diff options
Diffstat (limited to 'contrib/syslinux-4.02/gpxe/src/include/gpxe/efi/Protocol/PciIo.h')
| -rw-r--r-- | contrib/syslinux-4.02/gpxe/src/include/gpxe/efi/Protocol/PciIo.h | 519 |
1 files changed, 519 insertions, 0 deletions
diff --git a/contrib/syslinux-4.02/gpxe/src/include/gpxe/efi/Protocol/PciIo.h b/contrib/syslinux-4.02/gpxe/src/include/gpxe/efi/Protocol/PciIo.h new file mode 100644 index 0000000..5aea5b4 --- /dev/null +++ b/contrib/syslinux-4.02/gpxe/src/include/gpxe/efi/Protocol/PciIo.h @@ -0,0 +1,519 @@ +/** @file + EFI PCI I/O Protocol provides the basic Memory, I/O, PCI configuration, + and DMA interfaces that a driver uses to access its PCI controller. + + Copyright (c) 2006 - 2008, Intel Corporation + All rights reserved. This program and the accompanying materials + are licensed and made available under the terms and conditions of the BSD License + which accompanies this distribution. The full text of the license may be found at + http://opensource.org/licenses/bsd-license.php + + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. + +**/ + +#ifndef __PCI_IO_H__ +#define __PCI_IO_H__ + +/// +/// Global ID for the PCI I/O Protocol +/// +#define EFI_PCI_IO_PROTOCOL_GUID \ + { \ + 0x4cf5b200, 0x68b8, 0x4ca5, {0x9e, 0xec, 0xb2, 0x3e, 0x3f, 0x50, 0x2, 0x9a } \ + } + +typedef struct _EFI_PCI_IO_PROTOCOL EFI_PCI_IO_PROTOCOL; + +/// +/// Prototypes for the PCI I/O Protocol +/// +typedef enum { + EfiPciIoWidthUint8 = 0, + EfiPciIoWidthUint16, + EfiPciIoWidthUint32, + EfiPciIoWidthUint64, + EfiPciIoWidthFifoUint8, + EfiPciIoWidthFifoUint16, + EfiPciIoWidthFifoUint32, + EfiPciIoWidthFifoUint64, + EfiPciIoWidthFillUint8, + EfiPciIoWidthFillUint16, + EfiPciIoWidthFillUint32, + EfiPciIoWidthFillUint64, + EfiPciIoWidthMaximum +} EFI_PCI_IO_PROTOCOL_WIDTH; + +// +// Complete PCI address generater +// +#define EFI_PCI_IO_PASS_THROUGH_BAR 0xff ///< Special BAR that passes a memory or I/O cycle through unchanged +#define EFI_PCI_IO_ATTRIBUTE_MASK 0x077f ///< All the following I/O and Memory cycles +#define EFI_PCI_IO_ATTRIBUTE_ISA_MOTHERBOARD_IO 0x0001 ///< I/O cycles 0x0000-0x00FF (10 bit decode) +#define EFI_PCI_IO_ATTRIBUTE_ISA_IO 0x0002 ///< I/O cycles 0x0100-0x03FF or greater (10 bit decode) +#define EFI_PCI_IO_ATTRIBUTE_VGA_PALETTE_IO 0x0004 ///< I/O cycles 0x3C6, 0x3C8, 0x3C9 (10 bit decode) +#define EFI_PCI_IO_ATTRIBUTE_VGA_MEMORY 0x0008 ///< MEM cycles 0xA0000-0xBFFFF (24 bit decode) +#define EFI_PCI_IO_ATTRIBUTE_VGA_IO 0x0010 ///< I/O cycles 0x3B0-0x3BB and 0x3C0-0x3DF (10 bit decode) +#define EFI_PCI_IO_ATTRIBUTE_IDE_PRIMARY_IO 0x0020 ///< I/O cycles 0x1F0-0x1F7, 0x3F6, 0x3F7 (10 bit decode) +#define EFI_PCI_IO_ATTRIBUTE_IDE_SECONDARY_IO 0x0040 ///< I/O cycles 0x170-0x177, 0x376, 0x377 (10 bit decode) +#define EFI_PCI_IO_ATTRIBUTE_MEMORY_WRITE_COMBINE 0x0080 ///< Map a memory range so write are combined +#define EFI_PCI_IO_ATTRIBUTE_IO 0x0100 ///< Enable the I/O decode bit in the PCI Config Header +#define EFI_PCI_IO_ATTRIBUTE_MEMORY 0x0200 ///< Enable the Memory decode bit in the PCI Config Header +#define EFI_PCI_IO_ATTRIBUTE_BUS_MASTER 0x0400 ///< Enable the DMA bit in the PCI Config Header +#define EFI_PCI_IO_ATTRIBUTE_MEMORY_CACHED 0x0800 ///< Map a memory range so all r/w accesses are cached +#define EFI_PCI_IO_ATTRIBUTE_MEMORY_DISABLE 0x1000 ///< Disable a memory range +#define EFI_PCI_IO_ATTRIBUTE_EMBEDDED_DEVICE 0x2000 ///< Clear for an add-in PCI Device +#define EFI_PCI_IO_ATTRIBUTE_EMBEDDED_ROM 0x4000 ///< Clear for a physical PCI Option ROM accessed through ROM BAR +#define EFI_PCI_IO_ATTRIBUTE_DUAL_ADDRESS_CYCLE 0x8000 ///< Clear for PCI controllers that can not genrate a DAC +#define EFI_PCI_IO_ATTRIBUTE_ISA_IO_16 0x10000 ///< I/O cycles 0x0100-0x03FF or greater (16 bit decode) +#define EFI_PCI_IO_ATTRIBUTE_VGA_PALETTE_IO_16 0x20000 ///< I/O cycles 0x3C6, 0x3C8, 0x3C9 (16 bit decode) +#define EFI_PCI_IO_ATTRIBUTE_VGA_IO_16 0x30000 ///< I/O cycles 0x3B0-0x3BB and 0x3C0-0x3DF (16 bit decode) + +#define EFI_PCI_DEVICE_ENABLE (EFI_PCI_IO_ATTRIBUTE_IO | EFI_PCI_IO_ATTRIBUTE_MEMORY | EFI_PCI_IO_ATTRIBUTE_BUS_MASTER) +#define EFI_VGA_DEVICE_ENABLE (EFI_PCI_IO_ATTRIBUTE_VGA_PALETTE_IO | EFI_PCI_IO_ATTRIBUTE_VGA_MEMORY | EFI_PCI_IO_ATTRIBUTE_VGA_IO | EFI_PCI_IO_ATTRIBUTE_IO) + +/// +/// ******************************************************* +/// EFI_PCI_IO_PROTOCOL_OPERATION +/// ******************************************************* +/// +typedef enum { + EfiPciIoOperationBusMasterRead, + EfiPciIoOperationBusMasterWrite, + EfiPciIoOperationBusMasterCommonBuffer, + EfiPciIoOperationMaximum +} EFI_PCI_IO_PROTOCOL_OPERATION; + +/// +/// ******************************************************* +/// EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION +/// ******************************************************* +/// +typedef enum { + EfiPciIoAttributeOperationGet, + EfiPciIoAttributeOperationSet, + EfiPciIoAttributeOperationEnable, + EfiPciIoAttributeOperationDisable, + EfiPciIoAttributeOperationSupported, + EfiPciIoAttributeOperationMaximum +} EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION; + +/** + Reads from the memory space of a PCI controller. Returns when either the polling exit criteria is + satisfied or after a defined duration. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param Width Signifies the width of the memory or I/O operations. + @param BarIndex The BAR index of the standard PCI Configuration header to use as the + base address for the memory operation to perform. + @param Offset The offset within the selected BAR to start the memory operation. + @param Mask Mask used for the polling criteria. + @param Value The comparison value used for the polling exit criteria. + @param Delay The number of 100 ns units to poll. + @param Result Pointer to the last value read from the memory location. + + @retval EFI_SUCCESS The last data returned from the access matched the poll exit criteria. + @retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller. + @retval EFI_UNSUPPORTED Offset is not valid for the BarIndex of this PCI controller. + @retval EFI_TIMEOUT Delay expired before a match occurred. + @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. + @retval EFI_INVALID_PARAMETER One or more parameters are invalid. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_POLL_IO_MEM)( + IN EFI_PCI_IO_PROTOCOL *This, + IN EFI_PCI_IO_PROTOCOL_WIDTH Width, + IN UINT8 BarIndex, + IN UINT64 Offset, + IN UINT64 Mask, + IN UINT64 Value, + IN UINT64 Delay, + OUT UINT64 *Result + ); + +/** + Enable a PCI driver to access PCI controller registers in the PCI memory or I/O space. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param Width Signifies the width of the memory or I/O operations. + @param BarIndex The BAR index of the standard PCI Configuration header to use as the + base address for the memory or I/O operation to perform. + @param Offset The offset within the selected BAR to start the memory or I/O operation. + @param Count The number of memory or I/O operations to perform. + @param Buffer For read operations, the destination buffer to store the results. For write + operations, the source buffer to write data from. + + @retval EFI_SUCCESS The data was read from or written to the PCI controller. + @retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller. + @retval EFI_UNSUPPORTED The address range specified by Offset, Width, and Count is not + valid for the PCI BAR specified by BarIndex. + @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. + @retval EFI_INVALID_PARAMETER One or more parameters are invalid. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_IO_MEM)( + IN EFI_PCI_IO_PROTOCOL *This, + IN EFI_PCI_IO_PROTOCOL_WIDTH Width, + IN UINT8 BarIndex, + IN UINT64 Offset, + IN UINTN Count, + IN OUT VOID *Buffer + ); + +typedef struct { + EFI_PCI_IO_PROTOCOL_IO_MEM Read; + EFI_PCI_IO_PROTOCOL_IO_MEM Write; +} EFI_PCI_IO_PROTOCOL_ACCESS; + +/** + Enable a PCI driver to access PCI controller registers in PCI configuration space. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param Width Signifies the width of the memory operations. + @param Offset The offset within the PCI configuration space for the PCI controller. + @param Count The number of PCI configuration operations to perform. + @param Buffer For read operations, the destination buffer to store the results. For write + operations, the source buffer to write data from. + + + @retval EFI_SUCCESS The data was read from or written to the PCI controller. + @retval EFI_UNSUPPORTED The address range specified by Offset, Width, and Count is not + valid for the PCI configuration header of the PCI controller. + @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. + @retval EFI_INVALID_PARAMETER Buffer is NULL or Width is invalid. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_CONFIG)( + IN EFI_PCI_IO_PROTOCOL *This, + IN EFI_PCI_IO_PROTOCOL_WIDTH Width, + IN UINT32 Offset, + IN UINTN Count, + IN OUT VOID *Buffer + ); + +typedef struct { + EFI_PCI_IO_PROTOCOL_CONFIG Read; + EFI_PCI_IO_PROTOCOL_CONFIG Write; +} EFI_PCI_IO_PROTOCOL_CONFIG_ACCESS; + +/** + Enables a PCI driver to copy one region of PCI memory space to another region of PCI + memory space. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param Width Signifies the width of the memory operations. + @param DestBarIndex The BAR index in the standard PCI Configuration header to use as the + base address for the memory operation to perform. + @param DestOffset The destination offset within the BAR specified by DestBarIndex to + start the memory writes for the copy operation. + @param SrcBarIndex The BAR index in the standard PCI Configuration header to use as the + base address for the memory operation to perform. + @param SrcOffset The source offset within the BAR specified by SrcBarIndex to start + the memory reads for the copy operation. + @param Count The number of memory operations to perform. Bytes moved is Width + size * Count, starting at DestOffset and SrcOffset. + + @retval EFI_SUCCESS The data was copied from one memory region to another memory region. + @retval EFI_UNSUPPORTED DestBarIndex not valid for this PCI controller. + @retval EFI_UNSUPPORTED SrcBarIndex not valid for this PCI controller. + @retval EFI_UNSUPPORTED The address range specified by DestOffset, Width, and Count + is not valid for the PCI BAR specified by DestBarIndex. + @retval EFI_UNSUPPORTED The address range specified by SrcOffset, Width, and Count is + not valid for the PCI BAR specified by SrcBarIndex. + @retval EFI_INVALID_PARAMETER Width is invalid. + @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_COPY_MEM)( + IN EFI_PCI_IO_PROTOCOL *This, + IN EFI_PCI_IO_PROTOCOL_WIDTH Width, + IN UINT8 DestBarIndex, + IN UINT64 DestOffset, + IN UINT8 SrcBarIndex, + IN UINT64 SrcOffset, + IN UINTN Count + ); + +/** + Provides the PCI controller-Cspecific addresses needed to access system memory. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param Operation Indicates if the bus master is going to read or write to system memory. + @param HostAddress The system memory address to map to the PCI controller. + @param NumberOfBytes On input the number of bytes to map. On output the number of bytes + that were mapped. + @param DeviceAddress The resulting map address for the bus master PCI controller to use to + access the hosts HostAddress. + @param Mapping A resulting value to pass to Unmap(). + + @retval EFI_SUCCESS The range was mapped for the returned NumberOfBytes. + @retval EFI_UNSUPPORTED The HostAddress cannot be mapped as a common buffer. + @retval EFI_INVALID_PARAMETER One or more parameters are invalid. + @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. + @retval EFI_DEVICE_ERROR The system hardware could not map the requested address. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_MAP)( + IN EFI_PCI_IO_PROTOCOL *This, + IN EFI_PCI_IO_PROTOCOL_OPERATION Operation, + IN VOID *HostAddress, + IN OUT UINTN *NumberOfBytes, + OUT EFI_PHYSICAL_ADDRESS *DeviceAddress, + OUT VOID **Mapping + ); + +/** + Completes the Map() operation and releases any corresponding resources. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param Mapping The mapping value returned from Map(). + + @retval EFI_SUCCESS The range was unmapped. + @retval EFI_DEVICE_ERROR The data was not committed to the target system memory. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_UNMAP)( + IN EFI_PCI_IO_PROTOCOL *This, + IN VOID *Mapping + ); + +/** + Allocates pages that are suitable for an EfiPciIoOperationBusMasterCommonBuffer + mapping. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param Type This parameter is not used and must be ignored. + @param MemoryType The type of memory to allocate, EfiBootServicesData or + EfiRuntimeServicesData. + @param Pages The number of pages to allocate. + @param HostAddress A pointer to store the base system memory address of the + allocated range. + @param Attributes The requested bit mask of attributes for the allocated range. + + @retval EFI_SUCCESS The requested memory pages were allocated. + @retval EFI_UNSUPPORTED Attributes is unsupported. The only legal attribute bits are + MEMORY_WRITE_COMBINE and MEMORY_CACHED. + @retval EFI_INVALID_PARAMETER One or more parameters are invalid. + @retval EFI_OUT_OF_RESOURCES The memory pages could not be allocated. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_ALLOCATE_BUFFER)( + IN EFI_PCI_IO_PROTOCOL *This, + IN EFI_ALLOCATE_TYPE Type, + IN EFI_MEMORY_TYPE MemoryType, + IN UINTN Pages, + OUT VOID **HostAddress, + IN UINT64 Attributes + ); + +/** + Frees memory that was allocated with AllocateBuffer(). + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param Pages The number of pages to free. + @param HostAddress The base system memory address of the allocated range. + + @retval EFI_SUCCESS The requested memory pages were freed. + @retval EFI_INVALID_PARAMETER The memory range specified by HostAddress and Pages + was not allocated with AllocateBuffer(). + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_FREE_BUFFER)( + IN EFI_PCI_IO_PROTOCOL *This, + IN UINTN Pages, + IN VOID *HostAddress + ); + +/** + Flushes all PCI posted write transactions from a PCI host bridge to system memory. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + + @retval EFI_SUCCESS The PCI posted write transactions were flushed from the PCI host + bridge to system memory. + @retval EFI_DEVICE_ERROR The PCI posted write transactions were not flushed from the PCI + host bridge due to a hardware error. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_FLUSH)( + IN EFI_PCI_IO_PROTOCOL *This + ); + +/** + Retrieves this PCI controller's current PCI bus number, device number, and function number. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param SegmentNumber The PCI controller's current PCI segment number. + @param BusNumber The PCI controller's current PCI bus number. + @param DeviceNumber The PCI controller's current PCI device number. + @param FunctionNumber The PCI controller's current PCI function number. + + @retval EFI_SUCCESS The PCI controller location was returned. + @retval EFI_INVALID_PARAMETER One or more parameters are invalid. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_GET_LOCATION)( + IN EFI_PCI_IO_PROTOCOL *This, + OUT UINTN *SegmentNumber, + OUT UINTN *BusNumber, + OUT UINTN *DeviceNumber, + OUT UINTN *FunctionNumber + ); + +/** + Performs an operation on the attributes that this PCI controller supports. The operations include + getting the set of supported attributes, retrieving the current attributes, setting the current + attributes, enabling attributes, and disabling attributes. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param Operation The operation to perform on the attributes for this PCI controller. + @param Attributes The mask of attributes that are used for Set, Enable, and Disable + operations. + @param Result A pointer to the result mask of attributes that are returned for the Get + and Supported operations. + + @retval EFI_SUCCESS The operation on the PCI controller's attributes was completed. + @retval EFI_INVALID_PARAMETER One or more parameters are invalid. + @retval EFI_UNSUPPORTED one or more of the bits set in + Attributes are not supported by this PCI controller or one of + its parent bridges when Operation is Set, Enable or Disable. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_ATTRIBUTES)( + IN EFI_PCI_IO_PROTOCOL *This, + IN EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION Operation, + IN UINT64 Attributes, + OUT UINT64 *Result OPTIONAL + ); + +/** + Gets the attributes that this PCI controller supports setting on a BAR using + SetBarAttributes(), and retrieves the list of resource descriptors for a BAR. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param BarIndex The BAR index of the standard PCI Configuration header to use as the + base address for resource range. The legal range for this field is 0..5. + @param Supports A pointer to the mask of attributes that this PCI controller supports + setting for this BAR with SetBarAttributes(). + @param Resources A pointer to the ACPI 2.0 resource descriptors that describe the current + configuration of this BAR of the PCI controller. + + @retval EFI_SUCCESS If Supports is not NULL, then the attributes that the PCI + controller supports are returned in Supports. If Resources + is not NULL, then the ACPI 2.0 resource descriptors that the PCI + controller is currently using are returned in Resources. + @retval EFI_INVALID_PARAMETER Both Supports and Attributes are NULL. + @retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller. + @retval EFI_OUT_OF_RESOURCES There are not enough resources available to allocate + Resources. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_GET_BAR_ATTRIBUTES)( + IN EFI_PCI_IO_PROTOCOL *This, + IN UINT8 BarIndex, + OUT UINT64 *Supports, OPTIONAL + OUT VOID **Resources OPTIONAL + ); + +/** + Sets the attributes for a range of a BAR on a PCI controller. + + @param This A pointer to the EFI_PCI_IO_PROTOCOL instance. + @param Attributes The mask of attributes to set for the resource range specified by + BarIndex, Offset, and Length. + @param BarIndex The BAR index of the standard PCI Configuration header to use as the + base address for resource range. The legal range for this field is 0..5. + @param Offset A pointer to the BAR relative base address of the resource range to be + modified by the attributes specified by Attributes. + @param Length A pointer to the length of the resource range to be modified by the + attributes specified by Attributes. + + @retval EFI_SUCCESS The set of attributes specified by Attributes for the resource + range specified by BarIndex, Offset, and Length were + set on the PCI controller, and the actual resource range is returned + in Offset and Length. + @retval EFI_INVALID_PARAMETER Offset or Length is NULL. + @retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller. + @retval EFI_OUT_OF_RESOURCES There are not enough resources to set the attributes on the + resource range specified by BarIndex, Offset, and + Length. + +**/ +typedef +EFI_STATUS +(EFIAPI *EFI_PCI_IO_PROTOCOL_SET_BAR_ATTRIBUTES)( + IN EFI_PCI_IO_PROTOCOL *This, + IN UINT64 Attributes, + IN UINT8 BarIndex, + IN OUT UINT64 *Offset, + IN OUT UINT64 *Length + ); + +/// +/// The EFI_PCI_IO_PROTOCOL provides the basic Memory, I/O, PCI configuration, +/// and DMA interfaces that are used to abstract accesses to PCI controllers. +/// There is one EFI_PCI_IO_PROTOCOL instance for each PCI controller on a PCI bus. +/// A device driver that wishes to manage a PCI controller in a system will have to +/// retrieve the EFI_PCI_IO_PROTOCOL instance that is associated with the PCI controller. +/// +struct _EFI_PCI_IO_PROTOCOL { + EFI_PCI_IO_PROTOCOL_POLL_IO_MEM PollMem; + EFI_PCI_IO_PROTOCOL_POLL_IO_MEM PollIo; + EFI_PCI_IO_PROTOCOL_ACCESS Mem; + EFI_PCI_IO_PROTOCOL_ACCESS Io; + EFI_PCI_IO_PROTOCOL_CONFIG_ACCESS Pci; + EFI_PCI_IO_PROTOCOL_COPY_MEM CopyMem; + EFI_PCI_IO_PROTOCOL_MAP Map; + EFI_PCI_IO_PROTOCOL_UNMAP Unmap; + EFI_PCI_IO_PROTOCOL_ALLOCATE_BUFFER AllocateBuffer; + EFI_PCI_IO_PROTOCOL_FREE_BUFFER FreeBuffer; + EFI_PCI_IO_PROTOCOL_FLUSH Flush; + EFI_PCI_IO_PROTOCOL_GET_LOCATION GetLocation; + EFI_PCI_IO_PROTOCOL_ATTRIBUTES Attributes; + EFI_PCI_IO_PROTOCOL_GET_BAR_ATTRIBUTES GetBarAttributes; + EFI_PCI_IO_PROTOCOL_SET_BAR_ATTRIBUTES SetBarAttributes; + + /// + /// The size, in bytes, of the ROM image. + /// + UINT64 RomSize; + + /// + /// A pointer to the in memory copy of the ROM image. The PCI Bus Driver is responsible + /// for allocating memory for the ROM image, and copying the contents of the ROM to memory. + /// The contents of this buffer are either from the PCI option ROM that can be accessed + /// through the ROM BAR of the PCI controller, or it is from a platform-specific location. + /// The Attributes() function can be used to determine from which of these two sources + /// the RomImage buffer was initialized. + /// + VOID *RomImage; +}; + +extern EFI_GUID gEfiPciIoProtocolGuid; + +#endif |