1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
|
Naming and data format standards for sysfs files
------------------------------------------------
The libsensors library offers an interface to the raw sensors data
through the sysfs interface. See libsensors documentation and source for
more further information. As of writing this document, libsensors
(from lm_sensors 2.8.3) is heavily chip-dependant. Adding or updating
support for any given chip requires modifying the library's code.
This is because libsensors was written for the procfs interface
older kernel modules were using, which wasn't standardized enough.
Recent versions of libsensors (from lm_sensors 2.8.2 and later) have
support for the sysfs interface, though.
The new sysfs interface was designed to be as chip-independant as
possible.
Note that motherboards vary widely in the connections to sensor chips.
There is no standard that ensures, for example, that the second
temperature sensor is connected to the CPU, or that the second fan is on
the CPU. Also, some values reported by the chips need some computation
before they make full sense. For example, most chips can only measure
voltages between 0 and +4V. Other voltages are scaled back into that
range using external resistors. Since the values of these resistors
can change from motherboard to motherboard, the conversions cannot be
hard coded into the driver and have to be done in user space.
For this reason, even if we aim at a chip-independant libsensors, it will
still require a configuration file (e.g. /etc/sensors.conf) for proper
values conversion, labeling of inputs and hiding of unused inputs.
An alternative method that some programs use is to access the sysfs
files directly. This document briefly describes the standards that the
drivers follow, so that an application program can scan for entries and
access this data in a simple and consistent way. That said, such programs
will have to implement conversion, labeling and hiding of inputs. For
this reason, it is still not recommended to bypass the library.
If you are developing a userspace application please send us feedback on
this standard.
Note that this standard isn't completely established yet, so it is subject
to changes, even important ones. One more reason to use the library instead
of accessing sysfs files directly.
Each chip gets its own directory in the sysfs /sys/devices tree. To
find all sensor chips, it is easier to follow the symlinks from
/sys/i2c/devices/
All sysfs values are fixed point numbers. To get the true value of some
of the values, you should divide by the specified value.
There is only one value per file, unlike the older /proc specification.
The common scheme for files naming is: <type><number>_<item>. Usual
types for sensor chips are "in" (voltage), "temp" (temperature) and
"fan" (fan). Usual items are "input" (measured value), "max" (high
threshold, "min" (low threshold). Numbering usually starts from 1,
except for voltages which start from 0 (because most data sheets use
this). A number is always used for elements that can be present more
than once, even if there is a single element of the given type on the
specific chip. Other files do not refer to a specific element, so
they have a simple name, and no number.
Alarms are direct indications read from the chips. The drivers do NOT
make comparisons of readings to thresholds. This allows violations
between readings to be caught and alarmed. The exact definition of an
alarm (for example, whether a threshold must be met or must be exceeded
to cause an alarm) is chip-dependent.
-------------------------------------------------------------------------
************
* Voltages *
************
in[0-8]_min Voltage min value.
Unit: millivolt
Read/Write
in[0-8]_max Voltage max value.
Unit: millivolt
Read/Write
in[0-8]_input Voltage input value.
Unit: millivolt
Read only
Actual voltage depends on the scaling resistors on the
motherboard, as recommended in the chip datasheet.
This varies by chip and by motherboard.
Because of this variation, values are generally NOT scaled
by the chip driver, and must be done by the application.
However, some drivers (notably lm87 and via686a)
do scale, with various degrees of success.
These drivers will output the actual voltage.
Typical usage:
in0_* CPU #1 voltage (not scaled)
in1_* CPU #2 voltage (not scaled)
in2_* 3.3V nominal (not scaled)
in3_* 5.0V nominal (scaled)
in4_* 12.0V nominal (scaled)
in5_* -12.0V nominal (scaled)
in6_* -5.0V nominal (scaled)
in7_* varies
in8_* varies
cpu[0-1]_vid CPU core reference voltage.
Unit: millivolt
Read only.
Not always correct.
vrm Voltage Regulator Module version number.
Read only.
Two digit number, first is major version, second is
minor version.
Affects the way the driver calculates the CPU core reference
voltage from the vid pins.
********
* Fans *
********
fan[1-3]_min Fan minimum value
Unit: revolution/min (RPM)
Read/Write.
fan[1-3]_input Fan input value.
Unit: revolution/min (RPM)
Read only.
fan[1-3]_div Fan divisor.
Integer value in powers of two (1, 2, 4, 8, 16, 32, 64, 128).
Some chips only support values 1, 2, 4 and 8.
Note that this is actually an internal clock divisor, which
affects the measurable speed range, not the read value.
*******
* PWM *
*******
pwm[1-3] Pulse width modulation fan control.
Integer value in the range 0 to 255
Read/Write
255 is max or 100%.
pwm[1-3]_enable
Switch PWM on and off.
Not always present even if fan*_pwm is.
0 to turn off
1 to turn on in manual mode
2 to turn on in automatic mode
Read/Write
pwm[1-*]_auto_channels_temp
Select which temperature channels affect this PWM output in
auto mode. Bitfield, 1 is temp1, 2 is temp2, 4 is temp3 etc...
Which values are possible depend on the chip used.
pwm[1-*]_auto_point[1-*]_pwm
pwm[1-*]_auto_point[1-*]_temp
pwm[1-*]_auto_point[1-*]_temp_hyst
Define the PWM vs temperature curve. Number of trip points is
chip-dependent. Use this for chips which associate trip points
to PWM output channels.
OR
temp[1-*]_auto_point[1-*]_pwm
temp[1-*]_auto_point[1-*]_temp
temp[1-*]_auto_point[1-*]_temp_hyst
Define the PWM vs temperature curve. Number of trip points is
chip-dependent. Use this for chips which associate trip points
to temperature channels.
****************
* Temperatures *
****************
temp[1-3]_type Sensor type selection.
Integers 1 to 4 or thermistor Beta value (typically 3435)
Read/Write.
1: PII/Celeron Diode
2: 3904 transistor
3: thermal diode
4: thermistor (default/unknown Beta)
Not all types are supported by all chips
temp[1-4]_max Temperature max value.
Unit: millidegree Celcius
Read/Write value.
temp[1-3]_min Temperature min value.
Unit: millidegree Celcius
Read/Write value.
temp[1-3]_max_hyst
Temperature hysteresis value for max limit.
Unit: millidegree Celcius
Must be reported as an absolute temperature, NOT a delta
from the max value.
Read/Write value.
temp[1-4]_input Temperature input value.
Unit: millidegree Celcius
Read only value.
temp[1-4]_crit Temperature critical value, typically greater than
corresponding temp_max values.
Unit: millidegree Celcius
Read/Write value.
temp[1-2]_crit_hyst
Temperature hysteresis value for critical limit.
Unit: millidegree Celcius
Must be reported as an absolute temperature, NOT a delta
from the critical value.
Read/Write value.
If there are multiple temperature sensors, temp1_* is
generally the sensor inside the chip itself,
reported as "motherboard temperature". temp2_* to
temp4_* are generally sensors external to the chip
itself, for example the thermal diode inside the CPU or
a thermistor nearby.
************
* Currents *
************
Note that no known chip provides current measurements as of writing,
so this part is theoretical, so to say.
curr[1-n]_max Current max value
Unit: milliampere
Read/Write.
curr[1-n]_min Current min value.
Unit: milliampere
Read/Write.
curr[1-n]_input Current input value
Unit: milliampere
Read only.
*********
* Other *
*********
alarms Alarm bitmask.
Read only.
Integer representation of one to four bytes.
A '1' bit means an alarm.
Chips should be programmed for 'comparator' mode so that
the alarm will 'come back' after you read the register
if it is still valid.
Generally a direct representation of a chip's internal
alarm registers; there is no standard for the position
of individual bits.
Bits are defined in kernel/include/sensors.h.
alarms_in Alarm bitmask relative to in (voltage) channels
Read only
A '1' bit means an alarm, LSB corresponds to in0 and so on
Prefered to 'alarms' for newer chips
alarms_fan Alarm bitmask relative to fan channels
Read only
A '1' bit means an alarm, LSB corresponds to fan1 and so on
Prefered to 'alarms' for newer chips
alarms_temp Alarm bitmask relative to temp (temperature) channels
Read only
A '1' bit means an alarm, LSB corresponds to temp1 and so on
Prefered to 'alarms' for newer chips
beep_enable Beep/interrupt enable
0 to disable.
1 to enable.
Read/Write
beep_mask Bitmask for beep.
Same format as 'alarms' with the same bit locations.
Read/Write
eeprom Raw EEPROM data in binary form.
Read only.
pec Enable or disable PEC (SMBus only)
Read/Write
|
