summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree')
-rw-r--r--Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt27
-rw-r--r--Documentation/devicetree/bindings/gnss/gnss.txt1
-rw-r--r--Documentation/devicetree/bindings/gnss/mediatek.txt35
-rw-r--r--Documentation/devicetree/bindings/gnss/sirfstar.txt1
-rw-r--r--Documentation/devicetree/bindings/interconnect/interconnect.txt60
-rw-r--r--Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt24
-rw-r--r--Documentation/devicetree/bindings/misc/qcom,fastrpc.txt78
-rw-r--r--Documentation/devicetree/bindings/nvmem/imx-ocotp.txt4
-rw-r--r--Documentation/devicetree/bindings/vendor-prefixes.txt1
9 files changed, 230 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt
new file mode 100644
index 000000000000..936fbdf12815
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt
@@ -0,0 +1,27 @@
+* PTN5150 CC (Configuration Channel) Logic device
+
+PTN5150 is a small thin low power CC logic chip supporting the USB Type-C
+connector application with CC control logic detection and indication functions.
+It is interfaced to the host controller using an I2C interface.
+
+Required properties:
+- compatible: should be "nxp,ptn5150"
+- reg: specifies the I2C slave address of the device
+- int-gpio: should contain a phandle and GPIO specifier for the GPIO pin
+ connected to the PTN5150's INTB pin.
+- vbus-gpio: should contain a phandle and GPIO specifier for the GPIO pin which
+ is used to control VBUS.
+- pinctrl-names : a pinctrl state named "default" must be defined.
+- pinctrl-0 : phandle referencing pin configuration of interrupt and vbus
+ control.
+
+Example:
+ ptn5150@1d {
+ compatible = "nxp,ptn5150";
+ reg = <0x1d>;
+ int-gpio = <&msmgpio 78 GPIO_ACTIVE_HIGH>;
+ vbus-gpio = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ptn5150_default>;
+ status = "okay";
+ };
diff --git a/Documentation/devicetree/bindings/gnss/gnss.txt b/Documentation/devicetree/bindings/gnss/gnss.txt
index f1e4a2ff47c5..f547bd4549fe 100644
--- a/Documentation/devicetree/bindings/gnss/gnss.txt
+++ b/Documentation/devicetree/bindings/gnss/gnss.txt
@@ -17,6 +17,7 @@ Required properties:
represents
Optional properties:
+- lna-supply : Separate supply for an LNA
- enable-gpios : GPIO used to enable the device
- timepulse-gpios : Time pulse GPIO
diff --git a/Documentation/devicetree/bindings/gnss/mediatek.txt b/Documentation/devicetree/bindings/gnss/mediatek.txt
new file mode 100644
index 000000000000..80cb802813c5
--- /dev/null
+++ b/Documentation/devicetree/bindings/gnss/mediatek.txt
@@ -0,0 +1,35 @@
+Mediatek-based GNSS Receiver DT binding
+
+Mediatek chipsets are used in GNSS-receiver modules produced by several
+vendors and can use a UART interface.
+
+Please see Documentation/devicetree/bindings/gnss/gnss.txt for generic
+properties.
+
+Required properties:
+
+- compatible : Must be
+
+ "globaltop,pa6h"
+
+- vcc-supply : Main voltage regulator (pin name: VCC)
+
+Optional properties:
+
+- current-speed : Default UART baud rate
+- gnss-fix-gpios : GPIO used to determine device position fix state
+ (pin name: FIX, 3D_FIX)
+- reset-gpios : GPIO used to reset the device (pin name: RESET, NRESET)
+- timepulse-gpios : Time pulse GPIO (pin name: PPS1, 1PPS)
+- vbackup-supply : Backup voltage regulator (pin name: VBAT, VBACKUP)
+
+Example:
+
+serial@1234 {
+ compatible = "ns16550a";
+
+ gnss {
+ compatible = "globaltop,pa6h";
+ vcc-supply = <&vcc_3v3>;
+ };
+};
diff --git a/Documentation/devicetree/bindings/gnss/sirfstar.txt b/Documentation/devicetree/bindings/gnss/sirfstar.txt
index 648d183cdb77..f4252b6b660b 100644
--- a/Documentation/devicetree/bindings/gnss/sirfstar.txt
+++ b/Documentation/devicetree/bindings/gnss/sirfstar.txt
@@ -12,6 +12,7 @@ Required properties:
"fastrax,uc430"
"linx,r4"
+ "wi2wi,w2sg0004"
"wi2wi,w2sg0008i"
"wi2wi,w2sg0084i"
diff --git a/Documentation/devicetree/bindings/interconnect/interconnect.txt b/Documentation/devicetree/bindings/interconnect/interconnect.txt
new file mode 100644
index 000000000000..5a3c575b387a
--- /dev/null
+++ b/Documentation/devicetree/bindings/interconnect/interconnect.txt
@@ -0,0 +1,60 @@
+Interconnect Provider Device Tree Bindings
+=========================================
+
+The purpose of this document is to define a common set of generic interconnect
+providers/consumers properties.
+
+
+= interconnect providers =
+
+The interconnect provider binding is intended to represent the interconnect
+controllers in the system. Each provider registers a set of interconnect
+nodes, which expose the interconnect related capabilities of the interconnect
+to consumer drivers. These capabilities can be throughput, latency, priority
+etc. The consumer drivers set constraints on interconnect path (or endpoints)
+depending on the use case. Interconnect providers can also be interconnect
+consumers, such as in the case where two network-on-chip fabrics interface
+directly.
+
+Required properties:
+- compatible : contains the interconnect provider compatible string
+- #interconnect-cells : number of cells in a interconnect specifier needed to
+ encode the interconnect node id
+
+Example:
+
+ snoc: interconnect@580000 {
+ compatible = "qcom,msm8916-snoc";
+ #interconnect-cells = <1>;
+ reg = <0x580000 0x14000>;
+ clock-names = "bus_clk", "bus_a_clk";
+ clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
+ <&rpmcc RPM_SMD_SNOC_A_CLK>;
+ };
+
+
+= interconnect consumers =
+
+The interconnect consumers are device nodes which dynamically express their
+bandwidth requirements along interconnect paths they are connected to. There
+can be multiple interconnect providers on a SoC and the consumer may consume
+multiple paths from different providers depending on use case and the
+components it has to interact with.
+
+Required properties:
+interconnects : Pairs of phandles and interconnect provider specifier to denote
+ the edge source and destination ports of the interconnect path.
+
+Optional properties:
+interconnect-names : List of interconnect path name strings sorted in the same
+ order as the interconnects property. Consumers drivers will use
+ interconnect-names to match interconnect paths with interconnect
+ specifier pairs.
+
+Example:
+
+ sdhci@7864000 {
+ ...
+ interconnects = <&pnoc MASTER_SDCC_1 &bimc SLAVE_EBI_CH0>;
+ interconnect-names = "sdhc-mem";
+ };
diff --git a/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt b/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt
new file mode 100644
index 000000000000..5c4f1d911630
--- /dev/null
+++ b/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt
@@ -0,0 +1,24 @@
+Qualcomm SDM845 Network-On-Chip interconnect driver binding
+-----------------------------------------------------------
+
+SDM845 interconnect providers support system bandwidth requirements through
+RPMh hardware accelerators known as Bus Clock Manager (BCM). The provider is
+able to communicate with the BCM through the Resource State Coordinator (RSC)
+associated with each execution environment. Provider nodes must reside within
+an RPMh device node pertaining to their RSC and each provider maps to a single
+RPMh resource.
+
+Required properties :
+- compatible : shall contain only one of the following:
+ "qcom,sdm845-rsc-hlos"
+- #interconnect-cells : should contain 1
+
+Examples:
+
+apps_rsc: rsc {
+ rsc_hlos: interconnect {
+ compatible = "qcom,sdm845-rsc-hlos";
+ #interconnect-cells = <1>;
+ };
+};
+
diff --git a/Documentation/devicetree/bindings/misc/qcom,fastrpc.txt b/Documentation/devicetree/bindings/misc/qcom,fastrpc.txt
new file mode 100644
index 000000000000..2a1827ab50d2
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/qcom,fastrpc.txt
@@ -0,0 +1,78 @@
+Qualcomm Technologies, Inc. FastRPC Driver
+
+The FastRPC implements an IPC (Inter-Processor Communication)
+mechanism that allows for clients to transparently make remote method
+invocations across DSP and APPS boundaries. This enables developers
+to offload tasks to the DSP and free up the application processor for
+other tasks.
+
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must be "qcom,fastrpc"
+
+- label
+ Usage: required
+ Value type: <string>
+ Definition: should specify the dsp domain name this fastrpc
+ corresponds to. must be one of this: "adsp", "mdsp", "sdsp", "cdsp"
+
+- #address-cells
+ Usage: required
+ Value type: <u32>
+ Definition: Must be 1
+
+- #size-cells
+ Usage: required
+ Value type: <u32>
+ Definition: Must be 0
+
+= COMPUTE BANKS
+Each subnode of the Fastrpc represents compute context banks available
+on the dsp.
+- All Compute context banks MUST contain the following properties:
+
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must be "qcom,fastrpc-compute-cb"
+
+- reg
+ Usage: required
+ Value type: <u32>
+ Definition: Context Bank ID.
+
+- qcom,nsessions:
+ Usage: Optional
+ Value type: <u32>
+ Defination: A value indicating how many sessions can share this
+ context bank. Defaults to 1 when this property
+ is not specified.
+
+Example:
+
+adsp-pil {
+ compatible = "qcom,msm8996-adsp-pil";
+ ...
+ smd-edge {
+ label = "lpass";
+ fastrpc {
+ compatible = "qcom,fastrpc";
+ qcom,smd-channels = "fastrpcsmd-apps-dsp";
+ label = "adsp";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cb@1 {
+ compatible = "qcom,fastrpc-compute-cb";
+ reg = <1>;
+ };
+
+ cb@2 {
+ compatible = "qcom,fastrpc-compute-cb";
+ reg = <2>;
+ };
+ ...
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt
index 792bc5fafeb9..7a999a135e56 100644
--- a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt
+++ b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt
@@ -1,7 +1,7 @@
Freescale i.MX6 On-Chip OTP Controller (OCOTP) device tree bindings
This binding represents the on-chip eFuse OTP controller found on
-i.MX6Q/D, i.MX6DL/S, i.MX6SL, i.MX6SX, i.MX6UL and i.MX6SLL SoCs.
+i.MX6Q/D, i.MX6DL/S, i.MX6SL, i.MX6SX, i.MX6UL, i.MX6ULL/ULZ and i.MX6SLL SoCs.
Required properties:
- compatible: should be one of
@@ -9,8 +9,10 @@ Required properties:
"fsl,imx6sl-ocotp" (i.MX6SL), or
"fsl,imx6sx-ocotp" (i.MX6SX),
"fsl,imx6ul-ocotp" (i.MX6UL),
+ "fsl,imx6ull-ocotp" (i.MX6ULL/ULZ),
"fsl,imx7d-ocotp" (i.MX7D/S),
"fsl,imx6sll-ocotp" (i.MX6SLL),
+ "fsl,imx7ulp-ocotp" (i.MX7ULP),
followed by "syscon".
- #address-cells : Should be 1
- #size-cells : Should be 1
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 8f574c778290..542bbf304f13 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -154,6 +154,7 @@ geniatech Geniatech, Inc.
giantec Giantec Semiconductor, Inc.
giantplus Giantplus Technology Co., Ltd.
globalscale Globalscale Technologies, Inc.
+globaltop GlobalTop Technology, Inc.
gmt Global Mixed-mode Technology, Inc.
goodix Shenzhen Huiding Technology Co., Ltd.
google Google, Inc.