summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-kirkwood/Makefile
Commit message (Collapse)AuthorAgeFilesLines
* ARM: Kirkwood: Remove mach-kirkwoodAndrew Lunn2014-07-141-14/+0Star
| | | | | | | | | Now that all boards have been converted to DT and all the support code lives in mach-mvebu, we can remove mach-kirkwood. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Link: https://lkml.kernel.org/r/1405028192-9623-2-git-send-email-andrew@lunn.ch Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: Separate board-dt from common and pcie code.Andrew Lunn2014-02-221-2/+1Star
| | | | | | | | | | | | In order to be able to move DT support into mach-mvebu, the DT code needs to be cleanly separated from common and pcie code. Import the needed bits of these files into board-dt.c. The "common" code then becomes purely legacy, supporting non-DT boards, so reflect this in the Makefile targets. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: Convert mv88f6281gtw_ge switch setup to DTAndrew Lunn2014-02-221-1/+0Star
| | | | | | | | | | | | The mv88f6281gtw_ge has a ethernet switch connected to the ethernet port of the SoC. Convert the platform device instantiation to a DT instantiation. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Arnd Bergmann <arnd@arndb.de> Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: florian@openwrt.org Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: Add standby supportEzequiel Garcia2013-10-081-0/+2
| | | | | | | | | | | | | Implements standby support for Kirkwood SoC. When the SoC enters standby state the memory PM units are disabled, the DDR is set in self-refresh mode, and the CPU is set in WFI. At this point there's no clock gating, as that is considered each driver's task. Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform codeJamie Lentin2013-08-121-1/+0Star
| | | | | | | | | | No platform code left now, so remove all references to it. The reset gpio code didn't work to begin with, it will be replaced with a DT node at a future date. -jc Signed-off-by: Jamie Lentin <jm@lentin.co.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: convert the mv88f6281gtw_ge board to DTThomas Petazzoni2013-08-061-1/+1
| | | | | | | | | | | This commit converts the mv88f6281gtw_ge Kirkwood board to use a Device Tree representation, except for the Ethernet devices and the DSA switch. Even though the mv643xx_eth driver has a DT binding, converting this board to use it is for now left on the side because it doesn't use a simple PHY, but a DSA switch instead. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: remove LaCie boards that are supported through DTThomas Petazzoni2013-08-061-3/+0Star
| | | | | | | | | The "LaCie Internet Space v2 NAS Board", "LaCie Network Space Max v2 NAS Board" and "LaCie Network Space v2 NAS Board" boards are all supported through the Device Tree. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: remove support for legacy booting of SheevaplugThomas Petazzoni2013-08-061-2/+0Star
| | | | | | | | | The Kirkwood Sheevaplug platform has already been converted to the Device Tree, so we can remove the legacy booting option for this platform. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: remove support for legacy booting of GuruplugThomas Petazzoni2013-08-061-1/+0Star
| | | | | | | | | The Kirkwood Guruplug platform has already been converted to the Device Tree, so we can remove the legacy booting option for this platform. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: remove support for legacy booting of DockstarThomas Petazzoni2013-08-061-1/+0Star
| | | | | | | | | The Kirkwood Dockstar platform has already been converted to the Device Tree, so we can remove the legacy booting option for this platform. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: convert to DT irqchip and clocksourceSebastian Hesselbarth2013-07-251-2/+2
| | | | | | | | | | | With recent support for true irqchip and clocksource drivers for Orion SoCs, now make use of it on DT enabled Kirkwood boards. This also introduces a new Kconfig option for legacy (non-DT) Kirkwood where old code is moved out to and polishes DT board file a little bit. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: remove redundant DT board filesSebastian Hesselbarth2013-07-251-22/+0Star
| | | | | | | | | With DT support for mv643xx_eth board specific init for some boards now is unneccessary. Remove those board files, Kconfig entries, and corresponding entries in kirkwood_defconfig. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* Merge tag 'boards-for-linus' of ↵Linus Torvalds2013-07-021-0/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC board specific changes from Arnd Bergmann: "These are 18 branches on 9 platforms with board specific changes, mostly for defconfig files, but nothing really exciting in here. Since the shmobile platform still uses board files for some of the newer machines, we get a few changes there as the result of drivers getting enabled for those boards. This causes some conflicts with contents getting added from multiple branches in sh-mobile specific files. Renesas is putting a lot of work into migrating to device-tree based setup, which will make all those files obsolete in the future and avoid both the conflicts and the need to have these files in the first place." * tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits) arm: multi_v7_defconfig: Enable initrd/initramfs support arm: multi_v7_defconfig: Enable Zynq UART driver ARM: omap2plus_defconfig: enable USB_PHY and NOP_USB_XCEIV ARM: OMAP1: nokia770: enable Tahvo ARM: OMAP3EVM: Marking omap3_evm_display_init() with CONFIG_BROKEN arm: omap: board-overo: reset GPIO for SMSC911x ARM: shmobile: BOCK-W: change Ether device name ARM: ux500: board-mop500: remove unused pin modes ARM: shmobile: bockw: add MMCIF support ARM: shmobile: bockw: add SPI FLASH support ARM: shmobile: bockw: add I2C device support ARM: shmobile: BOCK-W: add Ether support ARM: tegra: defconfig updates ARM: shmobile: bockw defconfig: add MMCIF support ARM: shmobile: bockw defconfig: add M25P80 support ARM: shmobile: bockw defconfig: add RTC RX8581 support ARM: shmobile: marzen: keep local function as static ARM: shmobile: bockw: add SDHI0 support ARM: shmobile: marzen: Use INTC External IRQ pin driver for SMSC ARM: shmobile: lager: support GPIO switches ...
| * ARM: Kirkwood: add DT support for Sheevaplug and Sheevaplug eSATASimon Baatz2013-05-151-0/+1
| | | | | | | | | | Signed-off-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* | arm: kirkwood: convert db-88f6281/db-88f6282 to the Device TreeThomas Petazzoni2013-05-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit converts the Marvell DB-88F6281/DB-88F6282 board to the Device Tree. In fact, the code was supporting two different boards: one with the 6281 SoC variant, and one with the 6282 SoC variant. The difference between the two being that the 6281 has one PCIe interface, and the 6282 has two PCIe interfaces. In order to handle that with the Device Tree, we create a 'kirkwood-db.dtsi' file that contains the definitions common to both boards, and 'kirkwood-db-88f6281.dts' and 'kirkwood-db-88f6282.dts' for the definitions specific to each board. This is similar to what is done for the QNAP TS219 Kirkwood platform. We have kept one single Kconfig option, just like it was before. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* | arm: kirkwood: convert ZyXEL NSA310 to use DT for the PCIe interfaceThomas Petazzoni2013-05-271-1/+0Star
|/ | | | | | | | | | | | | Now that the PCIe mvebu driver is usable on Kirkwood, use it instead of the legacy PCIe code, since it allows to describe the PCIe interfaces in the Device Tree. Since it was the only device left that prevented this platform to use the Device Tree only, we remove the board-nsa310.c file and the related Kconfig/Makefile bits. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* Merge tag 'soc-for-linus-3' of ↵Linus Torvalds2013-05-071-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC platform updates (part 3) from Arnd Bergmann: "This is the third and smallest of the SoC specific updates. Changes include: - SMP support for the Xilinx zynq platform - Smaller imx changes - LPAE support for mvebu - Moving the orion5x, kirkwood, dove and mvebu platforms to a common "mbus" driver for their internal devices. It would be good to get feedback on the location of the "mbus" driver. Since this is used on multiple platforms may potentially get shared with other architectures (powerpc and arm64), it was moved to drivers/bus/. We expect other similar drivers to get moved to the same place in order to avoid creating more top-level directories under drivers/ or cluttering up the messy drivers/misc/ even more." * tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits) ARM: imx: reset_controller may be disabled ARM: mvebu: Align the internal registers virtual base to support LPAE ARM: mvebu: Limit the DMA zone when LPAE is selected arm: plat-orion: remove addr-map code arm: mach-mv78xx0: convert to use the mvebu-mbus driver arm: mach-orion5x: convert to use mvebu-mbus driver arm: mach-dove: convert to use mvebu-mbus driver arm: mach-kirkwood: convert to use mvebu-mbus driver arm: mach-mvebu: convert to use mvebu-mbus driver ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock ARM i.MX53: tve_di clock is not part of the CCM, but of TVE ARM i.MX53: make tve_ext_sel propagate rate change to PLL ARM i.MX53: Remove unused tve_gate clkdev entry ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree ARM: i.MX5: Add PATA and SRTC clocks ARM: imx: do not bring up unavailable cores ARM: imx: add initial imx6dl support ARM: imx1: mm: add call to mxc_device_init ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS ...
| * arm: mach-kirkwood: convert to use mvebu-mbus driverThomas Petazzoni2013-04-151-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit migrates the mach-kirkwood platforms to use the mvebu-mbus driver and therefore removes the Kirkwood-specific addr-map code. The kirkwood_init_early() function is now responsible for initializing the mvebu-mbus driver by calling mvebu_mbus_init(). The address decoding windows are now registered in the kirkwood_setup_wins() function. It is worth noting that the four PCIe address decoding windows will ultimately no longer have to be registered here: it will be done automatically by the PCIe driver once Kirkwood has been migrated to use the upcoming mvebu PCIe driver. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* | ARM: Kirkwood: DT board setup for CloudBoxSimon Guinot2013-04-101-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds DT board setup for the LaCie NAS CloudBox. The CloudBox is a low cost NAS based on the Network Space v2. Chipset list: - CPU MARVELL 88F6702 1Ghz - SDRAM memory: 256MB DDR2-800 (2x128MB x8) 400Mhz - 1 Ethernet Gigabit port (PHY MARVELL 88E1318) - SPI flash, NOR 512KB - 1 push button - 2 LEDs (red and blue) There is no EEPROM and no USB ports embedded. Note that this board must not be confused with the Network Space Mini v2 which is embedded in a previous LaCie product also named CloudBox. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* | ARM: Kirkwood: sort board entries by ASCII-code orderSimon Guinot2013-04-101-20/+20
| | | | | | | | | | | | | | | | | | This patch sorts board entries in files Kconfig, Makefile and kirkwood_defconfig by ASCII-code order. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* | ARM: kirkwood: Add support for NETGEAR ReadyNAS Duo v2 using DTArnaud Ebalard2013-03-281-0/+1
|/ | | | | | | | | | | | Add support for NETGEAR ReadyNAS Duo v2 (Hardware specs available here: http://natisbad.org/NAS/). Almost everything is supported via provided .dts. A board-readynas.c file is nonetheless required for device not only converted to DT (Gbit controller). Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Tested-By: Arnaud Ebalard <arno@natisbad.org> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: convert Guruplug Server Plus to use the device treeWilly Tarreau2013-02-281-0/+1
| | | | | | | | | | Add a device tree entry for the Guruplug Server Plus board. This port was based both on the work done on the dreamplug and the dockstar. It builds, boots and works on my Guruplug Server Plus. Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* cpuidle: kirkwood: Move out of mach directoryAndrew Lunn2013-01-311-1/+0Star
| | | | | | | | Move the Kirkwood cpuidle driver out of arch/arm/mach-kirkwood and into drivers/cpuidle. Convert the driver into a platform driver. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: Add Plat'Home OpenBlocks A6 supportNobuhiro Iwamatsu2012-11-221-0/+1
| | | | | | | | | Add support for Plat'Home OpenBlocks A6 using the device tree where possible. This commit supports SATA, USB, ether and serial console. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: Add support for the MPL CEC4Stefan Peter2012-11-211-0/+1
| | | | | Signed-off-by: Stefan Peter <s.peter@mpl.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* arm: kirkwood: add support for ZyXEL NSA310Tero Jaasko2012-11-211-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hello, Andrew > > +#define NSA310_GPIO_LED_ESATA_GREEN 12 > > <..> > > +#define NSA310_GPIO_POWER_OFF 48 > > It looks like most of these are not used. Please remove them. True. Fixed. > > +static struct mtd_partition nsa310_mtd_parts[] = { > > + { > > + .name = "uboot", > > + .offset = 0, > > + .size = 0x100000, > > + .mask_flags = MTD_WRITEABLE, > > + }, { > > <..> > You should be able to put all that into DT. Take a look at Correct. I did the conversion and tested that the partitions can be read with dd and produce exactly the same data before and after conversion. So, the partition offsets at least should be fine. > > +static struct i2c_board_info __initdata nsa310_i2c_info[] = { > > + { I2C_BOARD_INFO("adt7476", 0x2e) }, > > +}; > > You can also do this in DT as well. kirkwood-ts219.dtsi has > > i2c@11000 { > status = "okay"; > clock-frequency = <400000>; Ok, I did convert the i2c definition to use the devicetree. The adt7476 device itself is not at reach of device tree, AFAIK and requires more work at there? Thanks for your valuable comments. Following is a new patch that should address the problems and mistakes you pointed and also some of the pointed by Jason Cooper. The nand and i2c are now defined at DT and I also removed the pointless defines and ARM_APPENDED_DTB. It is based against the Linus' official 3.6 version. Best regards, Tero Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: Kirkwood: new board USI TopkickJason Cooper2012-11-211-0/+1
| | | | | | | | | | | | | | This is a new kirkwood box made by Universal Scientific Industrial, Inc. The product description is here: http://www.usish.com/english/products_topkick1281p2.php It is very similar to the dreamplug and other plug devices, with the exception that it has room for a 2.5" SATA HDD internally. Signed-off-by: Jason Cooper <jason@lakedaemon.net> Acked-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
* ARM: kirkwood: DT board setup for Network Space Mini v2Simon Guinot2012-11-211-0/+1
| | | | | | | | | | | | | This patch adds DT board setup for the LaCie NAS Network Space Mini v2 (aka SafeBox). The hardware characteristics are very close to those of the Network Space Lite v2. The main difference are: - A GPIO fan which is only available on the NS2 Mini. - A single USB host port is wired on the NS2 Mini. The NS2 Lite provides an additional dual-mode USB port (host/device). Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: DT board setup for Network Space Lite v2Simon Guinot2012-11-211-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds DT board setup for the LaCie NAS Network Space Lite v2. This board is derived from the Network Space v2 and a lot of hardware characteristics are shared. - CPU: Marvell 88F6192 800Mhz - SDRAM memory: 128MB DDR2 200Mhz - 1 SATA port: internal - Gigabit ethernet: PHY Marvell 88E1318 - Flash memory: SPI NOR 512KB (Macronix MX25L4005A) - i2c EEPROM: 512 bytes (24C04 type) - 2 USB2 ports: host and host/device - 1 push button - 1 SATA LED (bi-color, blue and red) Note that the SATA LED is not compatible with the driver leds-ns2. The LED behaviour ("on", "off" or "SATA activity blink") is controlled via a single MPP (21). Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: DT board setup for Network Space v2 and parentsSimon Guinot2012-11-211-0/+3
| | | | | | | | | | This patch adds DT board setup for LaCie Network Space v2 and parents, based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2 (Max) and Internet Space v2. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: initial DTS support for km_kirkwoodValentin Longchamp2012-09-211-0/+1
| | | | | | | | | | | | | | | | This is a first attempt to support the km_kirkwood reference design with a device tree. This km_kirkwood design is present in many Keymile products. It is based on the Marvell Bobcat SOC which integrates a Kirkwood CPU next to a big L2 Ethernet Switch. The Kirkwood in the SOC is very similar to the "normal" one, but there are a few differences. This initial support is minimal: the kernel can boot with network (ge0), serial port and NAND functional. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Holger Brunck <holger.brunck@keymile.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: DT board setup for Seagate FreeAgent DockstarSebastian Hesselbarth2012-09-211-0/+1
| | | | | | | | This add a DT compatible board specific setup for the Seagate FreeAgent Dockstar. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: Kirkwood: Iomega ix2-200 DT supportAlan M Butler2012-09-211-0/+1
| | | | | | | | | | | | | | | | Add support for the Iomega ix2-200. Led's and buttons working as of kernel 3.6-rc2 the 3 lines in the network interface do seem to be required as removing either causes the network card to not be able to reach the network (at least on my device). Product page: http://go.iomega.com/en/products/network-storage-desktop/storcenter-network-storage-solution/network-hard-drive-ix2-200-cloud/?partner=4735#tech_specsItem_tab Signed-off-by: Alan M Butler <alanbutty12@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: Add LS-XHL and LS-CHLv2 supportMichael Walle2012-07-271-0/+1
| | | | | | | | Add support for Buffalo Linkstation LS-XHL and LS-CHLv2 using the device tree where possible. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
* ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex NetJosh Coombs2012-07-271-0/+1
| | | | | | | | This patch supplies the necessary DTS and supporting files to boot up a Seagate GoFlex Net with 3.5.0-rc3. Signed-off-by: Joshua Coombs <josh.coombs@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
* ARM: Kirkwood: Add basic device tree support for QNAP TS219.Andrew Lunn2012-07-271-0/+1
| | | | | | | | | The two different variants of QNAP TS devices, varying by SoC, put the GPIO keys on different GPIO lines. Hence we need two different DT board descriptions, which share the same board-ts219.c file. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetreeSimon Baatz2012-05-151-0/+1
| | | | | | | | | | | Add support for the IB-NAS6210 and IB-NAS 6220. Describe as much as currently possible in the devicetree files, including the NAND partitions. Use the partition scheme of the original firmware by default. Create a board-ib62x0.c for everything else. Signed-off-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* kirkwood: Add iconnect supportArnaud Patard (Rtp)2012-05-151-0/+1
| | | | | | | | Add support for Iomega Iconnect system. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Tested-By: Adam Baker <linux@baker-net.org.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: Basic support for DNS-320 and DNS-325Jamie Lentin2012-05-151-0/+1
| | | | | | | | | | | | | | | | | | | Add support for the DNS-320 and DNS-325. Describe as much as currently possible in the devicetree files, create a board-dnskw.c for everything else. Changes since last submission (V3) [Addressing comments by]:- * One MACH_DLINK_KIRKWOOD_DT for all dtb files [Grant Likely, Jason Cooper] * Drop brain-dead select "select CONFIG_MTD_OF_PARTS" [Grant Likely] * Don't add NAND support then throw it away immediately after [Grant Likely] * Describe purpose of MPP 41, 42 & 49 Changes since last submission (V2):- * Use IEEE-compliant "okay", rather than "ok" [Scott Wood] Signed-off-by: Jamie Lentin <jm@lentin.co.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: fdt: facilitate new boards during fdt migrationJason Cooper2012-03-161-0/+1
| | | | | | | | Move all dreamplug-specific code out of board-dt.c and into board-dreamplug.c. This way new boards that are added during the conversion to fdt don't clutter up board-dt.c. Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: add dreamplug (fdt) support.Jason Cooper2012-02-271-0/+1
| | | | | | | | | | | | | | | | | | | | Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g. Then, switched to SPI based NOR flash. After talking to Arnd Bergman, chose an incremental approach to adding devicetree support. First, we use the dtb to tell us we are on the dreamplug, then we gradually port over drivers. Driver porting will start with the uart (see next patch), and progress from there. Possibly, spi/flash/partitions will be next. When done, board-dt.c will no longer be dreamplug specific, and dt's can be made for the other kirkwood boards. Signed-off-by: Jason Cooper <jason@lakedaemon.net> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* [ARM] Kirkwood: remove duplicated code in LaCie setup filesSimon Guinot2010-09-201-6/+6
| | | | | Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* [ARM] Kirkwood: add LaCie d2 Network v2 supportSimon Guinot2010-09-201-0/+1
| | | | | Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* [ARM] Kirkwood: support for Seagate DockStarEric Cooper2010-09-201-0/+1
| | | | | | | | This patch adds support for the Seagate FreeAgent DockStar, a Marvell SheevaPlug variant. Signed-off-by: Eric Cooper <ecc@cmu.edu> Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* [ARM] Kirkwood: add LaCie Network Space Max v2 supportSimon Guinot2010-07-171-0/+1
| | | | | Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* [ARM] Kirkwood: Add support for HP t5325 Thin ClientMartin Michlmayr2010-07-171-0/+1
| | | | | | | | | Add support for the HP t5325 Thin Client. This thin client is based on a Marvell Kirkwood chip at 1.2 GHz and features 512 MB RAM, 512 MB SATA-attached flash and an XGI Volari Z11 GPU. Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* [ARM] Kirkwood: merge net2big_v2 and net5big_v2 board setupsSimon Guinot2010-05-031-2/+2
| | | | Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* [ARM] Kirkwood: add LaCie 5Big Network v2 supportSimon Guinot2010-05-031-0/+1
| | | | Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* [ARM] Kirkwood: add LaCie 2Big Network v2 supportSimon Guinot2010-05-031-0/+1
| | | | Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* [ARM] Kirkwood: Marvell GuruPlug supportSiddarth Gore2010-05-031-0/+1
| | | | | | | | | | | | | | | GuruPlug Standard: 1 Gb Ethernet, 2 USB 2.0 GuruPlug Plus: 2 Gb Ethernet, 2 USB 2.0, 1 eSATA, 1 uSD slot References: http://www.globalscaletechnologies.com/t-guruplugdetails.aspx http://plugcomputer.org This patch is for GuruPlug Plus, but it supports Standard version as well. Signed-off-by: Siddarth Gore <gores@marvell.com> Signed-off-by: Nicolas Pitre <nico@marvell.com>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-06-28 17:34:24 +0200