diff options
| -rw-r--r-- | drivers/net/wireless/ath/ath6kl/cfg80211.c | 8 | ||||
| -rw-r--r-- | include/net/cfg80211.h | 48 | ||||
| -rw-r--r-- | include/uapi/linux/nl80211.h | 16 | ||||
| -rw-r--r-- | net/mac80211/cfg.c | 125 | ||||
| -rw-r--r-- | net/wireless/nl80211.c | 288 |
5 files changed, 311 insertions, 174 deletions
diff --git a/drivers/net/wireless/ath/ath6kl/cfg80211.c b/drivers/net/wireless/ath/ath6kl/cfg80211.c index 752ffc4f4166..28c413f861a2 100644 --- a/drivers/net/wireless/ath/ath6kl/cfg80211.c +++ b/drivers/net/wireless/ath/ath6kl/cfg80211.c @@ -2990,13 +2990,15 @@ static int ath6kl_change_station(struct wiphy *wiphy, struct net_device *dev, { struct ath6kl *ar = ath6kl_priv(dev); struct ath6kl_vif *vif = netdev_priv(dev); + int err; if (vif->nw_type != AP_NETWORK) return -EOPNOTSUPP; - /* Use this only for authorizing/unauthorizing a station */ - if (!(params->sta_flags_mask & BIT(NL80211_STA_FLAG_AUTHORIZED))) - return -EOPNOTSUPP; + err = cfg80211_check_station_change(wiphy, params, + CFG80211_STA_AP_MLME_CLIENT); + if (err) + return err; if (params->sta_flags_set & BIT(NL80211_STA_FLAG_AUTHORIZED)) return ath6kl_wmi_ap_set_mlme(ar->wmi, vif->fw_vif_idx, diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 7ca321d2b599..ed2b08da3b93 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -678,6 +678,49 @@ struct station_parameters { }; /** + * enum cfg80211_station_type - the type of station being modified + * @CFG80211_STA_AP_CLIENT: client of an AP interface + * @CFG80211_STA_AP_MLME_CLIENT: client of an AP interface that has + * the AP MLME in the device + * @CFG80211_STA_AP_STA: AP station on managed interface + * @CFG80211_STA_IBSS: IBSS station + * @CFG80211_STA_TDLS_PEER_SETUP: TDLS peer on managed interface (dummy entry + * while TDLS setup is in progress, it moves out of this state when + * being marked authorized; use this only if TDLS with external setup is + * supported/used) + * @CFG80211_STA_TDLS_PEER_ACTIVE: TDLS peer on managed interface (active + * entry that is operating, has been marked authorized by userspace) + * @CFG80211_STA_MESH_PEER_NONSEC: peer on mesh interface (non-secured) + * @CFG80211_STA_MESH_PEER_SECURE: peer on mesh interface (secured) + */ +enum cfg80211_station_type { + CFG80211_STA_AP_CLIENT, + CFG80211_STA_AP_MLME_CLIENT, + CFG80211_STA_AP_STA, + CFG80211_STA_IBSS, + CFG80211_STA_TDLS_PEER_SETUP, + CFG80211_STA_TDLS_PEER_ACTIVE, + CFG80211_STA_MESH_PEER_NONSEC, + CFG80211_STA_MESH_PEER_SECURE, +}; + +/** + * cfg80211_check_station_change - validate parameter changes + * @wiphy: the wiphy this operates on + * @params: the new parameters for a station + * @statype: the type of station being modified + * + * Utility function for the @change_station driver method. Call this function + * with the appropriate station type looking up the station (and checking that + * it exists). It will verify whether the station change is acceptable, and if + * not will return an error code. Note that it may modify the parameters for + * backward compatibility reasons, so don't use them before calling this. + */ +int cfg80211_check_station_change(struct wiphy *wiphy, + struct station_parameters *params, + enum cfg80211_station_type statype); + +/** * enum station_info_flags - station information flags * * Used by the driver to indicate which info in &struct station_info @@ -1770,9 +1813,8 @@ struct cfg80211_gtk_rekey_data { * @change_station: Modify a given station. Note that flags changes are not much * validated in cfg80211, in particular the auth/assoc/authorized flags * might come to the driver in invalid combinations -- make sure to check - * them, also against the existing state! Also, supported_rates changes are - * not checked in station mode -- drivers need to reject (or ignore) them - * for anything but TDLS peers. + * them, also against the existing state! Drivers must call + * cfg80211_check_station_change() to validate the information. * @get_station: get station information for the station identified by @mac * @dump_station: dump station callback -- resume dump at index @idx * diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index 7dcc69f73d2c..523ed3d65b41 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -36,7 +36,21 @@ * The station is still assumed to belong to the AP interface it was added * to. * - * TODO: need more info? + * Station handling varies per interface type and depending on the driver's + * capabilities. + * + * For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS + * and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows: + * - a setup station entry is added, not yet authorized, without any rate + * or capability information, this just exists to avoid race conditions + * - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid + * to add rate and capability information to the station and at the same + * time mark it authorized. + * - %NL80211_TDLS_ENABLE_LINK is then used + * - after this, the only valid operation is to remove it by tearing down + * the TDLS link (%NL80211_TDLS_DISABLE_LINK) + * + * TODO: need more info for other interface types */ /** diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c index ca28405d5f65..c115f82c037c 100644 --- a/net/mac80211/cfg.c +++ b/net/mac80211/cfg.c @@ -1177,6 +1177,18 @@ static int sta_apply_parameters(struct ieee80211_local *local, mask |= BIT(NL80211_STA_FLAG_ASSOCIATED); if (set & BIT(NL80211_STA_FLAG_AUTHENTICATED)) set |= BIT(NL80211_STA_FLAG_ASSOCIATED); + } else if (test_sta_flag(sta, WLAN_STA_TDLS_PEER)) { + /* + * TDLS -- everything follows authorized, but + * only becoming authorized is possible, not + * going back + */ + if (set & BIT(NL80211_STA_FLAG_AUTHORIZED)) { + set |= BIT(NL80211_STA_FLAG_AUTHENTICATED) | + BIT(NL80211_STA_FLAG_ASSOCIATED); + mask |= BIT(NL80211_STA_FLAG_AUTHENTICATED) | + BIT(NL80211_STA_FLAG_ASSOCIATED); + } } ret = sta_apply_auth_flags(local, sta, mask, set); @@ -1261,9 +1273,8 @@ static int sta_apply_parameters(struct ieee80211_local *local, if (ieee80211_vif_is_mesh(&sdata->vif)) { #ifdef CONFIG_MAC80211_MESH u32 changed = 0; - if (sdata->u.mesh.security & IEEE80211_MESH_SEC_SECURED && - (params->sta_modify_mask & - STATION_PARAM_APPLY_PLINK_STATE)) { + + if (params->sta_modify_mask & STATION_PARAM_APPLY_PLINK_STATE) { switch (params->plink_state) { case NL80211_PLINK_ESTAB: if (sta->plink_state != NL80211_PLINK_ESTAB) @@ -1294,21 +1305,18 @@ static int sta_apply_parameters(struct ieee80211_local *local, /* nothing */ break; } - } else if (params->sta_modify_mask & - STATION_PARAM_APPLY_PLINK_STATE) { - return -EINVAL; - } else { - switch (params->plink_action) { - case NL80211_PLINK_ACTION_NO_ACTION: - /* nothing */ - break; - case NL80211_PLINK_ACTION_OPEN: - changed |= mesh_plink_open(sta); - break; - case NL80211_PLINK_ACTION_BLOCK: - changed |= mesh_plink_block(sta); - break; - } + } + + switch (params->plink_action) { + case NL80211_PLINK_ACTION_NO_ACTION: + /* nothing */ + break; + case NL80211_PLINK_ACTION_OPEN: + changed |= mesh_plink_open(sta); + break; + case NL80211_PLINK_ACTION_BLOCK: + changed |= mesh_plink_block(sta); + break; } if (params->local_pm) @@ -1354,8 +1362,10 @@ static int ieee80211_add_station(struct wiphy *wiphy, struct net_device *dev, * defaults -- if userspace wants something else we'll * change it accordingly in sta_apply_parameters() */ - sta_info_pre_move_state(sta, IEEE80211_STA_AUTH); - sta_info_pre_move_state(sta, IEEE80211_STA_ASSOC); + if (!(params->sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER))) { + sta_info_pre_move_state(sta, IEEE80211_STA_AUTH); + sta_info_pre_move_state(sta, IEEE80211_STA_ASSOC); + } err = sta_apply_parameters(local, sta, params); if (err) { @@ -1364,8 +1374,8 @@ static int ieee80211_add_station(struct wiphy *wiphy, struct net_device *dev, } /* - * for TDLS, rate control should be initialized only when supported - * rates are known. + * for TDLS, rate control should be initialized only when + * rates are known and station is marked authorized */ if (!test_sta_flag(sta, WLAN_STA_TDLS_PEER)) rate_control_rate_init(sta); @@ -1402,50 +1412,67 @@ static int ieee80211_del_station(struct wiphy *wiphy, struct net_device *dev, } static int ieee80211_change_station(struct wiphy *wiphy, - struct net_device *dev, - u8 *mac, + struct net_device *dev, u8 *mac, struct station_parameters *params) { struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev); struct ieee80211_local *local = wiphy_priv(wiphy); struct sta_info *sta; struct ieee80211_sub_if_data *vlansdata; + enum cfg80211_station_type statype; int err; mutex_lock(&local->sta_mtx); sta = sta_info_get_bss(sdata, mac); if (!sta) { - mutex_unlock(&local->sta_mtx); - return -ENOENT; + err = -ENOENT; + goto out_err; } - /* in station mode, some updates are only valid with TDLS */ - if (sdata->vif.type == NL80211_IFTYPE_STATION && - (params->supported_rates || params->ht_capa || params->vht_capa || - params->sta_modify_mask || - (params->sta_flags_mask & BIT(NL80211_STA_FLAG_WME))) && - !test_sta_flag(sta, WLAN_STA_TDLS_PEER)) { - mutex_unlock(&local->sta_mtx); - return -EINVAL; + switch (sdata->vif.type) { + case NL80211_IFTYPE_MESH_POINT: + if (sdata->u.mesh.security & IEEE80211_MESH_SEC_SECURED) + statype = CFG80211_STA_MESH_PEER_SECURE; + else + statype = CFG80211_STA_MESH_PEER_NONSEC; + break; + case NL80211_IFTYPE_ADHOC: + statype = CFG80211_STA_IBSS; + break; + case NL80211_IFTYPE_STATION: + if (!test_sta_flag(sta, WLAN_STA_TDLS_PEER)) { + statype = CFG80211_STA_AP_STA; + break; + } + if (test_sta_flag(sta, WLAN_STA_AUTHORIZED)) + statype = CFG80211_STA_TDLS_PEER_ACTIVE; + else + statype = CFG80211_STA_TDLS_PEER_SETUP; + break; + case NL80211_IFTYPE_AP: + case NL80211_IFTYPE_AP_VLAN: + statype = CFG80211_STA_AP_CLIENT; + break; + default: + err = -EOPNOTSUPP; + goto out_err; } + err = cfg80211_check_station_change(wiphy, params, statype); + if (err) + goto out_err; + if (params->vlan && params->vlan != sta->sdata->dev) { bool prev_4addr = false; bool new_4addr = false; vlansdata = IEEE80211_DEV_TO_SUB_IF(params->vlan); - if (vlansdata->vif.type != NL80211_IFTYPE_AP_VLAN && - vlansdata->vif.type != NL80211_IFTYPE_AP) { - mutex_unlock(&local->sta_mtx); - return -EINVAL; - } - if (params->vlan->ieee80211_ptr->use_4addr) { if (vlansdata->u.vlan.sta) { - mutex_unlock(&local->sta_mtx); - return -EBUSY; + err = -EBUSY; + goto out_err; } rcu_assign_pointer(vlansdata->u.vlan.sta, sta); @@ -1472,12 +1499,12 @@ static int ieee80211_change_station(struct wiphy *wiphy, } err = sta_apply_parameters(local, sta, params); - if (err) { - mutex_unlock(&local->sta_mtx); - return err; - } + if (err) + goto out_err; - if (test_sta_flag(sta, WLAN_STA_TDLS_PEER) && params->supported_rates) + /* When peer becomes authorized, init rate control as well */ + if (test_sta_flag(sta, WLAN_STA_TDLS_PEER) && + test_sta_flag(sta, WLAN_STA_AUTHORIZED)) rate_control_rate_init(sta); mutex_unlock(&local->sta_mtx); @@ -1487,7 +1514,11 @@ static int ieee80211_change_station(struct wiphy *wiphy, ieee80211_recalc_ps(local, -1); ieee80211_recalc_ps_vif(sdata); } + return 0; +out_err: + mutex_unlock(&local->sta_mtx); + return err; } #ifdef CONFIG_MAC80211_MESH diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c index 9e7c10420da8..83151a50e5ad 100644 --- a/net/wireless/nl80211.c +++ b/net/wireless/nl80211.c @@ -2967,6 +2967,7 @@ static int parse_station_flags(struct genl_info *info, sta_flags = nla_data(nla); params->sta_flags_mask = sta_flags->mask; params->sta_flags_set = sta_flags->set; + params->sta_flags_set &= params->sta_flags_mask; if ((params->sta_flags_mask | params->sta_flags_set) & BIT(__NL80211_STA_FLAG_INVALID)) return -EINVAL; @@ -3320,6 +3321,136 @@ static int nl80211_get_station(struct sk_buff *skb, struct genl_info *info) return genlmsg_reply(msg, info); } +int cfg80211_check_station_change(struct wiphy *wiphy, + struct station_parameters *params, + enum cfg80211_station_type statype) +{ + if (params->listen_interval != -1) + return -EINVAL; + if (params->aid) + return -EINVAL; + + /* When you run into this, adjust the code below for the new flag */ + BUILD_BUG_ON(NL80211_STA_FLAG_MAX != 7); + + switch (statype) { + case CFG80211_STA_MESH_PEER_NONSEC: + case CFG80211_STA_MESH_PEER_SECURE: + /* + * No ignoring the TDLS flag here -- the userspace mesh + * code doesn't have the bug of including TDLS in the + * mask everywhere. + */ + if (params->sta_flags_mask & + ~(BIT(NL80211_STA_FLAG_AUTHENTICATED) | + BIT(NL80211_STA_FLAG_MFP) | + BIT(NL80211_STA_FLAG_AUTHORIZED))) + return -EINVAL; + break; + case CFG80211_STA_TDLS_PEER_SETUP: + case CFG80211_STA_TDLS_PEER_ACTIVE: + if (!(params->sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER))) + return -EINVAL; + /* ignore since it can't change */ + params->sta_flags_mask &= ~BIT(NL80211_STA_FLAG_TDLS_PEER); + break; + default: + /* disallow mesh-specific things */ + if (params->plink_action != NL80211_PLINK_ACTION_NO_ACTION) + return -EINVAL; + if (params->local_pm) + return -EINVAL; + if (params->sta_modify_mask & STATION_PARAM_APPLY_PLINK_STATE) + return -EINVAL; + } + + if (statype != CFG80211_STA_TDLS_PEER_SETUP && + statype != CFG80211_STA_TDLS_PEER_ACTIVE) { + /* TDLS can't be set, ... */ + if (params->sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER)) + return -EINVAL; + /* + * ... but don't bother the driver with it. This works around + * a hostapd/wpa_supplicant issue -- it always includes the + * TLDS_PEER flag in the mask even for AP mode. + */ + params->sta_flags_mask &= ~BIT(NL80211_STA_FLAG_TDLS_PEER); + } + + if (statype != CFG80211_STA_TDLS_PEER_SETUP) { + /* reject other things that can't change */ + if (params->sta_modify_mask & STATION_PARAM_APPLY_UAPSD) + return -EINVAL; + if (params->sta_modify_mask & STATION_PARAM_APPLY_CAPABILITY) + return -EINVAL; + if (params->supported_rates) + return -EINVAL; + if (params->ext_capab || params->ht_capa || params->vht_capa) + return -EINVAL; + } + + if (statype != CFG80211_STA_AP_CLIENT) { + if (params->vlan) + return -EINVAL; + } + + switch (statype) { + case CFG80211_STA_AP_MLME_CLIENT: + /* Use this only for authorizing/unauthorizing a station */ + if (!(params->sta_flags_mask & BIT(NL80211_STA_FLAG_AUTHORIZED))) + return -EOPNOTSUPP; + break; + case CFG80211_STA_AP_CLIENT: + /* accept only the listed bits */ + if (params->sta_flags_mask & + ~(BIT(NL80211_STA_FLAG_AUTHORIZED) | + BIT(NL80211_STA_FLAG_AUTHENTICATED) | + BIT(NL80211_STA_FLAG_ASSOCIATED) | + BIT(NL80211_STA_FLAG_SHORT_PREAMBLE) | + BIT(NL80211_STA_FLAG_WME) | + BIT(NL80211_STA_FLAG_MFP))) + return -EINVAL; + + /* but authenticated/associated only if driver handles it */ + if (!(wiphy->features & NL80211_FEATURE_FULL_AP_CLIENT_STATE) && + params->sta_flags_mask & + (BIT(NL80211_STA_FLAG_AUTHENTICATED) | + BIT(NL80211_STA_FLAG_ASSOCIATED))) + return -EINVAL; + break; + case CFG80211_STA_IBSS: + case CFG80211_STA_AP_STA: + /* reject any changes other than AUTHORIZED */ + if (params->sta_flags_mask & ~BIT(NL80211_STA_FLAG_AUTHORIZED)) + return -EINVAL; + break; + case CFG80211_STA_TDLS_PEER_SETUP: + /* reject any changes other than AUTHORIZED or WME */ + if (params->sta_flags_mask & ~(BIT(NL80211_STA_FLAG_AUTHORIZED) | + BIT(NL80211_STA_FLAG_WME))) + return -EINVAL; + /* force (at least) rates when authorizing */ + if (params->sta_flags_set & BIT(NL80211_STA_FLAG_AUTHORIZED) && + !params->supported_rates) + return -EINVAL; + break; + case CFG80211_STA_TDLS_PEER_ACTIVE: + /* reject any changes */ + return -EINVAL; + case CFG80211_STA_MESH_PEER_NONSEC: + if (params->sta_modify_mask & STATION_PARAM_APPLY_PLINK_STATE) + return -EINVAL; + break; + case CFG80211_STA_MESH_PEER_SECURE: + if (params->plink_action != NL80211_PLINK_ACTION_NO_ACTION) + return -EINVAL; + break; + } + + return 0; +} +EXPORT_SYMBOL(cfg80211_check_station_change); + /* * Get vlan interface making sure it is running and on the right wiphy. */ @@ -3342,6 +3473,13 @@ static struct net_device *get_vlan(struct genl_info *info, goto error; } + if (v->ieee80211_ptr->iftype != NL80211_IFTYPE_AP_VLAN && + v->ieee80211_ptr->iftype != NL80211_IFTYPE_AP && + v->ieee80211_ptr->iftype != NL80211_IFTYPE_P2P_GO) { + ret = -EINVAL; + goto error; + } + if (!netif_running(v)) { ret = -ENETDOWN; goto error; @@ -3410,15 +3548,18 @@ static int nl80211_set_station_tdls(struct genl_info *info, static int nl80211_set_station(struct sk_buff *skb, struct genl_info *info) { struct cfg80211_registered_device *rdev = info->user_ptr[0]; - int err; struct net_device *dev = info->user_ptr[1]; struct station_parameters params; - u8 *mac_addr = NULL; + u8 *mac_addr; + int err; memset(¶ms, 0, sizeof(params)); params.listen_interval = -1; + if (!rdev->ops->change_station) + return -EOPNOTSUPP; + if (info->attrs[NL80211_ATTR_STA_AID]) return -EINVAL; @@ -3450,9 +3591,6 @@ static int nl80211_set_station(struct sk_buff *skb, struct genl_info *info) if (info->attrs[NL80211_ATTR_STA_LISTEN_INTERVAL]) return -EINVAL; - if (!rdev->ops->change_station) - return -EOPNOTSUPP; - if (parse_station_flags(info, dev->ieee80211_ptr->iftype, ¶ms)) return -EINVAL; @@ -3482,133 +3620,33 @@ static int nl80211_set_station(struct sk_buff *skb, struct genl_info *info) params.local_pm = pm; } + /* Include parameters for TDLS peer (will check later) */ + err = nl80211_set_station_tdls(info, ¶ms); + if (err) + return err; + + params.vlan = get_vlan(info, rdev); + if (IS_ERR(params.vlan)) + return PTR_ERR(params.vlan); + switch (dev->ieee80211_ptr->iftype) { case NL80211_IFTYPE_AP: case NL80211_IFTYPE_AP_VLAN: case NL80211_IFTYPE_P2P_GO: - /* disallow mesh-specific things */ - if (params.plink_action) - return -EINVAL; - if (params.local_pm) - return -EINVAL; - if (params.sta_modify_mask & STATION_PARAM_APPLY_PLINK_STATE) - return -EINVAL; - - /* TDLS can't be set, ... */ - if (params.sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER)) - return -EINVAL; - /* - * ... but don't bother the driver with it. This works around - * a hostapd/wpa_supplicant issue -- it always includes the - * TLDS_PEER flag in the mask even for AP mode. - */ - params.sta_flags_mask &= ~BIT(NL80211_STA_FLAG_TDLS_PEER); - - /* accept only the listed bits */ - if (params.sta_flags_mask & - ~(BIT(NL80211_STA_FLAG_AUTHORIZED) | - BIT(NL80211_STA_FLAG_AUTHENTICATED) | - BIT(NL80211_STA_FLAG_ASSOCIATED) | - BIT(NL80211_STA_FLAG_SHORT_PREAMBLE) | - BIT(NL80211_STA_FLAG_WME) | - BIT(NL80211_STA_FLAG_MFP))) - return -EINVAL; - - /* but authenticated/associated only if driver handles it */ - if (!(rdev->wiphy.features & - NL80211_FEATURE_FULL_AP_CLIENT_STATE) && - params.sta_flags_mask & - (BIT(NL80211_STA_FLAG_AUTHENTICATED) | - BIT(NL80211_STA_FLAG_ASSOCIATED))) - return -EINVAL; - - /* reject other things that can't change */ - if (params.supported_rates) - return -EINVAL; - if (info->attrs[NL80211_ATTR_STA_CAPABILITY]) - return -EINVAL; - if (info->attrs[NL80211_ATTR_STA_EXT_CAPABILITY]) - return -EINVAL; - if (info->attrs[NL80211_ATTR_HT_CAPABILITY] || - info->attrs[NL80211_ATTR_VHT_CAPABILITY]) - return -EINVAL; - - /* must be last in here for error handling */ - params.vlan = get_vlan(info, rdev); - if (IS_ERR(params.vlan)) - return PTR_ERR(params.vlan); - break; case NL80211_IFTYPE_P2P_CLIENT: case NL80211_IFTYPE_STATION: - /* - * Don't allow userspace to change the TDLS_PEER flag, - * but silently ignore attempts to change it since we - * don't have state here to verify that it doesn't try - * to change the flag. - */ - params.sta_flags_mask &= ~BIT(NL80211_STA_FLAG_TDLS_PEER); - /* Include parameters for TDLS peer (driver will check) */ - err = nl80211_set_station_tdls(info, ¶ms); - if (err) - return err; - /* disallow things sta doesn't support */ - if (params.plink_action) - return -EINVAL; - if (params.local_pm) - return -EINVAL; - if (params.sta_modify_mask & STATION_PARAM_APPLY_PLINK_STATE) - return -EINVAL; - /* reject any changes other than AUTHORIZED or WME (for TDLS) */ - if (params.sta_flags_mask & ~(BIT(NL80211_STA_FLAG_AUTHORIZED) | - BIT(NL80211_STA_FLAG_WME))) - return -EINVAL; - break; case NL80211_IFTYPE_ADHOC: - /* disallow things sta doesn't support */ - if (params.plink_action) - return -EINVAL; - if (params.local_pm) - return -EINVAL; - if (params.sta_modify_mask & STATION_PARAM_APPLY_PLINK_STATE) - return -EINVAL; - if (info->attrs[NL80211_ATTR_HT_CAPABILITY] || - info->attrs[NL80211_ATTR_VHT_CAPABILITY]) - return -EINVAL; - /* reject any changes other than AUTHORIZED */ - if (params.sta_flags_mask & ~BIT(NL80211_STA_FLAG_AUTHORIZED)) - return -EINVAL; - break; case NL80211_IFTYPE_MESH_POINT: - /* disallow things mesh doesn't support */ - if (params.vlan) - return -EINVAL; - if (params.supported_rates) - return -EINVAL; - if (info->attrs[NL80211_ATTR_STA_CAPABILITY]) - return -EINVAL; - if (info->attrs[NL80211_ATTR_STA_EXT_CAPABILITY]) - return -EINVAL; - if (info->attrs[NL80211_ATTR_HT_CAPABILITY] || - info->attrs[NL80211_ATTR_VHT_CAPABILITY]) - return -EINVAL; - /* - * No special handling for TDLS here -- the userspace - * mesh code doesn't have this bug. - */ - if (params.sta_flags_mask & - ~(BIT(NL80211_STA_FLAG_AUTHENTICATED) | - BIT(NL80211_STA_FLAG_MFP) | - BIT(NL80211_STA_FLAG_AUTHORIZED))) - return -EINVAL; break; default: - return -EOPNOTSUPP; + err = -EOPNOTSUPP; + goto out_put_vlan; } - /* be aware of params.vlan when changing code here */ - + /* driver will call cfg80211_check_station_change() */ err = rdev_change_station(rdev, dev, mac_addr, ¶ms); + out_put_vlan: if (params.vlan) dev_put(params.vlan); @@ -3687,6 +3725,9 @@ static int nl80211_new_station(struct sk_buff *skb, struct genl_info *info) if (parse_station_flags(info, dev->ieee80211_ptr->iftype, ¶ms)) return -EINVAL; + /* When you run into this, adjust the code below for the new flag */ + BUILD_BUG_ON(NL80211_STA_FLAG_MAX != 7); + switch (dev->ieee80211_ptr->iftype) { case NL80211_IFTYPE_AP: case NL80211_IFTYPE_AP_VLAN: @@ -3730,8 +3771,10 @@ static int nl80211_new_station(struct sk_buff *skb, struct genl_info *info) /* ignore uAPSD data */ params.sta_modify_mask &= ~STATION_PARAM_APPLY_UAPSD; - /* associated is disallowed */ - if (params.sta_flags_mask & BIT(NL80211_STA_FLAG_ASSOCIATED)) + /* these are disallowed */ + if (params.sta_flags_mask & + (BIT(NL80211_STA_FLAG_ASSOCIATED) | + BIT(NL80211_STA_FLAG_AUTHENTICATED))) return -EINVAL; /* Only TDLS peers can be added */ if (!(params.sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER))) @@ -3742,6 +3785,11 @@ static int nl80211_new_station(struct sk_buff *skb, struct genl_info *info) /* ... with external setup is supported */ if (!(rdev->wiphy.flags & WIPHY_FLAG_TDLS_EXTERNAL_SETUP)) return -EOPNOTSUPP; + /* + * Older wpa_supplicant versions always mark the TDLS peer + * as authorized, but it shouldn't yet be. + */ + params.sta_flags_mask &= ~BIT(NL80211_STA_FLAG_AUTHORIZED); break; default: return -EOPNOTSUPP; |