 
 	/* XXX: low power clock equivalence in terms of byte clock. the number
 	 * of byte clocks occupied in one low power clock. based on txbyteclkhs
 	 * and txclkesc. txclkesc time / txbyteclk time * (105 +
 	 * MIPI_STOP_STATE_STALL) / 105.???
 	 */
-	I915_WRITE(MIPI_LP_BYTECLK(pipe), 4);
+	I915_WRITE(MIPI_LP_BYTECLK(pipe), intel_dsi->lp_byte_clk);
 
 	/* the bw essential for transmitting 16 long packets containing 252
 	 * bytes meant for dcs write memory command is programmed in this
 	 * register in terms of byte clocks. based on dsi transfer rate and the
 	 * number of lanes configured the time taken to transmit 16 long packets
 	 * in a dsi stream varies. */
-	I915_WRITE(MIPI_DBI_BW_CTRL(pipe), 0x820);
+	I915_WRITE(MIPI_DBI_BW_CTRL(pipe), intel_dsi->bw_timer);
 
 	I915_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT(pipe),
-		   0xa << LP_HS_SSW_CNT_SHIFT |
-		   0x14 << HS_LP_PWR_SW_CNT_SHIFT);
+		   intel_dsi->clk_lp_to_hs_count << LP_HS_SSW_CNT_SHIFT |
+		   intel_dsi->clk_hs_to_lp_count << HS_LP_PWR_SW_CNT_SHIFT);
 
 	if (is_vid_mode(intel_dsi))
 		I915_WRITE(MIPI_VIDEO_MODE_FORMAT(pipe),
-			   intel_dsi->video_mode_format);
+				intel_dsi->video_frmt_cfg_bits |
+				intel_dsi->video_mode_format);
 }
 
 static enum drm_connector_status