diff options
Diffstat (limited to 'arch/blackfin/include/asm/bfin_serial.h')
| -rw-r--r-- | arch/blackfin/include/asm/bfin_serial.h | 263 |
1 files changed, 263 insertions, 0 deletions
diff --git a/arch/blackfin/include/asm/bfin_serial.h b/arch/blackfin/include/asm/bfin_serial.h new file mode 100644 index 000000000000..e9510eab5e22 --- /dev/null +++ b/arch/blackfin/include/asm/bfin_serial.h @@ -0,0 +1,263 @@ +/* + * bfin_serial.h - Blackfin UART/Serial definitions + * + * Copyright 2006-2010 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __BFIN_ASM_SERIAL_H__ +#define __BFIN_ASM_SERIAL_H__ + +#include <linux/serial_core.h> +#include <mach/anomaly.h> +#include <mach/bfin_serial.h> + +struct circ_buf; +struct timer_list; +struct work_struct; + +struct bfin_serial_port { + struct uart_port port; + unsigned int old_status; + int status_irq; +#ifndef BFIN_UART_BF54X_STYLE + unsigned int lsr; +#endif +#ifdef CONFIG_SERIAL_BFIN_DMA + int tx_done; + int tx_count; + struct circ_buf rx_dma_buf; + struct timer_list rx_dma_timer; + int rx_dma_nrows; + unsigned int tx_dma_channel; + unsigned int rx_dma_channel; + struct work_struct tx_dma_workqueue; +#elif ANOMALY_05000363 + unsigned int anomaly_threshold; +#endif +#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS + int scts; +#endif +#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \ + defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS) + int cts_pin; + int rts_pin; +#endif +}; + +/* UART_LCR Masks */ +#define WLS(x) (((x)-5) & 0x03) /* Word Length Select */ +#define STB 0x04 /* Stop Bits */ +#define PEN 0x08 /* Parity Enable */ +#define EPS 0x10 /* Even Parity Select */ +#define STP 0x20 /* Stick Parity */ +#define SB 0x40 /* Set Break */ +#define DLAB 0x80 /* Divisor Latch Access */ + +/* UART_LSR Masks */ +#define DR 0x01 /* Data Ready */ +#define OE 0x02 /* Overrun Error */ +#define PE 0x04 /* Parity Error */ +#define FE 0x08 /* Framing Error */ +#define BI 0x10 /* Break Interrupt */ +#define THRE 0x20 /* THR Empty */ +#define TEMT 0x40 /* TSR and UART_THR Empty */ +#define TFI 0x80 /* Transmission Finished Indicator */ + +/* UART_IER Masks */ +#define ERBFI 0x01 /* Enable Receive Buffer Full Interrupt */ +#define ETBEI 0x02 /* Enable Transmit Buffer Empty Interrupt */ +#define ELSI 0x04 /* Enable RX Status Interrupt */ +#define EDSSI 0x08 /* Enable Modem Status Interrupt */ +#define EDTPTI 0x10 /* Enable DMA Transmit PIRQ Interrupt */ +#define ETFI 0x20 /* Enable Transmission Finished Interrupt */ +#define ERFCI 0x40 /* Enable Receive FIFO Count Interrupt */ + +/* UART_MCR Masks */ +#define XOFF 0x01 /* Transmitter Off */ +#define MRTS 0x02 /* Manual Request To Send */ +#define RFIT 0x04 /* Receive FIFO IRQ Threshold */ +#define RFRT 0x08 /* Receive FIFO RTS Threshold */ +#define LOOP_ENA 0x10 /* Loopback Mode Enable */ +#define FCPOL 0x20 /* Flow Control Pin Polarity */ +#define ARTS 0x40 /* Automatic Request To Send */ +#define ACTS 0x80 /* Automatic Clear To Send */ + +/* UART_MSR Masks */ +#define SCTS 0x01 /* Sticky CTS */ +#define CTS 0x10 /* Clear To Send */ +#define RFCS 0x20 /* Receive FIFO Count Status */ + +/* UART_GCTL Masks */ +#define UCEN 0x01 /* Enable UARTx Clocks */ +#define IREN 0x02 /* Enable IrDA Mode */ +#define TPOLC 0x04 /* IrDA TX Polarity Change */ +#define RPOLC 0x08 /* IrDA RX Polarity Change */ +#define FPE 0x10 /* Force Parity Error On Transmit */ +#define FFE 0x20 /* Force Framing Error On Transmit */ + +#ifdef BFIN_UART_BF54X_STYLE +# define OFFSET_DLL 0x00 /* Divisor Latch (Low-Byte) */ +# define OFFSET_DLH 0x04 /* Divisor Latch (High-Byte) */ +# define OFFSET_GCTL 0x08 /* Global Control Register */ +# define OFFSET_LCR 0x0C /* Line Control Register */ +# define OFFSET_MCR 0x10 /* Modem Control Register */ +# define OFFSET_LSR 0x14 /* Line Status Register */ +# define OFFSET_MSR 0x18 /* Modem Status Register */ +# define OFFSET_SCR 0x1C /* SCR Scratch Register */ +# define OFFSET_IER_SET 0x20 /* Set Interrupt Enable Register */ +# define OFFSET_IER_CLEAR 0x24 /* Clear Interrupt Enable Register */ +# define OFFSET_THR 0x28 /* Transmit Holding register */ +# define OFFSET_RBR 0x2C /* Receive Buffer register */ +#else /* BF533 style */ +# define OFFSET_THR 0x00 /* Transmit Holding register */ +# define OFFSET_RBR 0x00 /* Receive Buffer register */ +# define OFFSET_DLL 0x00 /* Divisor Latch (Low-Byte) */ +# define OFFSET_DLH 0x04 /* Divisor Latch (High-Byte) */ +# define OFFSET_IER 0x04 /* Interrupt Enable Register */ +# define OFFSET_IIR 0x08 /* Interrupt Identification Register */ +# define OFFSET_LCR 0x0C /* Line Control Register */ +# define OFFSET_MCR 0x10 /* Modem Control Register */ +# define OFFSET_LSR 0x14 /* Line Status Register */ +# define OFFSET_MSR 0x18 /* Modem Status Register */ +# define OFFSET_SCR 0x1C /* SCR Scratch Register */ +# define OFFSET_GCTL 0x24 /* Global Control Register */ +/* code should not need IIR, so force build error if they use it */ +# undef OFFSET_IIR +#endif + +/* + * All Blackfin system MMRs are padded to 32bits even if the register + * itself is only 16bits. So use a helper macro to streamline this. + */ +#define __BFP(m) u16 m; u16 __pad_##m +struct bfin_uart_regs { +#ifdef BFIN_UART_BF54X_STYLE + __BFP(dll); + __BFP(dlh); + __BFP(gctl); + __BFP(lcr); + __BFP(mcr); + __BFP(lsr); + __BFP(msr); + __BFP(scr); + __BFP(ier_set); + __BFP(ier_clear); + __BFP(thr); + __BFP(rbr); +#else + union { + u16 dll; + u16 thr; + const u16 rbr; + }; + const u16 __pad0; + union { + u16 dlh; + u16 ier; + }; + const u16 __pad1; + const __BFP(iir); + __BFP(lcr); + __BFP(mcr); + __BFP(lsr); + __BFP(msr); + __BFP(scr); + const u32 __pad2; + __BFP(gctl); +#endif +}; +#undef __BFP + +#ifndef port_membase +# define port_membase(p) (((struct bfin_serial_port *)(p))->port.membase) +#endif + +#define UART_GET_CHAR(p) bfin_read16(port_membase(p) + OFFSET_RBR) +#define UART_GET_DLL(p) bfin_read16(port_membase(p) + OFFSET_DLL) +#define UART_GET_DLH(p) bfin_read16(port_membase(p) + OFFSET_DLH) +#define UART_GET_GCTL(p) bfin_read16(port_membase(p) + OFFSET_GCTL) +#define UART_GET_LCR(p) bfin_read16(port_membase(p) + OFFSET_LCR) +#define UART_GET_MCR(p) bfin_read16(port_membase(p) + OFFSET_MCR) +#define UART_GET_MSR(p) bfin_read16(port_membase(p) + OFFSET_MSR) + +#define UART_PUT_CHAR(p, v) bfin_write16(port_membase(p) + OFFSET_THR, v) +#define UART_PUT_DLL(p, v) bfin_write16(port_membase(p) + OFFSET_DLL, v) +#define UART_PUT_DLH(p, v) bfin_write16(port_membase(p) + OFFSET_DLH, v) +#define UART_PUT_GCTL(p, v) bfin_write16(port_membase(p) + OFFSET_GCTL, v) +#define UART_PUT_LCR(p, v) bfin_write16(port_membase(p) + OFFSET_LCR, v) +#define UART_PUT_MCR(p, v) bfin_write16(port_membase(p) + OFFSET_MCR, v) + +#ifdef BFIN_UART_BF54X_STYLE + +#define UART_CLEAR_IER(p, v) bfin_write16(port_membase(p) + OFFSET_IER_CLEAR, v) +#define UART_GET_IER(p) bfin_read16(port_membase(p) + OFFSET_IER_SET) +#define UART_SET_IER(p, v) bfin_write16(port_membase(p) + OFFSET_IER_SET, v) + +#define UART_CLEAR_DLAB(p) /* MMRs not muxed on BF54x */ +#define UART_SET_DLAB(p) /* MMRs not muxed on BF54x */ + +#define UART_CLEAR_LSR(p) bfin_write16(port_membase(p) + OFFSET_LSR, -1) +#define UART_GET_LSR(p) bfin_read16(port_membase(p) + OFFSET_LSR) +#define UART_PUT_LSR(p, v) bfin_write16(port_membase(p) + OFFSET_LSR, v) + +/* This handles hard CTS/RTS */ +#define UART_CLEAR_SCTS(p) bfin_write16((port_membase(p) + OFFSET_MSR), SCTS) +#define UART_GET_CTS(x) (UART_GET_MSR(x) & CTS) +#define UART_DISABLE_RTS(x) UART_PUT_MCR(x, UART_GET_MCR(x) & ~(ARTS | MRTS)) +#define UART_ENABLE_RTS(x) UART_PUT_MCR(x, UART_GET_MCR(x) | MRTS | ARTS) +#define UART_ENABLE_INTS(x, v) UART_SET_IER(x, v) +#define UART_DISABLE_INTS(x) UART_CLEAR_IER(x, 0xF) + +#else /* BF533 style */ + +#define UART_CLEAR_IER(p, v) UART_PUT_IER(p, UART_GET_IER(p) & ~(v)) +#define UART_GET_IER(p) bfin_read16(port_membase(p) + OFFSET_IER) +#define UART_PUT_IER(p, v) bfin_write16(port_membase(p) + OFFSET_IER, v) +#define UART_SET_IER(p, v) UART_PUT_IER(p, UART_GET_IER(p) | (v)) + +#define UART_CLEAR_DLAB(p) do { UART_PUT_LCR(p, UART_GET_LCR(p) & ~DLAB); SSYNC(); } while (0) +#define UART_SET_DLAB(p) do { UART_PUT_LCR(p, UART_GET_LCR(p) | DLAB); SSYNC(); } while (0) + +#ifndef put_lsr_cache +# define put_lsr_cache(p, v) (((struct bfin_serial_port *)(p))->lsr = (v)) +#endif +#ifndef get_lsr_cache +# define get_lsr_cache(p) (((struct bfin_serial_port *)(p))->lsr) +#endif + +/* The hardware clears the LSR bits upon read, so we need to cache + * some of the more fun bits in software so they don't get lost + * when checking the LSR in other code paths (TX). + */ +static inline void UART_CLEAR_LSR(void *p) +{ + put_lsr_cache(p, 0); + bfin_write16(port_membase(p) + OFFSET_LSR, -1); +} +static inline unsigned int UART_GET_LSR(void *p) +{ + unsigned int lsr = bfin_read16(port_membase(p) + OFFSET_LSR); + put_lsr_cache(p, get_lsr_cache(p) | (lsr & (BI|FE|PE|OE))); + return lsr | get_lsr_cache(p); +} +static inline void UART_PUT_LSR(void *p, uint16_t val) +{ + put_lsr_cache(p, get_lsr_cache(p) & ~val); +} + +/* This handles soft CTS/RTS */ +#define UART_GET_CTS(x) gpio_get_value((x)->cts_pin) +#define UART_DISABLE_RTS(x) gpio_set_value((x)->rts_pin, 1) +#define UART_ENABLE_RTS(x) gpio_set_value((x)->rts_pin, 0) +#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v) +#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0) + +#endif + +#ifndef BFIN_UART_TX_FIFO_SIZE +# define BFIN_UART_TX_FIFO_SIZE 2 +#endif + +#endif /* __BFIN_ASM_SERIAL_H__ */ |