diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/staging/rdma/hfi1/firmware.c | 57 |
1 files changed, 44 insertions, 13 deletions
diff --git a/drivers/staging/rdma/hfi1/firmware.c b/drivers/staging/rdma/hfi1/firmware.c index 4ba524b82edd..0b23e3eaf574 100644 --- a/drivers/staging/rdma/hfi1/firmware.c +++ b/drivers/staging/rdma/hfi1/firmware.c @@ -233,6 +233,8 @@ static const u8 all_pcie_serdes_broadcast = 0xe0; /* forwards */ static void dispose_one_firmware(struct firmware_details *fdet); +static int load_fabric_serdes_firmware(struct hfi1_devdata *dd, + struct firmware_details *fdet); /* * Read a single 64-bit value from 8051 data memory. @@ -1092,27 +1094,56 @@ static void turn_off_spicos(struct hfi1_devdata *dd, int flags) } /* - * Reset all of the fabric serdes for our HFI. + * Reset all of the fabric serdes for this HFI in preparation to take the + * link to Polling. + * + * To do a reset, we need to write to to the serdes registers. Unfortunately, + * the fabric serdes download to the other HFI on the ASIC will have turned + * off the firmware validation on this HFI. This means we can't write to the + * registers to reset the serdes. Work around this by performing a complete + * re-download and validation of the fabric serdes firmware. This, as a + * by-product, will reset the serdes. NOTE: the re-download requires that + * the 8051 be in the Offline state. I.e. not actively trying to use the + * serdes. This routine is called at the point where the link is Offline and + * is getting ready to go to Polling. */ void fabric_serdes_reset(struct hfi1_devdata *dd) { - u8 ra; - - if (dd->icode != ICODE_RTL_SILICON) /* only for RTL */ + if (!fw_fabric_serdes_load) return; - ra = fabric_serdes_broadcast[dd->hfi1_id]; + if (is_ax(dd)) { + /* A0 serdes do not work with a re-download */ + u8 ra = fabric_serdes_broadcast[dd->hfi1_id]; + + acquire_hw_mutex(dd); + set_sbus_fast_mode(dd); + /* place SerDes in reset and disable SPICO */ + sbus_request(dd, ra, 0x07, WRITE_SBUS_RECEIVER, 0x00000011); + /* wait 100 refclk cycles @ 156.25MHz => 640ns */ + udelay(1); + /* remove SerDes reset */ + sbus_request(dd, ra, 0x07, WRITE_SBUS_RECEIVER, 0x00000010); + /* turn SPICO enable on */ + sbus_request(dd, ra, 0x07, WRITE_SBUS_RECEIVER, 0x00000002); + clear_sbus_fast_mode(dd); + release_hw_mutex(dd); + return; + } acquire_hw_mutex(dd); set_sbus_fast_mode(dd); - /* place SerDes in reset and disable SPICO */ - sbus_request(dd, ra, 0x07, WRITE_SBUS_RECEIVER, 0x00000011); - /* wait 100 refclk cycles @ 156.25MHz => 640ns */ - udelay(1); - /* remove SerDes reset */ - sbus_request(dd, ra, 0x07, WRITE_SBUS_RECEIVER, 0x00000010); - /* turn SPICO enable on */ - sbus_request(dd, ra, 0x07, WRITE_SBUS_RECEIVER, 0x00000002); + + turn_off_spicos(dd, SPICO_FABRIC); + /* + * No need for firmware retry - what to download has already been + * decided. + * No need to pay attention to the load return - the only failure + * is a validation failure, which has already been checked by the + * initial download. + */ + (void)load_fabric_serdes_firmware(dd, &fw_fabric); + clear_sbus_fast_mode(dd); release_hw_mutex(dd); } |