/* linux/arch/arm/plat-s3c/include/plat/gpio-cfg.h
*
* Copyright 2008 Openmoko, Inc.
* Copyright 2008 Simtec Electronics
* http://armlinux.simtec.co.uk/
* Ben Dooks <ben@simtec.co.uk>
*
* S3C Platform - GPIO pin configuration
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/* This file contains the necessary definitions to get the basic gpio
* pin configuration done such as setting a pin to input or output or
* changing the pull-{up,down} configurations.
*/
/* Note, this interface is being added to the s3c64xx arch first and will
* be added to the s3c24xx systems later.
*/
#ifndef __PLAT_GPIO_CFG_H
#define __PLAT_GPIO_CFG_H __FILE__
#include <linux/types.h>
typedef unsigned int __bitwise__ samsung_gpio_pull_t;
typedef unsigned int __bitwise__ s5p_gpio_drvstr_t;
/* forward declaration if gpio-core.h hasn't been included */
struct samsung_gpio_chip;
/**
* struct samsung_gpio_cfg GPIO configuration
* @cfg_eint: Configuration setting when used for external interrupt source
* @get_pull: Read the current pull configuration for the GPIO
* @set_pull: Set the current pull configuraiton for the GPIO
* @set_config: Set the current configuration for the GPIO
* @get_config: Read the current configuration for the GPIO
*
* Each chip can have more than one type of GPIO bank available and some
* have different capabilites even when they have the same control register
* layouts. Provide an point to vector control routine and provide any
* per-bank configuration information that other systems such as the
* external interrupt code will need.
*
* @sa samsung_gpio_cfgpin
* @sa s3c_gpio_getcfg
* @sa s3c_gpio_setpull
* @sa s3c_gpio_getpull
*/
struct samsung_gpio_cfg {
unsigned int cfg_eint;
samsung_gpio_pull_t (*get_pull)(struct samsung_gpio_chip *chip, unsigned offs);
int (*set_pull)(struct samsung_gpio_chip *chip, unsigned offs,
samsung_gpio_pull_t pull);
unsigned (*get_config)(struct samsung_gpio_chip *chip, unsigned offs);
int (*set_config)(struct samsung_gpio_chip *chip, unsigned offs,
unsigned config);
};
#define S3C_GPIO_SPECIAL_MARK (0xfffffff0)
#define S3C_GPIO_SPECIAL(x) (S3C_GPIO_SPECIAL_MARK | (x))
/* Defines for generic pin configurations */
#define S3C_GPIO_INPUT (S3C_GPIO_SPECIAL(0))
#define S3C_GPIO_OUTPUT (S3C_GPIO_SPECIAL(1))
#define S3C_GPIO_SFN(x) (S3C_GPIO_SPECIAL(x))
#define samsung_gpio_is_cfg_special(_cfg) \
(((_cfg) & S3C_GPIO_SPECIAL_MARK) == S3C_GPIO_SPECIAL_MARK)
/**
* s3c_gpio_cfgpin() - Change the GPIO function of a pin.
* @pin pin The pin number to configure.
* @to to The configuration for the pin's function.
*
* Configure which function is actually connected to the external
* pin, such as an gpio input, output or some form of special function
* connected to an internal peripheral block.
*
* The @to parameter can be one of the generic S3C_GPIO_INPUT, S3C_GPIO_OUTPUT
* or S3C_GPIO_SFN() to indicate one of the possible values that the helper
* will then generate the correct bit mask and shift for the configuration.
*
* If a bank of GPIOs all needs to be set to special-function 2, then
* the following code will work:
*
* for (gpio = start; gpio < end; gpio++)
* s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
*
* The @to parameter can also be a specific value already shifted to the
* correct position in the control register, although these are discouraged
* in newer kernels and are only being kept for compatibility.
*/
extern int s3c_gpio_cfgpin(unsigned int pin, unsigned int to);
/**
* s3c_gpio_getcfg - Read the current function for a GPIO pin
* @pin: The pin to read the configuration value for.
*
* Read the configuration state of the given @pin, returning a value that
* could be passed back to s3c_gpio_cfgpin().
*
* @sa s3c_gpio_cfgpin
*/
extern unsigned s3c_gpio_getcfg(unsigned int pin);
/**
* s3c_gpio_cfgpin_range() - Change the GPIO function for configuring pin range
* @start: The pin number to start at
* @nr: The number of pins to configure from @start.
* @cfg: The configuration for the pin's function
*
* Call s3c_gpio_cfgpin() for the @nr pins starting at @start.
*
* @sa s3c_gpio_cfgpin.
*/
extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr,
unsigned int cfg);
/* Define values for the pull-{up,down} available for each gpio pin.
*
* These values control the state of the weak pull-{up,down} resistors
* available on most pins on the S3C series. Not all chips support both
* up or down settings, and it may be dependent on the chip that is being
* used to whether the particular mode is available.
*/
#define S3C_GPIO_PULL_NONE ((__force samsung_gpio_pull_t)0x00)
#define S3C_GPIO_PULL_DOWN ((__force samsung_gpio_pull_t)0x01)
#define S3C_GPIO_PULL_UP ((__force samsung_gpio_pull_t)0x02)
/**
* s3c_gpio_setpull() - set the state of a gpio pin pull resistor
* @pin: The pin number to configure the pull resistor.
* @pull: The configuration for the pull resistor.
*
* This function sets the state of the pull-{up,down} resistor for the
* specified pin. It will return 0 if successful, or a negative error
* code if the pin cannot support the requested pull setting.
*
* @pull is one of S3C_GPIO_PULL_NONE, S3C_GPIO_PULL_DOWN or S3C_GPIO_PULL_UP.
*/
extern int s3c_gpio_setpull(unsigned int pin, samsung_gpio_pull_t pull);
/**
* s3c_gpio_getpull() - get the pull resistor state of a gpio pin
* @pin: The pin number to get the settings for
*
* Read the pull resistor value for the specified pin.
*/
extern samsung_gpio_pull_t s3c_gpio_getpull(unsigned int pin);
/* configure `all` aspects of an gpio */
/**
* s3c_gpio_cfgall_range() - configure range of gpio functtion and pull.
* @start: The gpio number to start at.
* @nr: The number of gpio to configure from @start.
* @cfg: The configuration to use
* @pull: The pull setting to use.
*
* Run s3c_gpio_cfgpin() and s3c_gpio_setpull() over the gpio range starting
* @gpio and running for @size.
*
* @sa s3c_gpio_cfgpin
* @sa s3c_gpio_setpull
* @sa s3c_gpio_cfgpin_range
*/
extern int s3c_gpio_cfgall_range(unsigned int start, unsigned int nr,
unsigned int cfg, samsung_gpio_pull_t pull);
static inline int s3c_gpio_cfgrange_nopull(unsigned int pin, unsigned int size,
unsigned int cfg)
{
return s3c_gpio_cfgall_range(pin, size, cfg, S3C_GPIO_PULL_NONE);
}
/* Define values for the drvstr available for each gpio pin.
*
* These values control the value of the output signal driver strength,
* configurable on most pins on the S5P series.
*/
#define S5P_GPIO_DRVSTR_LV1 ((__force s5p_gpio_drvstr_t)0x0)
#define S5P_GPIO_DRVSTR_LV2 ((__force s5p_gpio_drvstr_t)0x2)
#define S5P_GPIO_DRVSTR_LV3 ((__force s5p_gpio_drvstr_t)0x1)
#define S5P_GPIO_DRVSTR_LV4 ((__force s5p_gpio_drvstr_t)0x3)
/**
* s5c_gpio_get_drvstr() - get the driver streght value of a gpio pin
* @pin: The pin number to get the settings for
*
* Read the driver streght value for the specified pin.
*/
extern s5p_gpio_drvstr_t s5p_gpio_get_drvstr(unsigned int pin);
/**
* s3c_gpio_set_drvstr() - set the driver streght value of a gpio pin
* @pin: The pin number to configure the driver streght value
* @drvstr: The new value of the driver strength
*
* This function sets the driver strength value for the specified pin.
* It will return 0 if successful, or a negative error code if the pin
* cannot support the requested setting.
*/
extern int s5p_gpio_set_drvstr(unsigned int pin, s5p_gpio_drvstr_t drvstr);
/**
* s5p_register_gpio_interrupt() - register interrupt support for a gpio group
* @pin: The pin number from the group to be registered
*
* This function registers gpio interrupt support for the group that the
* specified pin belongs to.
*
* The total number of gpio pins is quite large ob s5p series. Registering
* irq support for all of them would be a resource waste. Because of that the
* interrupt support for standard gpio pins is registered dynamically.
*
* It will return the irq number of the interrupt that has been registered
* or -ENOMEM if no more gpio interrupts can be registered. It is allowed
* to call this function more than once for the same gpio group (the group
* will be registered only once).
*/
extern int s5p_register_gpio_interrupt(int pin);
/** s5p_register_gpioint_bank() - add gpio bank for further gpio interrupt
* registration (see s5p_register_gpio_interrupt function)
* @chain_irq: chained irq number for the gpio int handler for this bank
* @start: start gpio group number of this bank
* @nr_groups: number of gpio groups handled by this bank
*
* This functions registers initial information about gpio banks that
* can be later used by the s5p_register_gpio_interrupt() function to
* enable support for gpio interrupt for particular gpio group.
*/
#ifdef CONFIG_S5P_GPIO_INT
extern int s5p_register_gpioint_bank(int chain_irq, int start, int nr_groups);
#else
#define s5p_register_gpioint_bank(chain_irq, start, nr_groups) do { } while (0)
#endif
#endif /* __PLAT_GPIO_CFG_H */
