summaryrefslogtreecommitdiffstats
path: root/arch/avr32/boards/atstk1000/atstk1002.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/avr32/boards/atstk1000/atstk1002.c')
-rw-r--r--arch/avr32/boards/atstk1000/atstk1002.c78
1 files changed, 76 insertions, 2 deletions
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index e11659b732fa..14dc5a143695 100644
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -1,7 +1,7 @@
/*
- * ATSTK1002 daughterboard-specific init code
+ * ATSTK1002/ATSTK1006 daughterboard-specific init code
*
- * Copyright (C) 2005-2006 Atmel Corporation
+ * Copyright (C) 2005-2007 Atmel Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -35,6 +35,74 @@ unsigned long at32_board_osc_rates[3] = {
[2] = 12000000, /* 12 MHz on osc1 */
};
+/*
+ * The ATSTK1006 daughterboard is very similar to the ATSTK1002. Both
+ * have the AT32AP7000 chip on board; the difference is that the
+ * STK1006 has 128 MB SDRAM (the STK1002 uses the 8 MB SDRAM chip on
+ * the STK1000 motherboard) and 256 MB NAND flash (the STK1002 has
+ * none.)
+ *
+ * The RAM difference is handled by the boot loader, so the only
+ * difference we end up handling here is the NAND flash.
+ */
+#ifdef CONFIG_BOARD_ATSTK1006
+#include <linux/mtd/partitions.h>
+#include <asm/arch/smc.h>
+
+static struct smc_timing nand_timing __initdata = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 10,
+ .ncs_write_setup = 0,
+ .nwe_setup = 10,
+
+ .ncs_read_pulse = 30,
+ .nrd_pulse = 15,
+ .ncs_write_pulse = 30,
+ .nwe_pulse = 15,
+
+ .read_cycle = 30,
+ .write_cycle = 30,
+
+ .ncs_read_recover = 0,
+ .nrd_recover = 15,
+ .ncs_write_recover = 0,
+ /* WE# high -> RE# low min 60 ns */
+ .nwe_recover = 50,
+};
+
+static struct smc_config nand_config __initdata = {
+ .bus_width = 1,
+ .nrd_controlled = 1,
+ .nwe_controlled = 1,
+ .nwait_mode = 0,
+ .byte_write = 0,
+ .tdf_cycles = 2,
+ .tdf_mode = 0,
+};
+
+static struct mtd_partition nand_partitions[] = {
+ {
+ .name = "main",
+ .offset = 0x00000000,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct mtd_partition *nand_part_info(int size, int *num_partitions)
+{
+ *num_partitions = ARRAY_SIZE(nand_partitions);
+ return nand_partitions;
+}
+
+struct atmel_nand_data atstk1006_nand_data __initdata = {
+ .cle = 21,
+ .ale = 22,
+ .rdy_pin = GPIO_PIN_PB(30),
+ .enable_pin = GPIO_PIN_PB(29),
+ .partition_info = nand_part_info,
+};
+#endif
+
struct eth_addr {
u8 addr[6];
};
@@ -218,6 +286,12 @@ static int __init atstk1002_init(void)
at32_add_system_devices();
+#ifdef CONFIG_BOARD_ATSTK1006
+ smc_set_timing(&nand_config, &nand_timing);
+ smc_set_configuration(3, &nand_config);
+ at32_add_device_nand(0, &atstk1006_nand_data);
+#endif
+
#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
at32_add_device_usart(1);
#else