summaryrefslogtreecommitdiffstats
path: root/drivers/serial/zs.h
blob: aa921b57d8278b8606de9c0ceae58a90688b7780 (plain) (blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
/*
 * zs.h: Definitions for the DECstation Z85C30 serial driver.
 *
 * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.
 * Adapted from drivers/macintosh/macserial.h by Harald Koerfgen.
 *
 * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
 * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
 * Copyright (C) 2004, 2005, 2007  Maciej W. Rozycki
 */
#ifndef _SERIAL_ZS_H
#define _SERIAL_ZS_H

#ifdef __KERNEL__

#define ZS_NUM_REGS 16

/*
 * This is our internal structure for each serial port's state.
 */
struct zs_port {
	struct zs_scc	*scc;			/* Containing SCC.  */
	struct uart_port port;			/* Underlying UART.  */

	int		clk_mode;		/* May be 1, 16, 32, or 64.  */

	unsigned int	tty_break;		/* Set on BREAK condition.  */
	int		tx_stopped;		/* Output is suspended.  */

	unsigned int	mctrl;			/* State of modem lines.  */
	u8		brk;			/* BREAK state from RR0.  */

	u8		regs[ZS_NUM_REGS];	/* Channel write registers.  */
};

/*
 * Per-SCC state for locking and the interrupt handler.
 */
struct zs_scc {
	struct zs_port	zport[2];
	spinlock_t	zlock;
	atomic_t	irq_guard;
	int		initialised;
};

#endif /* __KERNEL__ */

/*
 * Conversion routines to/from brg time constants from/to bits per second.
 */
#define ZS_BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
#define ZS_BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)

/*
 * The Zilog register set.
 */

/* Write Register 0 (Command) */
#define R0		0	/* Register selects */
#define R1		1
#define R2		2
#define R3		3
#define R4		4
#define R5		5
#define R6		6
#define R7		7
#define R8		8
#define R9		9
#define R10		10
#define R11		11
#define R12		12
#define R13		13
#define R14		14
#define R15		15

#define NULLCODE	0	/* Null Code */
#define POINT_HIGH	0x8	/* Select upper half of registers */
#define RES_EXT_INT	0x10	/* Reset Ext. Status Interrupts */
#define SEND_ABORT	0x18	/* HDLC Abort */
#define RES_RxINT_FC	0x20	/* Reset RxINT on First Character */
#define RES_Tx_P	0x28	/* Reset TxINT Pending */
#define ERR_RES		0x30	/* Error Reset */
#define RES_H_IUS	0x38	/* Reset highest IUS */

#define RES_Rx_CRC	0x40	/* Reset Rx CRC Checker */
#define RES_Tx_CRC	0x80	/* Reset Tx CRC Checker */
#define RES_EOM_L	0xC0	/* Reset EOM latch */

/* Write Register 1 (Tx/Rx/Ext Int Enable and WAIT/DMA Commands) */
#define EXT_INT_ENAB	0x1	/* Ext Int Enable */
#define TxINT_ENAB	0x2	/* Tx Int Enable */
#define PAR_SPEC	0x4	/* Parity is special condition */

#define RxINT_DISAB	0	/* Rx Int Disable */
#define RxINT_FCERR	0x8	/* Rx Int on First Character Only or Error */
#define RxINT_ALL	0x10	/* Int on all Rx Characters or error */
#define RxINT_ERR	0x18	/* Int on error only */
#define RxINT_MASK	0x18

#define WT_RDY_RT	0x20	/* Wait/Ready on R/T */
#define WT_FN_RDYFN	0x40	/* Wait/FN/Ready FN */
#define WT_RDY_ENAB	0x80	/* Wait/Ready Enable */

/* Write Register 2 (Interrupt Vector) */

/* Write Register 3 (Receive Parameters and Control) */
#define RxENABLE	0x1	/* Rx Enable */
#define SYNC_L_INH	0x2	/* Sync Character Load Inhibit */
#define ADD_SM		0x4	/* Address Search Mode (SDLC) */
#define RxCRC_ENAB	0x8	/* Rx CRC Enable */
#define ENT_HM		0x10	/* Enter Hunt Mode */
#define AUTO_ENAB	0x20	/* Auto Enables */
#define Rx5		0x0	/* Rx 5 Bits/Character */
#define Rx7		0x40	/* Rx 7 Bits/Character */
#define Rx6		0x80	/* Rx 6 Bits/Character */
#define Rx8		0xc0	/* Rx 8 Bits/Character */
#define RxNBITS_MASK	0xc0

/* Write Register 4 (Transmit/Receive Miscellaneous Parameters and Modes) */
#define PAR_ENA		0x1	/* Parity Enable */
#define PAR_EVEN	0x2	/* Parity Even/Odd* */

#define SYNC_ENAB	0	/* Sync Modes Enable */
#define SB1		0x4	/* 1 stop bit/char */
#define SB15		0x8	/* 1.5 stop bits/char */
#define SB2		0xc	/* 2 stop bits/char */
#define SB_MASK		0xc

#define MONSYNC		0	/* 8 Bit Sync character */
#define BISYNC		0x10	/* 16 bit sync character */
#define SDLC		0x20	/* SDLC Mode (01111110 Sync Flag) */
#define EXTSYNC		0x30	/* External Sync Mode */

#define X1CLK		0x0	/* x1 clock mode */
#define X16CLK		0x40	/* x16 clock mode */
#define X32CLK		0x80	/* x32 clock mode */
#define X64CLK		0xc0	/* x64 clock mode */
#define XCLK_MASK	0xc0

/* Write Register 5 (Transmit Parameters and Controls) */
#define TxCRC_ENAB	0x1	/* Tx CRC Enable */
#define RTS		0x2	/* RTS */
#define SDLC_CRC	0x4	/* SDLC/CRC-16 */
#define TxENAB		0x8	/* Tx Enable */
#define SND_BRK		0x10	/* Send Break */
#define Tx5		0x0	/* Tx 5 bits (or less)/character */
#define Tx7		0x20	/* Tx 7 bits/character */
#define Tx6		0x40	/* Tx 6 bits/character */
#define Tx8		0x60	/* Tx 8 bits/character */
#define TxNBITS_MASK	0x60
#define DTR		0x80	/* DTR */

/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */

/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */

/* Write Register 8 (Transmit Buffer) */

/* Write Register 9 (Master Interrupt Control) */
#define VIS		1	/* Vector Includes Status */
#define NV		2	/* No Vector */
#define DLC		4	/* Disable Lower Chain */
#define MIE		8	/* Master Interrupt Enable */
#define STATHI		0x10	/* Status high */
#define SOFTACK		0x20	/* Software Interrupt Acknowledge */
#define NORESET		0	/* No reset on write to R9 */
#define CHRB		0x40	/* Reset channel B */
#define CHRA		0x80	/* Reset channel A */
#define FHWRES		0xc0	/* Force hardware reset */

/* Write Register 10 (Miscellaneous Transmitter/Receiver Control Bits) */
#define BIT6		1	/* 6 bit/8bit sync */
#define LOOPMODE	2	/* SDLC Loop mode */
#define ABUNDER		4	/* Abort/flag on SDLC xmit underrun */
#define MARKIDLE	8	/* Mark/flag on idle */
#define GAOP		0x10	/* Go active on poll */
#define NRZ		0	/* NRZ mode */
#define NRZI		0x20	/* NRZI mode */
#define FM1		0x40	/* FM1 (transition = 1) */
#define FM0		0x60	/* FM0 (transition = 0) */
#define CRCPS		0x80	/* CRC Preset I/O */

/* Write Register 11 (Clock Mode Control) */
#define TRxCXT		0	/* TRxC = Xtal output */
#define TRxCTC		1	/* TRxC = Transmit clock */
#define TRxCBR		2	/* TRxC = BR Generator Output */
#define TRxCDP		3	/* TRxC = DPLL output */
#define TRxCOI		4	/* TRxC O/I */
#define TCRTxCP		0	/* Transmit clock = RTxC pin */
#define TCTRxCP		8	/* Transmit clock = TRxC pin */
#define TCBR		0x10	/* Transmit clock = BR Generator output */
#define TCDPLL		0x18	/* Transmit clock = DPLL output */
#define RCRTxCP		0	/* Receive clock = RTxC pin */
#define RCTRxCP		0x20	/* Receive clock = TRxC pin */
#define RCBR		0x40	/* Receive clock = BR Generator output */
#define RCDPLL		0x60	/* Receive clock = DPLL output */
#define RTxCX		0x80	/* RTxC Xtal/No Xtal */

/* Write Register 12 (Lower Byte of Baud Rate Generator Time Constant) */

/* Write Register 13 (Upper Byte of Baud Rate Generator Time Constant) */

/* Write Register 14 (Miscellaneous Control Bits) */
#define BRENABL		1	/* Baud rate generator enable */
#define BRSRC		2	/* Baud rate generator source */
#define DTRREQ		4	/* DTR/Request function */
#define AUTOECHO	8	/* Auto Echo */
#define LOOPBAK		0x10	/* Local loopback */
#define SEARCH		0x20	/* Enter search mode */
#define RMC		0x40	/* Reset missing clock */
#define DISDPLL		0x60	/* Disable DPLL */
#define SSBR		0x80	/* Set DPLL source = BR generator */
#define SSRTxC		0xa0	/* Set DPLL source = RTxC */
#define SFMM		0xc0	/* Set FM mode */
#define SNRZI		0xe0	/* Set NRZI mode */

/* Write Register 15 (External/Status Interrupt Control) */
#define WR7P_EN		1	/* WR7 Prime SDLC Feature Enable */
#define ZCIE		2	/* Zero count IE */
#define DCDIE		8	/* DCD IE */
#define SYNCIE		0x10	/* Sync/hunt IE */
#define CTSIE		0x20	/* CTS IE */
#define TxUIE		0x40	/* Tx Underrun/EOM IE */
#define BRKIE		0x80	/* Break/Abort IE */


/* Read Register 0 (Transmit/Receive Buffer Status and External Status) */
#define Rx_CH_AV	0x1	/* Rx Character Available */
#define ZCOUNT		0x2	/* Zero count */
#define Tx_BUF_EMP	0x4	/* Tx Buffer empty */
#define DCD		0x8	/* DCD */
#define SYNC_HUNT	0x10	/* Sync/hunt */
#define CTS		0x20	/* CTS */
#define TxEOM		0x40	/* Tx underrun */
#define BRK_ABRT	0x80	/* Break/Abort */

/* Read Register 1 (Special Receive Condition Status) */
#define ALL_SNT		0x1	/* All sent */
/* Residue Data for 8 Rx bits/char programmed */
#define RES3		0x8	/* 0/3 */
#define RES4		0x4	/* 0/4 */
#define RES5		0xc	/* 0/5 */
#define RES6		0x2	/* 0/6 */
#define RES7		0xa	/* 0/7 */
#define RES8		0x6	/* 0/8 */
#define RES18		0xe	/* 1/8 */
#define RES28		0x0	/* 2/8 */
/* Special Rx Condition Interrupts */
#define PAR_ERR		0x10	/* Parity Error */
#define Rx_OVR		0x20	/* Rx Overrun Error */
#define FRM_ERR		0x40	/* CRC/Framing Error */
#define END_FR		0x80	/* End of Frame (SDLC) */

/* Read Register 2 (Interrupt Vector (WR2) -- channel A).  */

/* Read Register 2 (Modified Interrupt Vector -- channel B).  */

/* Read Register 3 (Interrupt Pending Bits -- channel A only).  */
#define CHBEXT		0x1	/* Channel B Ext/Stat IP */
#define CHBTxIP		0x2	/* Channel B Tx IP */
#define CHBRxIP		0x4	/* Channel B Rx IP */
#define CHAEXT		0x8	/* Channel A Ext/Stat IP */
#define CHATxIP		0x10	/* Channel A Tx IP */
#define CHARxIP		0x20	/* Channel A Rx IP */

/* Read Register 6 (SDLC FIFO Status and Byte Count LSB) */

/* Read Register 7 (SDLC FIFO Status and Byte Count MSB) */

/* Read Register 8 (Receive Data) */

/* Read Register 10 (Miscellaneous Status Bits) */
#define ONLOOP		2	/* On loop */
#define LOOPSEND	0x10	/* Loop sending */
#define CLK2MIS		0x40	/* Two clocks missing */
#define CLK1MIS		0x80	/* One clock missing */

/* Read Register 12 (Lower Byte of Baud Rate Generator Constant (WR12)) */

/* Read Register 13 (Upper Byte of Baud Rate Generator Constant (WR13) */

/* Read Register 15 (External/Status Interrupt Control (WR15)) */

#endif /* _SERIAL_ZS_H */