diff options
| -rw-r--r-- | drivers/mmc/host/sdhci-msm.c | 57 |
1 files changed, 55 insertions, 2 deletions
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c index edd30a23d36b..bb11916c58a1 100644 --- a/drivers/mmc/host/sdhci-msm.c +++ b/drivers/mmc/host/sdhci-msm.c @@ -78,12 +78,15 @@ #define CORE_HC_MCLK_SEL_DFLT (2 << 8) #define CORE_HC_MCLK_SEL_HS400 (3 << 8) #define CORE_HC_MCLK_SEL_MASK (3 << 8) +#define CORE_IO_PAD_PWR_SWITCH_EN (1 << 15) +#define CORE_IO_PAD_PWR_SWITCH (1 << 16) #define CORE_HC_SELECT_IN_EN BIT(18) #define CORE_HC_SELECT_IN_HS400 (6 << 19) #define CORE_HC_SELECT_IN_MASK (7 << 19) #define CORE_3_0V_SUPPORT (1 << 25) #define CORE_1_8V_SUPPORT (1 << 26) +#define CORE_VOLT_SUPPORT (CORE_3_0V_SUPPORT | CORE_1_8V_SUPPORT) #define CORE_CSR_CDC_CTLR_CFG0 0x130 #define CORE_SW_TRIG_FULL_CALIB BIT(16) @@ -1109,7 +1112,7 @@ static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq) u32 irq_status, irq_ack = 0; int retry = 10; u32 pwr_state = 0, io_level = 0; - + u32 config; irq_status = readl_relaxed(msm_host->core_mem + CORE_PWRCTL_STATUS); irq_status &= INT_MASK; @@ -1166,6 +1169,38 @@ static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq) */ writel_relaxed(irq_ack, msm_host->core_mem + CORE_PWRCTL_CTL); + /* + * If we don't have info regarding the voltage levels supported by + * regulators, don't change the IO PAD PWR SWITCH. + */ + if (msm_host->caps_0 & CORE_VOLT_SUPPORT) { + u32 new_config; + /* + * We should unset IO PAD PWR switch only if the register write + * can set IO lines high and the regulator also switches to 3 V. + * Else, we should keep the IO PAD PWR switch set. + * This is applicable to certain targets where eMMC vccq supply + * is only 1.8V. In such targets, even during REQ_IO_HIGH, the + * IO PAD PWR switch must be kept set to reflect actual + * regulator voltage. This way, during initialization of + * controllers with only 1.8V, we will set the IO PAD bit + * without waiting for a REQ_IO_LOW. + */ + config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC); + new_config = config; + + if ((io_level & REQ_IO_HIGH) && + (msm_host->caps_0 & CORE_3_0V_SUPPORT)) + new_config &= ~CORE_IO_PAD_PWR_SWITCH; + else if ((io_level & REQ_IO_LOW) || + (msm_host->caps_0 & CORE_1_8V_SUPPORT)) + new_config |= CORE_IO_PAD_PWR_SWITCH; + + if (config ^ new_config) + writel_relaxed(new_config, + host->ioaddr + CORE_VENDOR_SPEC); + } + if (pwr_state) msm_host->curr_pwr_state = pwr_state; if (io_level) @@ -1322,7 +1357,8 @@ static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host) { struct mmc_host *mmc = msm_host->mmc; struct regulator *supply = mmc->supply.vqmmc; - u32 caps = 0; + u32 caps = 0, config; + struct sdhci_host *host = mmc_priv(mmc); if (!IS_ERR(mmc->supply.vqmmc)) { if (regulator_is_supported_voltage(supply, 1700000, 1950000)) @@ -1335,6 +1371,23 @@ static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host) mmc_hostname(mmc)); } + if (caps) { + /* + * Set the PAD_PWR_SWITCH_EN bit so that the PAD_PWR_SWITCH + * bit can be used as required later on. + */ + u32 io_level = msm_host->curr_io_level; + + config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC); + config |= CORE_IO_PAD_PWR_SWITCH_EN; + + if ((io_level & REQ_IO_HIGH) && (caps & CORE_3_0V_SUPPORT)) + config &= ~CORE_IO_PAD_PWR_SWITCH; + else if ((io_level & REQ_IO_LOW) || (caps & CORE_1_8V_SUPPORT)) + config |= CORE_IO_PAD_PWR_SWITCH; + + writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC); + } msm_host->caps_0 |= caps; pr_debug("%s: supported caps: 0x%08x\n", mmc_hostname(mmc), caps); } |