summaryrefslogtreecommitdiffstats
path: root/drivers/scsi/pas16.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/scsi/pas16.h')
-rw-r--r--drivers/scsi/pas16.h121
1 files changed, 0 insertions, 121 deletions
diff --git a/drivers/scsi/pas16.h b/drivers/scsi/pas16.h
deleted file mode 100644
index 9fe7f33660b4..000000000000
--- a/drivers/scsi/pas16.h
+++ /dev/null
@@ -1,121 +0,0 @@
-/*
- * This driver adapted from Drew Eckhardt's Trantor T128 driver
- *
- * Copyright 1993, Drew Eckhardt
- * Visionary Computing
- * (Unix and Linux consulting and custom programming)
- * drew@colorado.edu
- * +1 (303) 666-5836
- *
- * ( Based on T128 - DISTRIBUTION RELEASE 3. )
- *
- * Modified to work with the Pro Audio Spectrum/Studio 16
- * by John Weidman.
- *
- *
- * For more information, please consult
- *
- * Media Vision
- * (510) 770-8600
- * (800) 348-7116
- */
-
-
-#ifndef PAS16_H
-#define PAS16_H
-
-#define PAS16_DEFAULT_BASE_1 0x388
-#define PAS16_DEFAULT_BASE_2 0x384
-#define PAS16_DEFAULT_BASE_3 0x38c
-#define PAS16_DEFAULT_BASE_4 0x288
-
-#define PAS16_DEFAULT_BOARD_1_IRQ 10
-#define PAS16_DEFAULT_BOARD_2_IRQ 12
-#define PAS16_DEFAULT_BOARD_3_IRQ 14
-#define PAS16_DEFAULT_BOARD_4_IRQ 15
-
-
-/*
- * The Pro Audio Spectrum boards are I/O mapped. They use a Zilog 5380
- * SCSI controller, which is the equivalent of NCR's 5380. "Pseudo-DMA"
- * architecture is used, where a PAL drives the DMA signals on the 5380
- * allowing fast, blind transfers with proper handshaking.
- */
-
-
-/* The Time-out Counter register is used to safe-guard against a stuck
- * bus (in the case of RDY driven handshake) or a stuck byte (if 16-Bit
- * DMA conversion is used). The counter uses a 28.224MHz clock
- * divided by 14 as its clock source. In the case of a stuck byte in
- * the holding register, an interrupt is generated (and mixed with the
- * one with the drive) using the CD-ROM interrupt pointer.
- */
-
-#define P_TIMEOUT_COUNTER_REG 0x4000
-#define P_TC_DISABLE 0x80 /* Set to 0 to enable timeout int. */
- /* Bits D6-D0 contain timeout count */
-
-
-#define P_TIMEOUT_STATUS_REG_OFFSET 0x4001
-#define P_TS_TIM 0x80 /* check timeout status */
- /* Bits D6-D4 N/U */
-#define P_TS_ARM_DRQ_INT 0x08 /* Arm DRQ Int. When set high,
- * the next rising edge will
- * cause a CD-ROM interrupt.
- * When set low, the interrupt
- * will be cleared. There is
- * no status available for
- * this interrupt.
- */
-#define P_TS_ENABLE_TO_ERR_INTERRUPT /* Enable timeout error int. */
-#define P_TS_ENABLE_WAIT /* Enable Wait */
-
-#define P_TS_CT 0x01 /* clear timeout. Note: writing
- * to this register clears the
- * timeout error int. or status
- */
-
-
-/*
- * The data register reads/writes to/from the 5380 in pseudo-DMA mode
- */
-
-#define P_DATA_REG_OFFSET 0x5c00 /* rw */
-
-#define P_STATUS_REG_OFFSET 0x5c01 /* ro */
-#define P_ST_RDY 0x80 /* 5380 DDRQ Status */
-
-#define P_IRQ_STATUS 0x5c03
-#define P_IS_IRQ 0x80 /* DIRQ status */
-
-#define PCB_CONFIG 0x803
-#define MASTER_ADDRESS_PTR 0x9a01 /* Fixed position - no relo */
-#define SYS_CONFIG_4 0x8003
-#define WAIT_STATE 0xbc00
-#define OPERATION_MODE_1 0xec03
-#define IO_CONFIG_3 0xf002
-
-#define NCR5380_implementation_fields /* none */
-
-#define PAS16_io_port(reg) (instance->io_port + pas16_offset[(reg)])
-
-#define NCR5380_read(reg) ( inb(PAS16_io_port(reg)) )
-#define NCR5380_write(reg, value) ( outb((value),PAS16_io_port(reg)) )
-
-#define NCR5380_dma_xfer_len(instance, cmd, phase) (cmd->transfersize)
-#define NCR5380_dma_recv_setup pas16_pread
-#define NCR5380_dma_send_setup pas16_pwrite
-#define NCR5380_dma_residual(instance) (0)
-
-#define NCR5380_intr pas16_intr
-#define NCR5380_queue_command pas16_queue_command
-#define NCR5380_abort pas16_abort
-#define NCR5380_bus_reset pas16_bus_reset
-#define NCR5380_info pas16_info
-
-/* 15 14 12 10 7 5 3
- 1101 0100 1010 1000 */
-
-#define PAS16_IRQS 0xd4a8
-
-#endif /* PAS16_H */